mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-26 20:09:02 +09:00
![Tom Rini](/assets/img/avatar_default.png)
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
277 lines
6.5 KiB
C
277 lines
6.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2007-2008
|
|
* Stelian Pop <stelian@popies.net>
|
|
* Lead Tech Design <www.leadtechdesign.com>
|
|
*
|
|
* (C) Copyright 2009-2015
|
|
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
|
|
* esd electronic system design gmbh <www.esd.eu>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/arch/at91sam9_smc.h>
|
|
#include <asm/arch/at91_common.h>
|
|
#include <asm/arch/at91_pmc.h>
|
|
#include <asm/arch/at91_rstc.h>
|
|
#include <asm/arch/at91_matrix.h>
|
|
#include <asm/arch/at91_pio.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <netdev.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/*
|
|
* Miscelaneous platform dependent initialisations
|
|
*/
|
|
|
|
#ifdef CONFIG_REVISION_TAG
|
|
static int hw_rev = -1; /* hardware revision */
|
|
|
|
int get_hw_rev(void)
|
|
{
|
|
if (hw_rev >= 0)
|
|
return hw_rev;
|
|
|
|
hw_rev = at91_get_pio_value(AT91_PIO_PORTB, 19);
|
|
hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 20) << 1;
|
|
hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 21) << 2;
|
|
hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 22) << 3;
|
|
|
|
if (hw_rev == 15)
|
|
hw_rev = 0;
|
|
|
|
return hw_rev;
|
|
}
|
|
#endif /* CONFIG_REVISION_TAG */
|
|
|
|
#ifdef CONFIG_CMD_NAND
|
|
static void meesc_nand_hw_init(void)
|
|
{
|
|
unsigned long csa;
|
|
at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0;
|
|
at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
|
|
|
|
/* Enable CS3 */
|
|
csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
|
|
writel(csa, &matrix->csa[0]);
|
|
|
|
/* Configure SMC CS3 for NAND/SmartMedia */
|
|
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
|
|
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(2),
|
|
&smc->cs[3].setup);
|
|
|
|
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
|
|
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
|
|
&smc->cs[3].pulse);
|
|
|
|
writel(AT91_SMC_CYCLE_NWE(6) | AT91_SMC_CYCLE_NRD(6),
|
|
&smc->cs[3].cycle);
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
AT91_SMC_MODE_DBW_8 |
|
|
AT91_SMC_MODE_TDF_CYCLE(12),
|
|
&smc->cs[3].mode);
|
|
|
|
/* Configure RDY/BSY */
|
|
gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
|
|
|
|
/* Enable NandFlash */
|
|
gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
|
|
}
|
|
#endif /* CONFIG_CMD_NAND */
|
|
|
|
#ifdef CONFIG_MACB
|
|
static void meesc_macb_hw_init(void)
|
|
{
|
|
at91_periph_clk_enable(ATMEL_ID_EMAC);
|
|
|
|
at91_macb_hw_init();
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* Static memory controller initialization to enable Beckhoff ET1100 EtherCAT
|
|
* controller debugging
|
|
* The ET1100 is located at physical address 0x70000000
|
|
* Its process memory is located at physical address 0x70001000
|
|
*/
|
|
static void meesc_ethercat_hw_init(void)
|
|
{
|
|
at91_smc_t *smc1 = (at91_smc_t *) ATMEL_BASE_SMC1;
|
|
|
|
/* Configure SMC EBI1_CS0 for EtherCAT */
|
|
writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(0) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc1->cs[0].setup);
|
|
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(9) |
|
|
AT91_SMC_PULSE_NRD(5) | AT91_SMC_PULSE_NCS_RD(9),
|
|
&smc1->cs[0].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(10) | AT91_SMC_CYCLE_NRD(6),
|
|
&smc1->cs[0].cycle);
|
|
/*
|
|
* Configure behavior at external wait signal, byte-select mode, 16 bit
|
|
* data bus width, none data float wait states and TDF optimization
|
|
*/
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_EXNW_READY |
|
|
AT91_SMC_MODE_DBW_16 | AT91_SMC_MODE_TDF_CYCLE(0) |
|
|
AT91_SMC_MODE_TDF, &smc1->cs[0].mode);
|
|
|
|
/* Configure RDY/BSY */
|
|
at91_set_b_periph(AT91_PIO_PORTE, 20, 0); /* EBI1_NWAIT */
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
/* dram_init must store complete ramsize in gd->ram_size */
|
|
gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
|
|
PHYS_SDRAM_SIZE);
|
|
return 0;
|
|
}
|
|
|
|
int dram_init_banksize(void)
|
|
{
|
|
gd->bd->bi_dram[0].start = PHYS_SDRAM;
|
|
gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int rc = 0;
|
|
#ifdef CONFIG_MACB
|
|
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
|
|
#endif
|
|
return rc;
|
|
}
|
|
|
|
#ifdef CONFIG_DISPLAY_BOARDINFO
|
|
int checkboard(void)
|
|
{
|
|
char str[32];
|
|
u_char hw_type; /* hardware type */
|
|
|
|
/* read the "Type" register of the ET1100 controller */
|
|
hw_type = readb(CONFIG_ET1100_BASE);
|
|
|
|
switch (hw_type) {
|
|
case 0x11:
|
|
case 0x3F:
|
|
/* ET1100 present, arch number of MEESC-Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_MEESC;
|
|
puts("Board: CAN-EtherCAT Gateway");
|
|
break;
|
|
case 0xFF:
|
|
/* no ET1100 present, arch number of EtherCAN/2-Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
|
|
puts("Board: EtherCAN/2 Gateway");
|
|
/* switch on LED1D */
|
|
at91_set_pio_output(AT91_PIO_PORTB, 12, 1);
|
|
break;
|
|
default:
|
|
/* assume, no ET1100 present, arch number of EtherCAN/2-Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
|
|
printf("ERROR! Read invalid hw_type: %02X\n", hw_type);
|
|
puts("Board: EtherCAN/2 Gateway");
|
|
break;
|
|
}
|
|
if (env_get_f("serial#", str, sizeof(str)) > 0) {
|
|
puts(", serial# ");
|
|
puts(str);
|
|
}
|
|
#ifdef CONFIG_REVISION_TAG
|
|
printf("\nHardware-revision: 1.%d\n", get_hw_rev());
|
|
#endif
|
|
printf("Mach-type: %lu\n", gd->bd->bi_arch_number);
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_DISPLAY_BOARDINFO */
|
|
|
|
#ifdef CONFIG_SERIAL_TAG
|
|
void get_board_serial(struct tag_serialnr *serialnr)
|
|
{
|
|
char *str;
|
|
|
|
char *serial = env_get("serial#");
|
|
if (serial) {
|
|
str = strchr(serial, '_');
|
|
if (str && (strlen(str) >= 4)) {
|
|
serialnr->high = (*(str + 1) << 8) | *(str + 2);
|
|
serialnr->low = simple_strtoul(str + 3, NULL, 16);
|
|
}
|
|
} else {
|
|
serialnr->high = 0;
|
|
serialnr->low = 0;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_REVISION_TAG
|
|
u32 get_board_rev(void)
|
|
{
|
|
return hw_rev | 0x100;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_MISC_INIT_R
|
|
int misc_init_r(void)
|
|
{
|
|
char *str;
|
|
char buf[32];
|
|
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
|
|
|
|
/*
|
|
* Normally the processor clock has a divisor of 2.
|
|
* In some cases this this needs to be set to 4.
|
|
* Check the user has set environment mdiv to 4 to change the divisor.
|
|
*/
|
|
str = env_get("mdiv");
|
|
if (str && (strcmp(str, "4") == 0)) {
|
|
writel((readl(&pmc->mckr) & ~AT91_PMC_MDIV) |
|
|
AT91SAM9_PMC_MDIV_4, &pmc->mckr);
|
|
at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK);
|
|
serial_setbrg();
|
|
/* Notify the user that the clock is not default */
|
|
printf("Setting master clock to %s MHz\n",
|
|
strmhz(buf, get_mck_clk_rate()));
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_MISC_INIT_R */
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
at91_periph_clk_enable(ATMEL_ID_UHP);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* initialize ET1100 Controller */
|
|
meesc_ethercat_hw_init();
|
|
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
#ifdef CONFIG_CMD_NAND
|
|
meesc_nand_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_MACB
|
|
meesc_macb_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_AT91_CAN
|
|
at91_can_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_USB_OHCI_NEW
|
|
at91_uhp_hw_init();
|
|
#endif
|
|
return 0;
|
|
}
|