brain-hackers_pepepper-mirror/u-boot-brain
1
0
Fork 0
mirror of https://github.com/brain-hackers/u-boot-brain synced 2024-07-06 03:06:16 +09:00
Code Issues Projects Releases Wiki Activity
529a671279
u-boot-brain/board/freescale/mx6slevk/mx6slevk.c
Fabio Estevam 529a671279 mx6slevk: Fix the reset delay for the the LAN8720 PHY 
Since commit 59370f3fcd ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional.

This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.

According to the LAN8720 datasheet tpurstd (time that reset line should
stay asserted) is 25ms.

So do as suggested in order to have Ethernet working again.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02 21:18:44 +01:00

524 lines
13 KiB
C
Raw Blame History

/*
* Copyright (C) 2013 Freescale Semiconductor, Inc.
*
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <asm/arch/clock.h>
#include <asm/arch/iomux.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/spi.h>
#include <asm/io.h>
#include <linux/sizes.h>
#include <common.h>
#include <fsl_esdhc.h>
#include <i2c.h>
#include <mmc.h>
#include <netdev.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
#include "../common/pfuze.h"
#include <usb.h>
#include <usb/ehci-fsl.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PUS_22K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
#define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\
PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
PAD_CTL_SRE_FAST)
#define ETH_PHY_RESET IMX_GPIO_NR(4, 21)
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
return 0;
}
static iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const usdhc1_pads[] = {
/* 8 bit SD */
MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT0__USDHC1_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT1__USDHC1_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT2__USDHC1_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT3__USDHC1_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT4__USDHC1_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT5__USDHC1_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT6__USDHC1_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT7__USDHC1_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
/*CD pin*/
MX6_PAD_KEY_ROW7__GPIO_4_7 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const usdhc2_pads[] = {
MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
/*CD pin*/
MX6_PAD_SD2_DAT7__GPIO_5_0 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const usdhc3_pads[] = {
MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
/*CD pin*/
MX6_PAD_REF_CLK_32K__GPIO_3_22 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const fec_pads[] = {
MX6_PAD_FEC_MDC__FEC_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_MDIO__FEC_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_CRS_DV__FEC_RX_DV | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_RXD0__FEC_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_RXD1__FEC_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_TX_EN__FEC_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_TXD0__FEC_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_TXD1__FEC_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_REF_CLK__FEC_REF_OUT | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_FEC_RX_ER__GPIO_4_19 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_FEC_TX_CLK__GPIO_4_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
#ifdef CONFIG_MXC_SPI
static iomux_v3_cfg_t ecspi1_pads[] = {
MX6_PAD_ECSPI1_MISO__ECSPI_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_ECSPI1_SS0__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
int board_spi_cs_gpio(unsigned bus, unsigned cs)
{
return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 11)) : -1;
}
static void setup_spi(void)
{
imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
}
#endif
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
static void setup_iomux_fec(void)
{
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
/* Reset LAN8720 PHY */
gpio_direction_output(ETH_PHY_RESET , 0);
udelay(25000);
gpio_set_value(ETH_PHY_RESET, 1);
}
#define USDHC1_CD_GPIO IMX_GPIO_NR(4, 7)
#define USDHC2_CD_GPIO IMX_GPIO_NR(5, 0)
#define USDHC3_CD_GPIO IMX_GPIO_NR(3, 22)
static struct fsl_esdhc_cfg usdhc_cfg[3] = {
{USDHC1_BASE_ADDR},
{USDHC2_BASE_ADDR, 0, 4},
{USDHC3_BASE_ADDR, 0, 4},
};
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
switch (cfg->esdhc_base) {
case USDHC1_BASE_ADDR:
ret = !gpio_get_value(USDHC1_CD_GPIO);
break;
case USDHC2_BASE_ADDR:
ret = !gpio_get_value(USDHC2_CD_GPIO);
break;
case USDHC3_BASE_ADDR:
ret = !gpio_get_value(USDHC3_CD_GPIO);
break;
}
return ret;
}
int board_mmc_init(bd_t *bis)
{
#ifndef CONFIG_SPL_BUILD
int i, ret;
/*
* According to the board_mmc_init() the following map is done:
* (U-boot device node) (Physical Port)
* mmc0 USDHC1
* mmc1 USDHC2
* mmc2 USDHC3
*/
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
case 0:
imx_iomux_v3_setup_multiple_pads(
usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
gpio_direction_input(USDHC1_CD_GPIO);
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
break;
case 1:
imx_iomux_v3_setup_multiple_pads(
usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
gpio_direction_input(USDHC2_CD_GPIO);
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
break;
case 2:
imx_iomux_v3_setup_multiple_pads(
usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
gpio_direction_input(USDHC3_CD_GPIO);
usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
break;
default:
printf("Warning: you configured more USDHC controllers"
"(%d) than supported by the board\n", i + 1);
return -EINVAL;
}
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
if (ret) {
printf("Warning: failed to initialize "
"mmc dev %d\n", i);
return ret;
}
}
return 0;
#else
struct src *src_regs = (struct src *)SRC_BASE_ADDR;
u32 val;
u32 port;
val = readl(&src_regs->sbmr1);
/* Boot from USDHC */
port = (val >> 11) & 0x3;
switch (port) {
case 0:
imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
ARRAY_SIZE(usdhc1_pads));
gpio_direction_input(USDHC1_CD_GPIO);
usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
break;
case 1:
imx_iomux_v3_setup_multiple_pads(usdhc2_pads,
ARRAY_SIZE(usdhc2_pads));
gpio_direction_input(USDHC2_CD_GPIO);
usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
usdhc_cfg[0].max_bus_width = 4;
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
break;
case 2:
imx_iomux_v3_setup_multiple_pads(usdhc3_pads,
ARRAY_SIZE(usdhc3_pads));
gpio_direction_input(USDHC3_CD_GPIO);
usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
usdhc_cfg[0].max_bus_width = 4;
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
break;
}
gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
#endif
}
#ifdef CONFIG_SYS_I2C_MXC
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
/* I2C1 for PMIC */
struct i2c_pads_info i2c_pad_info1 = {
.sda = {
.i2c_mode = MX6_PAD_I2C1_SDA__I2C1_SDA | PC,
.gpio_mode = MX6_PAD_I2C1_SDA__GPIO_3_13 | PC,
.gp = IMX_GPIO_NR(3, 13),
},
.scl = {
.i2c_mode = MX6_PAD_I2C1_SCL__I2C1_SCL | PC,
.gpio_mode = MX6_PAD_I2C1_SCL__GPIO_3_12 | PC,
.gp = IMX_GPIO_NR(3, 12),
},
};
int power_init_board(void)
{
struct pmic *p;
p = pfuze_common_init(I2C_PMIC);
if (!p)
return -ENODEV;
return pfuze_mode_init(p, APS_PFM);
}
#endif
#ifdef CONFIG_FEC_MXC
int board_eth_init(bd_t *bis)
{
setup_iomux_fec();
return cpu_eth_init(bis);
}
static int setup_fec(void)
{
struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
/* clear gpr1[14], gpr1[18:17] to select anatop clock */
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0);
return enable_fec_anatop_clock(0, ENET_50MHZ);
}
#endif
#ifdef CONFIG_USB_EHCI_MX6
#define USB_OTHERREGS_OFFSET 0x800
#define UCTRL_PWR_POL (1 << 9)
static iomux_v3_cfg_t const usb_otg_pads[] = {
/* OTG1 */
MX6_PAD_KEY_COL4__USB_USBOTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_EPDC_PWRCOM__ANATOP_USBOTG1_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
/* OTG2 */
MX6_PAD_KEY_COL5__USB_USBOTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
};
static void setup_usb(void)
{
imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
ARRAY_SIZE(usb_otg_pads));
}
int board_usb_phy_mode(int port)
{
if (port == 1)
return USB_INIT_HOST;
else
return usb_phy_mode(port);
}
int board_ehci_hcd_init(int port)
{
u32 *usbnc_usb_ctrl;
if (port > 1)
return -EINVAL;
usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
port * 4);
/* Set Power polarity */
setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
return 0;
}
#endif
int board_early_init_f(void)
{
setup_iomux_uart();
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_SYS_I2C_MXC
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
#endif
#ifdef CONFIG_FEC_MXC
setup_fec();
#endif
#ifdef CONFIG_USB_EHCI_MX6
setup_usb();
#endif
return 0;
}
int checkboard(void)
{
puts("Board: MX6SLEVK\n");
return 0;
}
#ifdef CONFIG_SPL_BUILD
#include <spl.h>
#include <libfdt.h>
const struct mx6sl_iomux_ddr_regs mx6_ddr_ioregs = {
.dram_sdqs0 = 0x00003030,
.dram_sdqs1 = 0x00003030,
.dram_sdqs2 = 0x00003030,
.dram_sdqs3 = 0x00003030,
.dram_dqm0 = 0x00000030,
.dram_dqm1 = 0x00000030,
.dram_dqm2 = 0x00000030,
.dram_dqm3 = 0x00000030,
.dram_cas = 0x00000030,
.dram_ras = 0x00000030,
.dram_sdclk_0 = 0x00000028,
.dram_reset = 0x00000030,
.dram_sdba2 = 0x00000000,
.dram_odt0 = 0x00000008,
.dram_odt1 = 0x00000008,
};
const struct mx6sl_iomux_grp_regs mx6_grp_ioregs = {
.grp_b0ds = 0x00000030,
.grp_b1ds = 0x00000030,
.grp_b2ds = 0x00000030,
.grp_b3ds = 0x00000030,
.grp_addds = 0x00000030,
.grp_ctlds = 0x00000030,
.grp_ddrmode_ctl = 0x00020000,
.grp_ddrpke = 0x00000000,
.grp_ddrmode = 0x00020000,
.grp_ddr_type = 0x00080000,
};
const struct mx6_mmdc_calibration mx6_mmcd_calib = {
.p0_mpdgctrl0 = 0x20000000,
.p0_mpdgctrl1 = 0x00000000,
.p0_mprddlctl = 0x4241444a,
.p0_mpwrdlctl = 0x3030312b,
.mpzqlp2ctl = 0x1b4700c7,
};
static struct mx6_lpddr2_cfg mem_ddr = {
.mem_speed = 800,
.density = 4,
.width = 32,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.trcd_lp = 2000,
.trppb_lp = 2000,
.trpab_lp = 2250,
.trasmin = 4200,
};
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
writel(0xFFFFFFFF, &ccm->CCGR0);
writel(0xFFFFFFFF, &ccm->CCGR1);
writel(0xFFFFFFFF, &ccm->CCGR2);
writel(0xFFFFFFFF, &ccm->CCGR3);
writel(0xFFFFFFFF, &ccm->CCGR4);
writel(0xFFFFFFFF, &ccm->CCGR5);
writel(0xFFFFFFFF, &ccm->CCGR6);
writel(0x00260324, &ccm->cbcmr);
}
static void spl_dram_init(void)
{
struct mx6_ddr_sysinfo sysinfo = {
.dsize = mem_ddr.width / 32,
.cs_density = 20,
.ncs = 2,
.cs1_mirror = 0,
.walat = 0,
.ralat = 2,
.mif3_mode = 3,
.bi_on = 1,
.rtt_wr = 0, /* LPDDR2 does not need rtt_wr rtt_nom */
.rtt_nom = 0,
.sde_to_rst = 0, /* LPDDR2 does not need this field */
.rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */
.ddr_type = DDR_TYPE_LPDDR2,
};
mx6sl_dram_iocfg(32, &mx6_ddr_ioregs, &mx6_grp_ioregs);
mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
}
void board_init_f(ulong dummy)
{
/* setup AIPS and disable watchdog */
arch_cpu_init();
ccgr_init();
/* iomux and setup of i2c */
board_early_init_f();
/* setup GP timer */
timer_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
/* DDR initialization */
spl_dram_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
/* load/boot image from boot device */
board_init_r(NULL, 0);
}
#endif
Reference in New Issue View Git Blame Copy Permalink