mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-31 06:18:51 +09:00
![]() Before we can sync with the latest mach-types.h file from the Linux Kernel we need to remove some instances of MACH_TYPE_xxx from our sources. As these values have been removed from the canonical upstream source we should not be using them either, so drop. Cc: Tom Warren <twarren@nvidia.com> Cc: Lucas Stach <dev@lynxeye.de> Cc: Luka Perkov <luka@openwrt.org> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Heiko Schocher <hs@denx.de> Cc: Thomas Weber <weber@corscience.de> Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com> Cc: Matthias Weisser <weisserm@arcor.de> Cc: Suriyan Ramasami <suriyan.r@gmail.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Bo Shen <voice.shen@atmel.com> Cc: Nick Thompson <nick.thompson@gefanuc.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Erik van Luijk <evanluijk@interact.nl> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
||
---|---|---|
.. | ||
da850evm.c | ||
Kconfig | ||
MAINTAINERS | ||
Makefile | ||
omapl138_lcdk.c | ||
README.da850 | ||
u-boot-spl-da850evm.lds |
Summary ======= The README is for the boot procedure used for various DA850 (or compatible parts such as the AM1808) based boards. In the context of U-Boot, the board is booted in three stages. The initial bootloader which executes upon reset is the ROM Boot Loader (RBL) and sits in the internal ROM. The RBL initializes the internal memory and then depending on the exact board and pin configurations will initialize another controller (such as SPI or NAND) to continue the boot process by loading the secondary program loader (SPL). The SPL will initialize the system further (some clocks, SDRAM) and then load the full u-boot from a predefined location in persistent storage to DDR and jumps to the u-boot entry point. AIS is an image format defined by TI for the images that are to be loaded to memory by the RBL. The image is divided into a series of sections and the image's entry point is specified. Each section comes with meta data like the target address the section is to be copied to and the size of the section, which is used by the RBL to load the image. At the end of the image the RBL jumps to the image entry point. The AIS format allows for other things such as programming the clocks and SDRAM if the header is programmed for it. We do not take advantage of this and instead use SPL as it allows for additional flexibility (run-time detect of board revision, loading the next image from a different media, etc). Compilation =========== The exact build target you need will depend on the board you have. For Logic PD boards, or other boards which store the ethernet MAC address at the end of SPI flash, run 'make da850evm'. For boards which store the ethernet MAC address in the i2c EEPROM located at 0x50, run 'make da850_am18xxevm'. Once this build completes you will have a u-boot.ais file that needs to be written to the correct persistent storage. Flashing the images to SPI ========================== The AIS image can be written to SPI flash using the following commands. Assuming that the network is configured and enabled and the u-boot.ais file is tftp'able. U-Boot > sf probe 0 U-Boot > sf erase 0 +320000 U-Boot > tftp u-boot.ais U-Boot > sf write c0700000 0 $filesize Recovery ======== In the case of a "bricked" board, you need to use the TI tools found here[1] to write the u-boot.ais file. An example of recovering to the SPI flash of an AM1808 would be: $ mono sfh_OMAP-L138.exe -targetType AM1808 -p /dev/ttyUSB0 \ -flash_noubl /path/to/u-boot.ais For other target types and flash locations: $ mono sfh_OMAP-L138.exe -h Links ===== [1] http://processors.wiki.ti.com/index.php/Serial_Boot_and_Flash_Loading_Utility_for_OMAP-L138