mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-18 16:08:53 +09:00
![Wolfgang Denk](/assets/img/avatar_default.png)
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
653 lines
20 KiB
C
653 lines
20 KiB
C
/*****************************************************************************
|
|
* (C) Copyright 2003; Tundra Semiconductor Corp.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*****************************************************************************/
|
|
|
|
/*----------------------------------------------------------------------------
|
|
* FILENAME: tsi108_init.c
|
|
*
|
|
* Originator: Alex Bounine
|
|
*
|
|
* DESCRIPTION:
|
|
* Initialization code for the Tundra Tsi108 bridge chip
|
|
*---------------------------------------------------------------------------*/
|
|
|
|
#include <common.h>
|
|
#include <74xx_7xx.h>
|
|
#include <config.h>
|
|
#include <version.h>
|
|
#include <asm/processor.h>
|
|
#include <tsi108.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
extern void mpicInit (int verbose);
|
|
|
|
/*
|
|
* Configuration Options
|
|
*/
|
|
|
|
typedef struct {
|
|
ulong upper;
|
|
ulong lower;
|
|
} PB2OCN_LUT_ENTRY;
|
|
|
|
PB2OCN_LUT_ENTRY pb2ocn_lut1[32] = {
|
|
/* 0 - 7 */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE000_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE100_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE200_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE300_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE400_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE500_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE600_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE700_0000 -> PCI/X (Byte-Swap) */
|
|
|
|
/* 8 - 15 */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE800_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xE900_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xEA00_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xEB00_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xEC00_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xED00_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xEE00_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xEF00_0000 -> PCI/X (Byte-Swap) */
|
|
|
|
/* 16 - 23 */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF000_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF100_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF200_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF300_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF400_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF500_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF600_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF700_0000 -> PCI/X (Byte-Swap) */
|
|
/* 24 - 31 */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF800_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xF900_0000 -> PCI/X (Byte-Swap) */
|
|
{0x00000000, 0x00000241}, /* PBA=0xFA00_0000 -> PCI/X PCI I/O (Byte-Swap + Translate) */
|
|
{0x00000000, 0x00000201}, /* PBA=0xFB00_0000 -> PCI/X PCI Config (Byte-Swap) */
|
|
|
|
{0x00000000, 0x02000240}, /* PBA=0xFC00_0000 -> HLP */
|
|
{0x00000000, 0x01000240}, /* PBA=0xFD00_0000 -> HLP */
|
|
{0x00000000, 0x03000240}, /* PBA=0xFE00_0000 -> HLP */
|
|
{0x00000000, 0x00000240} /* PBA=0xFF00_0000 -> HLP : (Translation Enabled + Byte-Swap)*/
|
|
};
|
|
|
|
#ifdef CONFIG_SYS_CLK_SPREAD
|
|
typedef struct {
|
|
ulong ctrl0;
|
|
ulong ctrl1;
|
|
} PLL_CTRL_SET;
|
|
|
|
/*
|
|
* Clock Generator SPLL0 initialization values
|
|
* PLL0 configuration table for various PB_CLKO freq.
|
|
* Uses pre-calculated values for Fs = 30 kHz, D = 0.5%
|
|
* Fout depends on required PB_CLKO. Based on Fref = 33 MHz
|
|
*/
|
|
|
|
static PLL_CTRL_SET pll0_config[8] = {
|
|
{0x00000000, 0x00000000}, /* 0: bypass */
|
|
{0x00000000, 0x00000000}, /* 1: reserved */
|
|
{0x00430044, 0x00000043}, /* 2: CG_PB_CLKO = 183 MHz */
|
|
{0x005c0044, 0x00000039}, /* 3: CG_PB_CLKO = 100 MHz */
|
|
{0x005c0044, 0x00000039}, /* 4: CG_PB_CLKO = 133 MHz */
|
|
{0x004a0044, 0x00000040}, /* 5: CG_PB_CLKO = 167 MHz */
|
|
{0x005c0044, 0x00000039}, /* 6: CG_PB_CLKO = 200 MHz */
|
|
{0x004f0044, 0x0000003e} /* 7: CG_PB_CLKO = 233 MHz */
|
|
};
|
|
#endif /* CONFIG_SYS_CLK_SPREAD */
|
|
|
|
/*
|
|
* Prosessor Bus Clock (in MHz) defined by CG_PB_SELECT
|
|
* (based on recommended Tsi108 reference clock 33MHz)
|
|
*/
|
|
static int pb_clk_sel[8] = { 0, 0, 183, 100, 133, 167, 200, 233 };
|
|
|
|
/*
|
|
* get_board_bus_clk ()
|
|
*
|
|
* returns the bus clock in Hz.
|
|
*/
|
|
unsigned long get_board_bus_clk (void)
|
|
{
|
|
ulong i;
|
|
|
|
/* Detect PB clock freq. */
|
|
i = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
|
|
i = (i >> 16) & 0x07; /* Get PB PLL multiplier */
|
|
|
|
return pb_clk_sel[i] * 1000000;
|
|
}
|
|
|
|
/*
|
|
* board_early_init_f ()
|
|
*
|
|
* board-specific initialization executed from flash
|
|
*/
|
|
|
|
int board_early_init_f (void)
|
|
{
|
|
ulong i;
|
|
|
|
gd->mem_clk = 0;
|
|
i = in32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET +
|
|
CG_PWRUP_STATUS);
|
|
i = (i >> 20) & 0x07; /* Get GD PLL multiplier */
|
|
switch (i) {
|
|
case 0: /* external clock */
|
|
printf ("Using external clock\n");
|
|
break;
|
|
case 1: /* system clock */
|
|
gd->mem_clk = gd->bus_clk;
|
|
break;
|
|
case 4: /* 133 MHz */
|
|
case 5: /* 166 MHz */
|
|
case 6: /* 200 MHz */
|
|
gd->mem_clk = pb_clk_sel[i] * 1000000;
|
|
break;
|
|
default:
|
|
printf ("Invalid DDR2 clock setting\n");
|
|
return -1;
|
|
}
|
|
printf ("BUS: %lu MHz\n", get_board_bus_clk() / 1000000);
|
|
printf ("MEM: %lu MHz\n", gd->mem_clk / 1000000);
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* board_early_init_r() - Tsi108 initialization function executed right after
|
|
* relocation. Contains code that cannot be executed from flash.
|
|
*/
|
|
|
|
int board_early_init_r (void)
|
|
{
|
|
ulong temp, i;
|
|
ulong reg_val;
|
|
volatile ulong *reg_ptr;
|
|
|
|
reg_ptr =
|
|
(ulong *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900);
|
|
|
|
for (i = 0; i < 32; i++) {
|
|
*reg_ptr++ = 0x00000201; /* SWAP ENABLED */
|
|
*reg_ptr++ = 0x00;
|
|
}
|
|
|
|
__asm__ __volatile__ ("eieio");
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Setup PB_OCN_BAR2: size 256B + ENable @ 0x0_80000000 */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2,
|
|
0x80000001);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Make sure that OCN_BAR2 decoder is set (to allow following immediate
|
|
* read from SDRAM)
|
|
*/
|
|
|
|
temp = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/*
|
|
* Remap PB_OCN_BAR1 to accomodate PCI-bus aperture and EPROM into the
|
|
* processor bus address space. Immediately after reset LUT and address
|
|
* translation are disabled for this BAR. Now we have to initialize LUT
|
|
* and switch from the BOOT mode to the normal operation mode.
|
|
*
|
|
* The aperture defined by PB_OCN_BAR1 startes at address 0xE0000000
|
|
* and covers 512MB of address space. To allow larger aperture we also
|
|
* have to relocate register window of Tsi108
|
|
*
|
|
* Initialize LUT (32-entries) prior switching PB_OCN_BAR1 from BOOT
|
|
* mode.
|
|
*
|
|
* initialize pointer to LUT associated with PB_OCN_BAR1
|
|
*/
|
|
reg_ptr =
|
|
(ulong *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x800);
|
|
|
|
for (i = 0; i < 32; i++) {
|
|
*reg_ptr++ = pb2ocn_lut1[i].lower;
|
|
*reg_ptr++ = pb2ocn_lut1[i].upper;
|
|
}
|
|
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Base addresses for CS0, CS1, CS2, CS3 */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_ADDR,
|
|
0x00000000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_ADDR,
|
|
0x00100000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_ADDR,
|
|
0x00200000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_ADDR,
|
|
0x00300000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Masks for HLP banks */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_MASK,
|
|
0xFFF00000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_MASK,
|
|
0xFFF00000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_MASK,
|
|
0xFFF00000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_MASK,
|
|
0xFFF00000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Set CTRL0 values for banks */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL0,
|
|
0x7FFC44C2);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL0,
|
|
0x7FFC44C0);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL0,
|
|
0x7FFC44C0);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL0,
|
|
0x7FFC44C2);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Set banks to latched mode, enabled, and other default settings */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL1,
|
|
0x7C0F2000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL1,
|
|
0x7C0F2000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL1,
|
|
0x7C0F2000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1,
|
|
0x7C0F2000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/*
|
|
* Set new value for PB_OCN_BAR1: switch from BOOT to LUT mode.
|
|
* value for PB_OCN_BAR1: (BA-0xE000_0000 + size 512MB + ENable)
|
|
*/
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1,
|
|
0xE0000011);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Make sure that OCN_BAR2 decoder is set (to allow following
|
|
* immediate read from SDRAM)
|
|
*/
|
|
|
|
temp = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/*
|
|
* SRI: At this point we have enabled the HLP banks. That means we can
|
|
* now read from the NVRAM and initialize the environment variables.
|
|
* We will over-ride the env_init called in board_init_f
|
|
* This is really a work-around because, the HLP bank 1
|
|
* where NVRAM resides is not visible during board_init_f
|
|
* (arch/powerpc/lib/board.c)
|
|
* Alternatively, we could use the I2C EEPROM at start-up to configure
|
|
* and enable all HLP banks and not just HLP 0 as is being done for
|
|
* Taiga Rev. 2.
|
|
*/
|
|
|
|
env_init ();
|
|
|
|
#ifndef DISABLE_PBM
|
|
|
|
/*
|
|
* For IBM processors we have to set Address-Only commands generated
|
|
* by PBM that are different from ones set after reset.
|
|
*/
|
|
|
|
temp = get_cpu_type ();
|
|
|
|
if ((CPU_750FX == temp) || (CPU_750GX == temp))
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_MCMD,
|
|
0x00009955);
|
|
#endif /* DISABLE_PBM */
|
|
|
|
#ifdef CONFIG_PCI
|
|
/*
|
|
* Initialize PCI/X block
|
|
*/
|
|
|
|
/* Map PCI/X Configuration Space (16MB @ 0x0_FE000000) */
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
|
|
PCI_PFAB_BAR0_UPPER, 0);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_BAR0,
|
|
0xFB000001);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Set Bus Number for the attached PCI/X bus (we will use 0 for NB) */
|
|
|
|
temp = in32(CONFIG_SYS_TSI108_CSR_BASE +
|
|
TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT);
|
|
|
|
temp &= ~0xFF00; /* Clear the BUS_NUM field */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT,
|
|
temp);
|
|
|
|
/* Map PCI/X IO Space (64KB @ 0x0_FD000000) takes one 16MB LUT entry */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO_UPPER,
|
|
0);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* This register is on the PCI side to interpret the address it receives
|
|
* and maps it as a IO address.
|
|
*/
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO,
|
|
0x00000001);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/*
|
|
* Map PCI/X Memory Space
|
|
*
|
|
* Transactions directed from OCM to PCI Memory Space are directed
|
|
* from PB to PCI
|
|
* unchanged (as defined by PB_OCN_BAR1,2 and LUT settings).
|
|
* If address remapping is required the corresponding PCI_PFAB_MEM32
|
|
* and PCI_PFAB_PFMx register groups have to be configured.
|
|
*
|
|
* Map the path from the PCI/X bus into the system memory
|
|
*
|
|
* The memory mapped window assotiated with PCI P2O_BAR2 provides
|
|
* access to the system memory without address remapping.
|
|
* All system memory is opened for accesses initiated by PCI/X bus
|
|
* masters.
|
|
*
|
|
* Initialize LUT associated with PCI P2O_BAR2
|
|
*
|
|
* set pointer to LUT associated with PCI P2O_BAR2
|
|
*/
|
|
|
|
reg_ptr =
|
|
(ulong *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x500);
|
|
|
|
#ifdef DISABLE_PBM
|
|
|
|
/* In case when PBM is disabled (no HW supported cache snoopng on PB)
|
|
* P2O_BAR2 is directly mapped into the system memory without address
|
|
* translation.
|
|
*/
|
|
|
|
reg_val = 0x00000004; /* SDRAM port + NO Addr_Translation */
|
|
|
|
for (i = 0; i < 32; i++) {
|
|
*reg_ptr++ = reg_val; /* P2O_BAR2_LUTx */
|
|
*reg_ptr++ = 0; /* P2O_BAR2_LUT_UPPERx */
|
|
}
|
|
|
|
/* value for PCI BAR2 (size = 512MB, Enabled, No Addr. Translation) */
|
|
reg_val = 0x00007500;
|
|
#else
|
|
|
|
reg_val = 0x00000002; /* Destination port = PBM */
|
|
|
|
for (i = 0; i < 32; i++) {
|
|
*reg_ptr++ = reg_val; /* P2O_BAR2_LUTx */
|
|
/* P2O_BAR2_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */
|
|
*reg_ptr++ = 0x40000000;
|
|
/* offset = 16MB, address translation is enabled to allow byte swapping */
|
|
reg_val += 0x01000000;
|
|
}
|
|
|
|
/* value for PCI BAR2 (size = 512MB, Enabled, Address Translation Enabled) */
|
|
reg_val = 0x00007100;
|
|
#endif
|
|
|
|
__asm__ __volatile__ ("eieio");
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
|
|
reg_val);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Set 64-bit PCI bus address for system memory
|
|
* ( 0 is the best choice for easy mapping)
|
|
*/
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2,
|
|
0x00000000);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2_UPPER,
|
|
0x00000000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
#ifndef DISABLE_PBM
|
|
/*
|
|
* The memory mapped window assotiated with PCI P2O_BAR3 provides
|
|
* access to the system memory using SDRAM OCN port and address
|
|
* translation. This is alternative way to access SDRAM from PCI
|
|
* required for Tsi108 emulation testing.
|
|
* All system memory is opened for accesses initiated by
|
|
* PCI/X bus masters.
|
|
*
|
|
* Initialize LUT associated with PCI P2O_BAR3
|
|
*
|
|
* set pointer to LUT associated with PCI P2O_BAR3
|
|
*/
|
|
reg_ptr =
|
|
(ulong *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x600);
|
|
|
|
reg_val = 0x00000004; /* Destination port = SDC */
|
|
|
|
for (i = 0; i < 32; i++) {
|
|
*reg_ptr++ = reg_val; /* P2O_BAR3_LUTx */
|
|
|
|
/* P2O_BAR3_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */
|
|
*reg_ptr++ = 0;
|
|
|
|
/* offset = 16MB, address translation is enabled to allow byte swapping */
|
|
reg_val += 0x01000000;
|
|
}
|
|
|
|
__asm__ __volatile__ ("eieio");
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Configure PCI P2O_BAR3 (size = 512MB, Enabled) */
|
|
|
|
reg_val =
|
|
in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
|
|
PCI_P2O_PAGE_SIZES);
|
|
reg_val &= ~0x00FF;
|
|
reg_val |= 0x0071;
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
|
|
reg_val);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/* Set 64-bit base PCI bus address for window (0x20000000) */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3_UPPER,
|
|
0x00000000);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3,
|
|
0x20000000);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
#endif /* !DISABLE_PBM */
|
|
|
|
#ifdef ENABLE_PCI_CSR_BAR
|
|
/* open if required access to Tsi108 CSRs from the PCI/X bus */
|
|
/* enable BAR0 on the PCI/X bus */
|
|
reg_val = in32(CONFIG_SYS_TSI108_CSR_BASE +
|
|
TSI108_PCI_REG_OFFSET + PCI_MISC_CSR);
|
|
reg_val |= 0x02;
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR,
|
|
reg_val);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0_UPPER,
|
|
0x00000000);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0,
|
|
CONFIG_SYS_TSI108_CSR_BASE);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
#endif
|
|
|
|
/*
|
|
* Finally enable PCI/X Bus Master and Memory Space access
|
|
*/
|
|
|
|
reg_val = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR);
|
|
reg_val |= 0x06;
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
#endif /* CONFIG_PCI */
|
|
|
|
/*
|
|
* Initialize MPIC outputs (interrupt pins):
|
|
* Interrupt routing on the Grendel Emul. Board:
|
|
* PB_INT[0] -> INT (CPU0)
|
|
* PB_INT[1] -> INT (CPU1)
|
|
* PB_INT[2] -> MCP (CPU0)
|
|
* PB_INT[3] -> MCP (CPU1)
|
|
* Set interrupt controller outputs as Level_Sensitive/Active_Low
|
|
*/
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(0), 0x02);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(1), 0x02);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(2), 0x02);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(3), 0x02);
|
|
__asm__ __volatile__ ("sync");
|
|
|
|
/*
|
|
* Ensure that Machine Check exception is enabled
|
|
* We need it to support PCI Bus probing (configuration reads)
|
|
*/
|
|
|
|
reg_val = mfmsr ();
|
|
mtmsr(reg_val | MSR_ME);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Needed to print out L2 cache info
|
|
* used in the misc_init_r function
|
|
*/
|
|
|
|
unsigned long get_l2cr (void)
|
|
{
|
|
unsigned long l2controlreg;
|
|
asm volatile ("mfspr %0, 1017":"=r" (l2controlreg):);
|
|
return l2controlreg;
|
|
}
|
|
|
|
/*
|
|
* misc_init_r()
|
|
*
|
|
* various things to do after relocation
|
|
*
|
|
*/
|
|
|
|
int misc_init_r (void)
|
|
{
|
|
#ifdef CONFIG_SYS_CLK_SPREAD /* Initialize Spread-Spectrum Clock generation */
|
|
ulong i;
|
|
|
|
/* Ensure that Spread-Spectrum is disabled */
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, 0);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0);
|
|
|
|
/* Initialize PLL1: CG_PCI_CLK , internal OCN_CLK
|
|
* Uses pre-calculated value for Fout = 800 MHz, Fs = 30 kHz, D = 0.5%
|
|
*/
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
|
|
0x002e0044); /* D = 0.25% */
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL1,
|
|
0x00000039); /* BWADJ */
|
|
|
|
/* Initialize PLL0: CG_PB_CLKO */
|
|
/* Detect PB clock freq. */
|
|
i = in32(CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
|
|
i = (i >> 16) & 0x07; /* Get PB PLL multiplier */
|
|
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE +
|
|
TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, pll0_config[i].ctrl0);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE +
|
|
TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL1, pll0_config[i].ctrl1);
|
|
|
|
/* Wait and set SSEN for both PLL0 and 1 */
|
|
udelay (1000);
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
|
|
0x802e0044); /* D=0.25% */
|
|
out32 (CONFIG_SYS_TSI108_CSR_BASE +
|
|
TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0,
|
|
0x80000000 | pll0_config[i].ctrl0);
|
|
#endif /* CONFIG_SYS_CLK_SPREAD */
|
|
|
|
#ifdef CONFIG_SYS_L2
|
|
l2cache_enable ();
|
|
#endif
|
|
printf ("BUS: %lu MHz\n", gd->bus_clk / 1000000);
|
|
printf ("MEM: %lu MHz\n", gd->mem_clk / 1000000);
|
|
|
|
/*
|
|
* All the information needed to print the cache details is avaiblable
|
|
* at this point i.e. above call to l2cache_enable is the very last
|
|
* thing done with regards to enabling diabling the cache.
|
|
* So this seems like a good place to print all this information
|
|
*/
|
|
|
|
printf ("CACHE: ");
|
|
switch (get_cpu_type()) {
|
|
case CPU_7447A:
|
|
printf ("L1 Instruction cache - 32KB 8-way");
|
|
(get_hid0 () & (1 << 15)) ? printf (" ENABLED\n") :
|
|
printf (" DISABLED\n");
|
|
printf ("L1 Data cache - 32KB 8-way");
|
|
(get_hid0 () & (1 << 14)) ? printf (" ENABLED\n") :
|
|
printf (" DISABLED\n");
|
|
printf ("Unified L2 cache - 512KB 8-way");
|
|
(get_l2cr () & (1 << 31)) ? printf (" ENABLED\n") :
|
|
printf (" DISABLED\n");
|
|
printf ("\n");
|
|
break;
|
|
|
|
case CPU_7448:
|
|
printf ("L1 Instruction cache - 32KB 8-way");
|
|
(get_hid0 () & (1 << 15)) ? printf (" ENABLED\n") :
|
|
printf (" DISABLED\n");
|
|
printf ("L1 Data cache - 32KB 8-way");
|
|
(get_hid0 () & (1 << 14)) ? printf (" ENABLED\n") :
|
|
printf (" DISABLED\n");
|
|
printf ("Unified L2 cache - 1MB 8-way");
|
|
(get_l2cr () & (1 << 31)) ? printf (" ENABLED\n") :
|
|
printf (" DISABLED\n");
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
return 0;
|
|
}
|