mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-23 10:28:51 +09:00
![Tom Rini](/assets/img/avatar_default.png)
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
133 lines
4.0 KiB
C
133 lines
4.0 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2014 Topic Embedded Products
|
|
*
|
|
* Configuration for Zynq Evaluation and Development Board - Miami
|
|
* See zynq-common.h for Zynq common configs
|
|
*/
|
|
|
|
#ifndef __CONFIG_TOPIC_MIAMI_H
|
|
#define __CONFIG_TOPIC_MIAMI_H
|
|
|
|
|
|
/* Speed up boot time by ignoring the environment which we never used */
|
|
|
|
#include "zynq-common.h"
|
|
|
|
/* Fixup settings */
|
|
#undef CONFIG_ENV_SIZE
|
|
#define CONFIG_ENV_SIZE 0x8000
|
|
#undef CONFIG_ENV_OFFSET
|
|
#define CONFIG_ENV_OFFSET 0x80000
|
|
|
|
/* SPL settings */
|
|
#undef CONFIG_SPL_ETH_SUPPORT
|
|
#undef CONFIG_SYS_SPI_U_BOOT_OFFS
|
|
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
|
|
#undef CONFIG_SPL_MAX_FOOTPRINT
|
|
#define CONFIG_SPL_MAX_FOOTPRINT CONFIG_SYS_SPI_U_BOOT_OFFS
|
|
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
|
|
|
|
/* sspi command isn't useful */
|
|
#undef CONFIG_CMD_SPI
|
|
|
|
/* No useful gpio */
|
|
#undef CONFIG_ZYNQ_GPIO
|
|
#undef CONFIG_CMD_GPIO
|
|
|
|
/* No falcon support */
|
|
#undef CONFIG_SPL_OS_BOOT
|
|
#undef CONFIG_SPL_FPGA_SUPPORT
|
|
|
|
/* FPGA commands that we don't use */
|
|
|
|
/* Extras */
|
|
#undef CONFIG_SYS_MEMTEST_START
|
|
#define CONFIG_SYS_MEMTEST_START 0
|
|
#undef CONFIG_SYS_MEMTEST_END
|
|
#define CONFIG_SYS_MEMTEST_END 0x18000000
|
|
|
|
/* Faster flash, ours may run at 108 MHz */
|
|
#undef CONFIG_SF_DEFAULT_SPEED
|
|
#define CONFIG_SF_DEFAULT_SPEED 108000000
|
|
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
|
|
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
|
|
#undef CONFIG_SPI_FLASH_WINBOND
|
|
#undef CONFIG_SPI_FLASH_ISSI
|
|
|
|
/* Setup proper boot sequences for Miami boards */
|
|
|
|
#if defined(CONFIG_USB)
|
|
# define EXTRA_ENV_USB \
|
|
"usbreset=i2c dev 1 && i2c mw 41 1 ff && i2c mw 41 3 fe && "\
|
|
"i2c mw 41 1 fe && i2c mw 41 1 ff\0" \
|
|
"usbboot=run usbreset && if usb start; then " \
|
|
"echo Booting from USB... && " \
|
|
"if load usb 0 0x1900000 ${bootscript}; then "\
|
|
"source 0x1900000; fi; " \
|
|
"load usb 0 ${kernel_addr} ${kernel_image} && " \
|
|
"load usb 0 ${devicetree_addr} ${devicetree_image} && " \
|
|
"load usb 0 ${ramdisk_load_address} ${ramdisk_image} && " \
|
|
"bootm ${kernel_addr} ${ramdisk_load_address} "\
|
|
"${devicetree_addr}; " \
|
|
"fi\0"
|
|
/* Note that addresses here should match the addresses in the env */
|
|
# undef DFU_ALT_INFO
|
|
# define DFU_ALT_INFO \
|
|
"dfu_alt_info=" \
|
|
"uImage ram 0x2080000 0x500000;" \
|
|
"devicetree.dtb ram 0x2000000 0x20000;" \
|
|
"uramdisk.image.gz ram 0x4000000 0x10000000\0" \
|
|
"dfu_ram=run usbreset && dfu 0 ram 0\0" \
|
|
"thor_ram=run usbreset && thordown 0 ram 0\0"
|
|
#else
|
|
# define EXTRA_ENV_USB
|
|
#endif
|
|
|
|
#undef CONFIG_PREBOOT
|
|
|
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"kernel_image=uImage\0" \
|
|
"kernel_addr=0x2080000\0" \
|
|
"ramdisk_image=uramdisk.image.gz\0" \
|
|
"ramdisk_load_address=0x4000000\0" \
|
|
"devicetree_image=devicetree.dtb\0" \
|
|
"devicetree_addr=0x2000000\0" \
|
|
"bitstream_image=fpga.bin\0" \
|
|
"bootscript=autorun.scr\0" \
|
|
"loadbit_addr=0x100000\0" \
|
|
"loadbootenv_addr=0x2000000\0" \
|
|
"kernel_size=0x440000\0" \
|
|
"devicetree_size=0x10000\0" \
|
|
"boot_size=0xF00000\0" \
|
|
"fdt_high=0x20000000\0" \
|
|
"initrd_high=0x20000000\0" \
|
|
"mmc_loadbit=echo Loading bitstream from SD/MMC/eMMC to RAM.. && " \
|
|
"mmcinfo && " \
|
|
"load mmc 0 ${loadbit_addr} ${bitstream_image} && " \
|
|
"fpga load 0 ${loadbit_addr} ${filesize}\0" \
|
|
"qspiboot=echo Booting from QSPI flash... && " \
|
|
"sf probe && " \
|
|
"sf read ${devicetree_addr} 0xA0000 ${devicetree_size} && " \
|
|
"sf read ${kernel_addr} 0xC0000 ${kernel_size} && " \
|
|
"bootm ${kernel_addr} - ${devicetree_addr}\0" \
|
|
"sdboot=if mmcinfo; then " \
|
|
"setenv bootargs console=ttyPS0,115200 " \
|
|
"root=/dev/mmcblk0p2 rw rootfstype=ext4 " \
|
|
"rootwait quiet ; " \
|
|
"load mmc 0 ${kernel_addr} ${kernel_image}&& " \
|
|
"load mmc 0 ${devicetree_addr} ${devicetree_image}&& " \
|
|
"bootm ${kernel_addr} - ${devicetree_addr}; " \
|
|
"fi\0" \
|
|
EXTRA_ENV_USB \
|
|
DFU_ALT_INFO
|
|
|
|
#undef CONFIG_BOOTCOMMAND
|
|
#define CONFIG_BOOTCOMMAND "if mmcinfo; then " \
|
|
"if fatload mmc 0 0x1900000 ${bootscript}; then source 0x1900000; " \
|
|
"fi; fi; run $modeboot"
|
|
#undef CONFIG_DISPLAY_BOARDINFO
|
|
|
|
#endif /* __CONFIG_TOPIC_MIAMI_H */
|