mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-24 19:08:50 +09:00
![]() This patch re-formats the arm920t s3c24x0 driver files, excluding the nand driver, in preparation for changes to add support for the Embest SBC2440-II Board. The changes are as follows: - re-indent the code using Lindent - make sure register layouts are defined using a C struct - replace the upper-case typedef'ed C struct names with lower case non-typedef'ed ones - make sure registers are accessed using the proper accessor functions - run checkpatch.pl and fix any error reports It assumes the following patch has been applied first: - [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009 - patches 1/4 and 2/4 of this series Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have any s3c2400 or s3c2410 boards but need this patch applying before I can submit patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400, smdk2410 and trab configs to use the mtd nand driver (which isn't used by any board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or errors were found. Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> |
||
---|---|---|
.. | ||
auto_update.c | ||
cmd_trab.c | ||
config.mk | ||
flash.c | ||
lowlevel_init.S | ||
Makefile | ||
memory.c | ||
Pt1000_temp_data.h | ||
README.kbd | ||
rs485.c | ||
rs485.h | ||
trab_fkt.c | ||
trab.c | ||
tsc2000.c | ||
tsc2000.h | ||
u-boot.lds | ||
vfd.c |
The TRAB keyboard implementation is similar to that for LWMON and R360MPI boards. The only difference concerns key naming. There are 4 keys on TRAB: 1, 2, 3, 4. 1) The "kbd" command provides information about the current state of the keys. For example, TRAB # kbd Keys: 1 0 1 0 means that keys 1 and 3 are pressed. The keyboard status is also stored in the "keybd" environment variable. In this example we get keybd=1010 2) The "preboot" variable is set according to current environment settings and keys pressed. This is an example: TRAB # setenv magic_keys XY TRAB # setenv key_magicX 12 TRAB # setenv key_cmdX echo ## Keys 1 + 2 pressed ##\;echo TRAB # setenv key_magicY 13 TRAB # setenv key_cmdY echo ## Keys 1 + 3 pressed ##\;echo Here "magic_keys=XY" means that the "key_magicX" and "key_magicY" variables will be checked for a match. Each variable "key_magic*" defines a set of keys. In the our example, if keys 1 and 3 are pressed during reset, then "key_magicY" matches, so the "preboot" variable will be set to the contents of "key_cmdY": preboot=echo ## Keys 1 + 3 pressed ##;echo 3) The TRAB board has optional modem support. When a certain key combination is pressed on the keyboard at power-on, the firmware performs the necessary initialization of the modem and allows for dial-in. The key combination is specified in the "include/configs/trab.h" file. For example: #define CONFIG_MODEM_KEY_MAGIC "23" means that modem will be initialized if and only if both keys 2, 3 are pressed. Note that the format of this string is similar to the format of "key_magic*" environment variables described above.