mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-20 00:48:52 +09:00
579 lines
18 KiB
C
579 lines
18 KiB
C
/*
|
|
* (C) Copyright 2001-2005
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#undef CONFIG_SYS_RAMBOOT
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
|
|
#define CONFIG_PM826 1 /* ...on a PM8260 module */
|
|
#define CONFIG_CPM2 1 /* Has a CPM2 */
|
|
|
|
#undef CONFIG_DB_CR826_J30x_ON /* J30x jumpers on D.B. carrier */
|
|
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
|
|
#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"bootp; " \
|
|
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
|
|
"bootm"
|
|
|
|
/* enable I2C and select the hardware/software driver */
|
|
#undef CONFIG_HARD_I2C
|
|
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
|
|
# define CONFIG_SYS_I2C_SPEED 50000
|
|
# define CONFIG_SYS_I2C_SLAVE 0xFE
|
|
/*
|
|
* Software (bit-bang) I2C driver configuration
|
|
*/
|
|
#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
|
|
#define I2C_ACTIVE (iop->pdir |= 0x00010000)
|
|
#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
|
|
#define I2C_READ ((iop->pdat & 0x00010000) != 0)
|
|
#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
|
|
else iop->pdat &= ~0x00010000
|
|
#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
|
|
else iop->pdat &= ~0x00020000
|
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
|
|
|
|
|
#define CONFIG_RTC_PCF8563
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
|
|
|
|
/*
|
|
* select serial console configuration
|
|
*
|
|
* if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
|
|
* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
|
|
* for SCC).
|
|
*
|
|
* if CONFIG_CONS_NONE is defined, then the serial console routines must
|
|
* defined elsewhere (for example, on the cogent platform, there are serial
|
|
* ports on the motherboard which are used for the serial console - see
|
|
* cogent/cma101/serial.[ch]).
|
|
*/
|
|
#define CONFIG_CONS_ON_SMC /* define if console on SMC */
|
|
#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
|
|
#undef CONFIG_CONS_NONE /* define if console on something else*/
|
|
#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
|
|
|
|
/*
|
|
* select ethernet configuration
|
|
*
|
|
* if CONFIG_ETHER_ON_SCC is selected, then
|
|
* - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
|
|
* - CONFIG_NET_MULTI must not be defined
|
|
*
|
|
* if CONFIG_ETHER_ON_FCC is selected, then
|
|
* - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
|
|
* - CONFIG_NET_MULTI must be defined
|
|
*
|
|
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
|
|
* defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
|
|
*/
|
|
#define CONFIG_NET_MULTI
|
|
#undef CONFIG_ETHER_NONE /* define if ether on something else */
|
|
|
|
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
|
|
#define CONFIG_ETHER_INDEX 1 /* which SCC channel for ethernet */
|
|
|
|
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
|
|
/*
|
|
* - Rx-CLK is CLK11
|
|
* - Tx-CLK is CLK10
|
|
*/
|
|
#define CONFIG_ETHER_ON_FCC1
|
|
# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
|
|
#ifndef CONFIG_DB_CR826_J30x_ON
|
|
# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
|
|
#else
|
|
# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
|
|
#endif
|
|
/*
|
|
* - Rx-CLK is CLK15
|
|
* - Tx-CLK is CLK14
|
|
*/
|
|
#define CONFIG_ETHER_ON_FCC2
|
|
# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
|
|
# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
|
|
/*
|
|
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
|
|
* - Enable Full Duplex in FSMR
|
|
*/
|
|
# define CONFIG_SYS_CPMFCR_RAMTYPE 0
|
|
# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
|
|
|
|
/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
|
|
#define CONFIG_8260_CLKIN 64000000 /* in Hz */
|
|
|
|
#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
|
|
#define CONFIG_BAUDRATE 230400
|
|
#else
|
|
#define CONFIG_BAUDRATE 9600
|
|
#endif
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_BEDBUG
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_DOC
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_NFS
|
|
#define CONFIG_CMD_SNTP
|
|
|
|
#ifdef CONFIG_PCI
|
|
#define CONFIG_CMD_PCI
|
|
#endif
|
|
|
|
|
|
#define CONFIG_NAND_LEGACY
|
|
|
|
/*
|
|
* Disk-On-Chip configuration
|
|
*/
|
|
|
|
#define CONFIG_SYS_DOC_SHORT_TIMEOUT
|
|
#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
|
|
|
|
#define CONFIG_SYS_DOC_SUPPORT_2000
|
|
#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
|
|
#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Flash and Boot ROM mapping
|
|
*/
|
|
#ifdef CONFIG_FLASH_32MB
|
|
#define CONFIG_SYS_FLASH0_BASE 0x40000000
|
|
#define CONFIG_SYS_FLASH0_SIZE 0x02000000
|
|
#else
|
|
#define CONFIG_SYS_FLASH0_BASE 0xFF000000
|
|
#define CONFIG_SYS_FLASH0_SIZE 0x00800000
|
|
#endif
|
|
#define CONFIG_SYS_BOOTROM_BASE 0xFF800000
|
|
#define CONFIG_SYS_BOOTROM_SIZE 0x00080000
|
|
#define CONFIG_SYS_DOC_BASE 0xFF800000
|
|
#define CONFIG_SYS_DOC_SIZE 0x00100000
|
|
|
|
/* Flash bank size (for preliminary settings)
|
|
*/
|
|
#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
|
|
#ifdef CONFIG_FLASH_32MB
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max num of sects on one chip */
|
|
#else
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
|
|
#endif
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
|
|
|
|
#if 0
|
|
/* Start port with environment in flash; switch to EEPROM later */
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x40000)
|
|
#define CONFIG_ENV_SIZE 0x40000
|
|
#define CONFIG_ENV_SECT_SIZE 0x40000
|
|
#else
|
|
/* Final version: environment in EEPROM */
|
|
#define CONFIG_ENV_IS_IN_EEPROM 1
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
|
|
#define CONFIG_ENV_OFFSET 512
|
|
#define CONFIG_ENV_SIZE (2048 - 512)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Hard Reset Configuration Words
|
|
*
|
|
* if you change bits in the HRCW, you must also change the CONFIG_SYS_*
|
|
* defines for the various registers affected by the HRCW e.g. changing
|
|
* HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
|
|
*/
|
|
#if defined(CONFIG_BOOT_ROM)
|
|
#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
|
|
#else
|
|
#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
|
|
#endif
|
|
|
|
/* no slaves so just fill with zeros */
|
|
#define CONFIG_SYS_HRCW_SLAVE1 0
|
|
#define CONFIG_SYS_HRCW_SLAVE2 0
|
|
#define CONFIG_SYS_HRCW_SLAVE3 0
|
|
#define CONFIG_SYS_HRCW_SLAVE4 0
|
|
#define CONFIG_SYS_HRCW_SLAVE5 0
|
|
#define CONFIG_SYS_HRCW_SLAVE6 0
|
|
#define CONFIG_SYS_HRCW_SLAVE7 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xF0000000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*
|
|
* 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM
|
|
* is mapped at SDRAM_BASE2_PRELIM.
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
|
|
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
|
|
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
# define CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
#ifdef CONFIG_PCI
|
|
#define CONFIG_PCI_PNP
|
|
#define CONFIG_EEPRO100
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
|
|
#endif
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* HIDx - Hardware Implementation-dependent Registers 2-11
|
|
*-----------------------------------------------------------------------
|
|
* HID0 also contains cache control - initially enable both caches and
|
|
* invalidate contents, then the final state leaves only the instruction
|
|
* cache enabled. Note that Power-On and Hard reset invalidate the caches,
|
|
* but Soft reset does not.
|
|
*
|
|
* HID1 has only read-only information - nothing to set.
|
|
*/
|
|
#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
|
|
HID0_IFEM|HID0_ABE)
|
|
#define CONFIG_SYS_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE)
|
|
#define CONFIG_SYS_HID2 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RMR - Reset Mode Register 5-5
|
|
*-----------------------------------------------------------------------
|
|
* turn on Checkstop Reset Enable
|
|
*/
|
|
#define CONFIG_SYS_RMR RMR_CSRE
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* BCR - Bus Configuration 4-25
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
#define BCR_APD01 0x10000000
|
|
#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 4-31
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#if 0
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01)
|
|
#else
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10)
|
|
#endif
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 4-35
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
|
|
SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
|
|
SYPCR_SWRI|SYPCR_SWP)
|
|
#endif /* CONFIG_WATCHDOG */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TMCNTSC - Time Counter Status and Control 4-40
|
|
*-----------------------------------------------------------------------
|
|
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
|
|
* and enable Time Counter
|
|
*/
|
|
#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 4-42
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
|
|
* Periodic timer
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock Control 9-8
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_SCCR (SCCR_DFBRG00)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RCCR - RISC Controller Configuration 13-7
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RCCR 0
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* Bank Bus Machine PortSz Device
|
|
* ---- --- ------- ------ ------
|
|
* 0 60x GPCM 64 bit FLASH
|
|
* 1 60x SDRAM 64 bit SDRAM
|
|
*
|
|
*/
|
|
|
|
/* Initialize SDRAM on local bus
|
|
*/
|
|
#define CONFIG_SYS_INIT_LOCAL_SDRAM
|
|
|
|
|
|
/* Minimum mask to separate preliminary
|
|
* address ranges for CS[0:2]
|
|
*/
|
|
#define CONFIG_SYS_MIN_AM_MASK 0xC0000000
|
|
|
|
/*
|
|
* we use the same values for 32 MB and 128 MB SDRAM
|
|
* refresh rate = 7.73 uS (64 MHz Bus Clock)
|
|
*/
|
|
#define CONFIG_SYS_MPTPR 0x2000
|
|
#define CONFIG_SYS_PSRT 0x0E
|
|
|
|
#define CONFIG_SYS_MRS_OFFS 0x00000000
|
|
|
|
|
|
#if defined(CONFIG_BOOT_ROM)
|
|
/*
|
|
* Bank 0 - Boot ROM (8 bit wide)
|
|
*/
|
|
#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
|
|
BRx_PS_8 |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_3_CLK |\
|
|
ORxG_EHTR |\
|
|
ORxG_TRLX)
|
|
|
|
/*
|
|
* Bank 1 - Flash (64 bit wide)
|
|
*/
|
|
#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_3_CLK |\
|
|
ORxG_EHTR |\
|
|
ORxG_TRLX)
|
|
|
|
#else /* ! CONFIG_BOOT_ROM */
|
|
|
|
/*
|
|
* Bank 0 - Flash (64 bit wide)
|
|
*/
|
|
#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_3_CLK |\
|
|
ORxG_EHTR |\
|
|
ORxG_TRLX)
|
|
|
|
/*
|
|
* Bank 1 - Disk-On-Chip
|
|
*/
|
|
#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_DOC_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_8 |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DOC_SIZE) |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_3_CLK |\
|
|
ORxG_EHTR |\
|
|
ORxG_TRLX)
|
|
|
|
#endif /* CONFIG_BOOT_ROM */
|
|
|
|
/* Bank 2 - SDRAM
|
|
*/
|
|
|
|
#ifndef CONFIG_SYS_RAMBOOT
|
|
#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_MS_SDRAM_P |\
|
|
BRx_V)
|
|
|
|
/* SDRAM initialization values for 8-column chips
|
|
*/
|
|
#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI0_A9 |\
|
|
ORxS_NUMR_12)
|
|
|
|
#define CONFIG_SYS_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\
|
|
PSDMR_BSMA_A14_A16 |\
|
|
PSDMR_SDA10_PBI0_A10 |\
|
|
PSDMR_RFRC_7_CLK |\
|
|
PSDMR_PRETOACT_2W |\
|
|
PSDMR_ACTTORW_1W |\
|
|
PSDMR_LDOTOPRE_1C |\
|
|
PSDMR_WRC_1C |\
|
|
PSDMR_CL_2)
|
|
|
|
/* SDRAM initialization values for 9-column chips
|
|
*/
|
|
#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI0_A7 |\
|
|
ORxS_NUMR_13)
|
|
|
|
#define CONFIG_SYS_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\
|
|
PSDMR_BSMA_A13_A15 |\
|
|
PSDMR_SDA10_PBI0_A9 |\
|
|
PSDMR_RFRC_7_CLK |\
|
|
PSDMR_PRETOACT_2W |\
|
|
PSDMR_ACTTORW_1W |\
|
|
PSDMR_LDOTOPRE_1C |\
|
|
PSDMR_WRC_1C |\
|
|
PSDMR_CL_2)
|
|
|
|
#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_9COL
|
|
#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_9COL
|
|
|
|
#endif /* CONFIG_SYS_RAMBOOT */
|
|
|
|
#endif /* __CONFIG_H */
|