mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-21 17:38:51 +09:00
![]() When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com> |
||
---|---|---|
.. | ||
cpld.c | ||
cpld.h | ||
ddr.c | ||
eth.c | ||
Kconfig | ||
MAINTAINERS | ||
Makefile | ||
p2041rdb.c | ||
README |
Overview ========= The P2041 Processor combines four Power Architecture processor cores with high-performance datapath acceleration architecture(DPAA), CoreNet fabric infrastructure, as well as network and peripheral bus interfaces required for networking, telecom/datacom, wireless infrastructure, and military/aerospace applications. P2041RDB board is a quad core platform supporting the P2041 processor of QorIQ DPAA series. Boot from NOR flash =================== 1. Build image make P2041RDB_config make all 2. Program image => tftp 1000000 u-boot.bin => protect off all => erase eff40000 efffffff => cp.b 1000000 eff40000 c0000 3. Program RCW => tftp 1000000 rcw.bin => protect off all => erase e8000000 e801ffff => cp.b 1000000 e8000000 50 4. Program FMAN Firmware ucode => tftp 1000000 ucode.bin => protect off all => erase eff00000 eff3ffff => cp.b 1000000 eff00000 2000 5. Change DIP-switch SW1[1-5] = 10110 Note: 1 stands for 'on', 0 stands for 'off' Boot from SDCard =================== 1. Build image make P2041RDB_SDCARD_config make all 2. Generate PBL imge Use PE tool to produce a image used to be programed to SDCard which contains RCW and U-Boot image. 3. Program the PBL image to SDCard => tftp 1000000 pbl_sd.bin => mmcinfo => mmc write 1000000 8 672 4. Program FMAN Firmware ucode => tftp 1000000 ucode.bin => mmc write 1000000 690 10 5. Change DIP-switch SW1[1-5] = 01100 Note: 1 stands for 'on', 0 stands for 'off' Boot from SPI flash =================== 1. Build image make P2041RDB_SPIFLASH_config make all 2. Generate PBL imge Use PE tool to produce a image used to be programed to SPI flash which contains RCW and U-Boot image. 3. Program the PBL image to SPI flash => tftp 1000000 pbl_spi.bin => spi probe 0 => sf erase 0 100000 => sf write 1000000 0 $filesize 4. Program FMAN Firmware ucode => tftp 1000000 ucode.bin => sf erase 110000 10000 => sf write 1000000 110000 $filesize 5. Change DIP-switch SW1[1-5] = 10100 Note: 1 stands for 'on', 0 stands for 'off' CPLD command ============ The CPLD is used to control the power sequence and some serdes lane mux function. cpld reset - hard reset to default bank cpld reset altbank - reset to alternate bank cpld lane_mux <lane> <mux_value> - set multiplexed lane pin lane 6: 0 -> slot1 (Default) 1 -> SGMII lane a: 0 -> slot2 (Default) 1 -> AURORA lane c: 0 -> slot2 (Default) 1 -> SATA0 lane d: 0 -> slot2 (Default) 1 -> SATA1 Using the Device Tree Source File ================================= To create the DTB (Device Tree Binary) image file, use a command similar to this: dtc -O dtb -b 0 -p 1024 p2041rdb.dts > p2041rdb.dtb Or use the following command: {linux-2.6}/make p2041rdb.dtb ARCH=powerpc then the dtb file will be generated under the following directory: {linux-2.6}/arch/powerpc/boot/p2041rdb.dtb Booting Linux ============= Place a linux uImage in the TFTP disk area. tftp 1000000 uImage tftp 2000000 rootfs.ext2.gz.uboot tftp 3000000 p2041rdb.dtb bootm 1000000 2000000 3000000