mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-22 18:09:03 +09:00
390 lines
13 KiB
C
390 lines
13 KiB
C
/*
|
|
* Parameters for GTH board
|
|
* Based on FADS860T
|
|
* by thomas.lange@corelatus.com
|
|
|
|
* A collection of structures, addresses, and values associated with
|
|
* the Motorola 860T FADS board. Copied from the MBX stuff.
|
|
* Magnus Damm added defines for 8xxrom and extended bd_info.
|
|
* Helmut Buchsbaum added bitvalues for BCSRx
|
|
*
|
|
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
|
|
*/
|
|
|
|
/*
|
|
* ff000000 -> ff00ffff : IMAP internal in the cpu
|
|
* e0000000 -> ennnnnnn : pcmcia
|
|
* 98000000 -> 983nnnnn : FPGA 4MB
|
|
* 90000000 -> 903nnnnn : FPGA 4MB
|
|
* 80000000 -> 80nnnnnn : flash connected to CS0, final ( real ) location
|
|
* 00000000 -> nnnnnnnn : sdram
|
|
*/
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
#include <mpc8xx_irq.h>
|
|
|
|
#define CONFIG_MPC860 1
|
|
#define CONFIG_MPC860T 1
|
|
#define CONFIG_GTH 1
|
|
|
|
#define CONFIG_MISC_INIT_R 1
|
|
|
|
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
|
|
#undef CONFIG_8xx_CONS_SMC2
|
|
#undef CONFIG_8xx_CONS_NONE
|
|
#define CONFIG_BAUDRATE 9600
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
|
|
#define MPC8XX_FACT 3 /* Multiply by 3 */
|
|
#define MPC8XX_XIN 16384000 /* 16.384 MHz */
|
|
#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
|
|
|
|
#define CONFIG_BOOTDELAY 1 /* autoboot after 0 seconds */
|
|
|
|
#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */
|
|
|
|
#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */
|
|
|
|
#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */
|
|
|
|
/* Only interrupt boot if space is pressed */
|
|
/* If a long serial cable is connected but */
|
|
/* other end is dead, garbage will be read */
|
|
#define CONFIG_AUTOBOOT_KEYED 1
|
|
#define CONFIG_AUTOBOOT_PROMPT \
|
|
"Press space to abort autoboot in %d second\n", bootdelay
|
|
#define CONFIG_AUTOBOOT_DELAY_STR "d"
|
|
#define CONFIG_AUTOBOOT_STOP_STR " "
|
|
|
|
#if 0
|
|
/* Net boot */
|
|
/* Loads a tftp image and starts it */
|
|
#define CONFIG_BOOTCOMMAND "bootp;bootm 100000" /* autoboot command */
|
|
#define CONFIG_BOOTARGS "panic=1"
|
|
#else
|
|
/* Compact flash boot */
|
|
#define CONFIG_BOOTARGS "panic=1 root=/dev/hda7"
|
|
#define CONFIG_BOOTCOMMAND "disk 100000 0:5;bootm 100000"
|
|
#endif
|
|
|
|
/* Enable watchdog */
|
|
#define CONFIG_WATCHDOG 1
|
|
|
|
/* choose SCC1 ethernet (10BASET on motherboard)
|
|
* or FEC ethernet (10/100 on daughterboard)
|
|
*/
|
|
#if 1
|
|
#define CONFIG_SCC1_ENET 1 /* use SCC1 ethernet */
|
|
#undef CONFIG_FEC_ENET /* disable FEC ethernet */
|
|
#define CONFIG_SYS_DISCOVER_PHY
|
|
#else
|
|
#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
|
|
#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
|
|
#define CONFIG_SYS_DISCOVER_PHY
|
|
#endif
|
|
#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
|
|
#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
|
|
#endif
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_IDE
|
|
|
|
|
|
#define CONFIG_MAC_PARTITION
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_PROMPT "=>" /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
|
|
|
|
/* Default location to load data from net */
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000
|
|
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400 }
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xFF000000
|
|
#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
|
|
#define CONFIG_SYS_FLASH_BASE 0x80000000
|
|
|
|
#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
|
|
|
|
#define CONFIG_SYS_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#undef CONFIG_ENV_IS_IN_EEPROM
|
|
#define CONFIG_ENV_OFFSET 0x000E0000
|
|
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
|
|
|
|
#define CONFIG_ENV_SECT_SIZE 0x50000 /* see README - env sector total size */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
*-----------------------------------------------------------------------
|
|
* PCMCIA config., multi-function pin tri-state
|
|
*/
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
*-----------------------------------------------------------------------
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
|
|
|
|
/*----------------------------------------------------------------------
|
|
* RTCSC - Real-Time Clock Status and Control Register 11-27
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
/*FIXME dont use for now */
|
|
/*#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
|
|
/*#define CONFIG_SYS_RTCSC (RTCSC_RTF) */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
/* PITE */
|
|
/*-----------------------------------------------------------------------
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
*-----------------------------------------------------------------------
|
|
* set the PLL, the low-power modes and the reset control (15-29)
|
|
*/
|
|
#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
|
|
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
*-----------------------------------------------------------------------
|
|
* Set clock output, timebase and RTC source and divider,
|
|
* power management and some other internal clocks
|
|
*/
|
|
|
|
/* FIXME check values */
|
|
#define SCCR_MASK SCCR_EBDF11
|
|
#define CONFIG_SYS_SCCR (SCCR_TBS|SCCR_RTSEL|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
*
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_DER 0
|
|
|
|
/* Because of the way the 860 starts up and assigns CS0 the
|
|
* entire address space, we have to set the memory controller
|
|
* differently. Normally, you write the option register
|
|
* first, and then enable the chip select by writing the
|
|
* base register. For CS0, you must write the base register
|
|
* first, followed by the option register.
|
|
*/
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0/1 and OR0/1 (FLASH)
|
|
*/
|
|
/* the other CS:s are determined by looking at parameters in BCSRx */
|
|
|
|
#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
|
|
|
|
#define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* 4 MB OR addr mask */
|
|
#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
|
|
|
|
#define FPGA_2_BASE 0x90000000
|
|
#define FPGA_3_BASE 0x98000000
|
|
|
|
/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
|
|
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
|
|
|
|
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16 )
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
#define CONFIG_ETHADDR DE:AD:BE:EF:00:01 /* Ethernet address */
|
|
|
|
#ifdef CONFIG_MPC860T
|
|
|
|
/* Interrupt level assignments.
|
|
*/
|
|
#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
|
|
|
|
#endif /* CONFIG_MPC860T */
|
|
|
|
/* We don't use the 8259.
|
|
*/
|
|
#define NR_8259_INTS 0
|
|
|
|
/* Machine type
|
|
*/
|
|
#define _MACH_8xx (_MACH_gth)
|
|
|
|
#ifdef CONFIG_MPC860
|
|
#define PCMCIA_SLOT_A 1
|
|
#define CONFIG_PCMCIA_SLOT_A 1
|
|
#endif
|
|
|
|
#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
|
|
#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
|
|
#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
|
|
#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
|
|
|
|
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
|
|
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
|
|
#undef CONFIG_IDE_LED /* LED for ide not supported */
|
|
#undef CONFIG_IDE_RESET /* reset for ide not supported */
|
|
|
|
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
|
|
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
|
|
/* Offset for data I/O */
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
/* Offset for normal register accesses */
|
|
#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
/* Offset for alternate registers */
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
|
|
|
|
#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */
|
|
|
|
#define PA_FRONT_LED ((u16)0x4) /* PA 13 */
|
|
#define PA_FL_CONFIG ((u16)0x20) /* PA 10 */
|
|
#define PA_FL_CE ((u16)0x1000) /* PA 3 */
|
|
|
|
#define PB_ID_GND ((u32)1) /* PB 31 */
|
|
#define PB_REV_1 ((u32)2) /* PB 30 */
|
|
#define PB_REV_0 ((u32)4) /* PB 29 */
|
|
#define PB_BLUE_LED ((u32)0x400) /* PB 21 */
|
|
#define PB_EEPROM ((u32)0x800) /* PB 20 */
|
|
#define PB_ID_3 ((u32)0x2000) /* PB 18 */
|
|
#define PB_ID_2 ((u32)0x4000) /* PB 17 */
|
|
#define PB_ID_1 ((u32)0x8000) /* PB 16 */
|
|
#define PB_ID_0 ((u32)0x10000) /* PB 15 */
|
|
|
|
/* NOTE. This is reset for 100Mbit port only */
|
|
#define PC_ENET100_RESET ((ushort)0x0080) /* PC 8 */
|
|
|
|
#endif /* __CONFIG_H */
|