mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-23 10:28:51 +09:00
367 lines
14 KiB
Plaintext
367 lines
14 KiB
Plaintext
|
|
U-Boot for Nios-32
|
|
|
|
Last Update: February 1, 2004
|
|
====================================================================
|
|
|
|
This file contains information regarding U-Boot and the Altera
|
|
Nios CPU. For information regarding U-Boot and the Nios Development
|
|
Kits see:
|
|
|
|
* Cyclone Edition (DK-1C20), see doc/README.dk1c20
|
|
* Stratix Edition (DK-1S10), see doc/README.dk1s10 (TODO)
|
|
* Stratix Edition (DK-1S40), see doc/README.dk1s40 (TODO)
|
|
* Stratix Edition (DK-20K200), see doc/README.dk20k200 (TODO)
|
|
|
|
For informations regarding Nios Development Kit hardware overview
|
|
and the NIOS CPU standard configuration of all known boards made by
|
|
Altera see:
|
|
|
|
* Development Kit (DK) hardware overview, see doc/README.nios_DK
|
|
* NIOS CPU standard_32 at DK-1C20, see doc/README.dk1c20_std32
|
|
* NIOS CPU standard_32 at DK-1S10, see doc/README.dk1s10_std32
|
|
* NIOS CPU standard_32 at DK-1S40, see doc/README.dk1s40_std32
|
|
* NIOS CPU standard_32 at DK-20K200, see doc/README.dk20k200_std32
|
|
|
|
For those interested in contributing ... see HELP WANTED below.
|
|
|
|
|
|
1. OVERVIEW
|
|
------------
|
|
|
|
U-Boot has been successfully tested on the Nios Cyclone development
|
|
board using both the 'safe' and 'standard 32' configurations with
|
|
Nios CPU revision 3.1 (CPU_ID = 0x3018). U-Boot can be used with
|
|
or without the GERMS monitor. The initial version of U-Boot for the
|
|
Cyclone development kit is about 60 Kbyte and will fit in a single
|
|
sector of on-board FLASH. Only the Nios 32-bit CPU is supported.
|
|
|
|
1.1 GERMS Monitor
|
|
------------------
|
|
If GERMS is just not enough, then U-Boot is a great antibiotic.
|
|
You will be very pleased with its high degree of configurability
|
|
and its rich feature set.
|
|
|
|
A few of the most obvious limitations of GERMS are overcome by
|
|
using U-Boot (See 'Brain Damage'). Most notably, you can use
|
|
minicom or Hyperterminal (duh).
|
|
|
|
1.2 Altera Source Code
|
|
-----------------------
|
|
The Nios port does NOT include ANY sources that Altera has the
|
|
copyright. This was a conscious decision ... not an accident.
|
|
The Altera license is not clear in terms of distributing Altera
|
|
sources (when altera silicon is not involved). This isn't really
|
|
a problem as little, if any, of the Altera source contains
|
|
features that are not already available in U-Boot.
|
|
|
|
1.3 Debugging via OCI
|
|
---------------------
|
|
The Nios port supports debugging with gdb and/or nios-console
|
|
via the JTAG port. Stubs for debugging with gdb via the serial
|
|
port are not currently implemented.
|
|
|
|
|
|
2. CONFIGURATION OPTIONS/SETTINGS
|
|
----------------------------------
|
|
|
|
2.1 Nios-specific Options/Settings
|
|
-----------------------------------
|
|
All configuration options/settings that are specific to Nios begin
|
|
with "CONFIG_NIOS_", "CONFIG_SYS_NIOS_", or "CONFIG_SYS_NIOS_CPU_".
|
|
|
|
The configuration follows a two-stage process. In the first stage
|
|
the NIOS CPU core will defined like defined in Alteras SOPC Builder.
|
|
At this point we use the "CONFIG_SYS_NIOS_CPU_" defines exclusively. For
|
|
more informations about all the definitions you have to setup see
|
|
into current board configurations and doc/README.nios_CFG_NIOS_CPU.
|
|
|
|
In second stage we bring the NIOS CPU configuration in relation to
|
|
U-Boot configuration options/settings. The following is a list of
|
|
currently defined Nios-specific options/parameters used inside of
|
|
U-Boot. If any options are related to Standard-32 Nios SDK
|
|
excalibur.h definitions, the related definition follows the
|
|
description).
|
|
|
|
CONFIG_NIOS -- defined for all Nios-32 boards.
|
|
|
|
CONFIG_SYS_NIOS_CONSOLE -- the base address of the console UART or the JTAG
|
|
stdio port. To enable a console via JTAG, define
|
|
CONFIG_CONSOLE_JTAG and set CGF_NIOS_CONSOLE to the base address
|
|
of the JTAG stdio port (normally OCI base + 0x00fa). Then
|
|
run nios-console with the -w option.
|
|
(standard-32: nasys_uart_0 resp. na_uart1_base).
|
|
|
|
CONFIG_SYS_NIOS_FIXEDBAUD -- defined if the console UART PTF fixed_baud
|
|
parameter is set to '1'.
|
|
|
|
CONFIG_SYS_NIOS_MULT_HW -- use full hardware multiply (not yet implemented).
|
|
|
|
CONFIG_SYS_NIOS_MULT_MSTEP -- use hardware assisted multiply using the
|
|
MSTEP instruction (not yet implemented).
|
|
|
|
CONFIG_SYS_NIOS_TMRBASE -- the base address of the timer used to support
|
|
xxx_timer routines (e.g. set_timer(), get_timer(), etc.).
|
|
(standard-32: nasys_timer_1 resp. na_lo_priority_timer2_base).
|
|
|
|
CONFIG_SYS_NIOS_TMRIRQ -- the interrupt request (vector number) assigned to
|
|
the timer. (standard-32: nasys_timer_1_irq resp.
|
|
na_low_priority_timer2_irq).
|
|
|
|
CONFIG_SYS_NIOS_TMRMS -- the period of the timer in milliseconds.
|
|
|
|
CONFIG_SYS_NIOS_TMRCNT -- the preloadable counter value for the timer if it has
|
|
no fixed period.
|
|
|
|
CONFIG_SYS_NIOS_ASMIBASE -- the base address of the ASMI peripheral.
|
|
(standard-32: na_asmi_base).
|
|
|
|
CONFIG_SYS_NIOS_SPIBASE -- the base address of the SPI master (!) peripheral.
|
|
(nasys_spi_0)
|
|
|
|
CONFIG_SYS_NIOS_SPIBITS -- the amount of configured SPI data bits in PTF.
|
|
This value can be 8 or 16 only! (PTF: databits)
|
|
|
|
|
|
2.2 Differences in U-Boot Options/Settings
|
|
-------------------------------------------
|
|
Some 'standard' U-Boot options/settings are treated differently in
|
|
the Nios port. These are described below.
|
|
|
|
CONFIG_SYS_GBL_DATA_OFFSET -- in the Nios port, this is the offset of the
|
|
global data structure in the Nios memory space. More simply,
|
|
the address of global data.
|
|
|
|
|
|
3. ASSEMBLY CODING
|
|
-------------------
|
|
|
|
In browsing the assembly source files, you may notice the absence
|
|
of the 'magic macros' (e.g. MOVIA, MOVIP, ADDIP etc.). This is
|
|
deliberate. The documentation for the magic macros is scant and
|
|
it is hard to find ... it does not appear in the Nios programmer's
|
|
manual, nor does it appear in the assembler manual. Regardless,
|
|
the macros actually do very little to improve readability anyway.
|
|
|
|
With this in mind, all assembler modules use only instructions that
|
|
appear in the Nios programmer's manual OR are directly supported
|
|
by the nios-elf toolchain. For example, the 'dec %rB' instruction
|
|
is an alias for 'subi %rB,1' that is supported by the assembler
|
|
but does not appear in the programmer's manual.
|
|
|
|
|
|
4. BOOT PROCESS
|
|
---------------
|
|
|
|
4.1 Boot process over GERMS
|
|
---------------------------
|
|
When the NIOS CPU catch a reset signal it will begin to be running
|
|
code from CONFIG_SYS_NIOS_CPU_RST_VECT. Normally at this place it will
|
|
find the GERMS monitor. That's the case for the generic NIOS CPU
|
|
configuration "standard_32". When the GERMS monitor starts running,
|
|
it performs important system initializations and then looks for
|
|
executable code in flash, using the following steps:
|
|
|
|
1. Examining the two bytes at CONFIG_SYS_NIOS_CPU_FLASH_BASE + 0x04000C.
|
|
2. Examining the button 0 on the PIO CONFIG_SYS_NIOS_CPU_BUTTON_PIO.
|
|
3. If the button is not pressed and the two bytes contain 'N'
|
|
and 'i', the monitor executes a CALL to location
|
|
CONFIG_SYS_NIOS_CPU_FLASH_BASE + 0x040000.
|
|
4. If the code is not executed in step 3 or the code returns,
|
|
then prints an 8-digit version number to STDOUT and waits for
|
|
user commands from STDIN.
|
|
|
|
In normal case, for "standard_32", STDIN and STDOUT are the first
|
|
serial port.
|
|
|
|
4.2 Return to GERMS command line
|
|
--------------------------------
|
|
During the boot process, the GERMS monitor checks for the existence
|
|
of application software in flash memory. If found, the processor
|
|
immediately executes the code. To return program execution to the
|
|
GERMS monitor (that is, avoid running code stored in flash memory):
|
|
|
|
1. Hold down CONFIG_SYS_NIOS_CPU_BUTTON_PIO, button number 0.
|
|
2. Press then release the CPU reset button.
|
|
3. Release CONFIG_SYS_NIOS_CPU_BUTTON_PIO, button number 0.
|
|
|
|
|
|
5. DEBUGGING WITH GDB
|
|
---------------------
|
|
|
|
Debug sessions using gdb are currently supported only via JTAG. The
|
|
stubs for debugging via a serial port are not implemented. To enable
|
|
the gdb JTAG stubs, simply reference _brkpt_hw_int and _brkpt_sw_int
|
|
at vector table offsets 3 and 4, respectively. For an example, see
|
|
board/altera/dk1c20/vectors.S.
|
|
|
|
5.1 Vector Table Initialization and ROM Stubs
|
|
---------------------------------------------
|
|
If CONFIG_ROM_STUBS is defined, the debug breakpoint and single step
|
|
entries in the vector table are restored to their initial values
|
|
immediately _after_ initializing the vector table. Defining this macro
|
|
is useful when ROM-based stubs are implemented.
|
|
|
|
NOTE: The default GERMS monitor does NOT implement gdb stubs, nor does
|
|
it initialize the vector table. Therefore, when debugging U-Boot, you
|
|
should NOT set a software breakpoint prior to vector table initialization.
|
|
|
|
5.2 Starting a Debug Session
|
|
----------------------------
|
|
If you're not familiar with gdb, you follow these step-by-step instructions.
|
|
These instructions are NOT the only way to start a debug session, but they
|
|
cover most of the individual functions to get you started.
|
|
|
|
1. Start the JTAG gdb server. Open a Nios shell window and start
|
|
the server. When the server is started you must provide the base
|
|
address of the OCI core. For example, when using the Cyclone
|
|
development kit (DK1C20):
|
|
|
|
$ nios-gdb-server --ocibase=0x00920800 --tcpport=2342
|
|
|
|
2. Start gdb. Open a Nios shell window, change to the top-level
|
|
U-Boot directory and start gdb, specifying the u-boot elf file:
|
|
|
|
$ nios-elf-gdb u-boot
|
|
|
|
3. Update target settings. From the file menu, select
|
|
"Target Settings ..." and select the following, then click 'Ok':
|
|
|
|
Target: Remote/TCP
|
|
Port : 2342 (same as in step 1)
|
|
Display download dialog: checked
|
|
All other check boxes: unchecked
|
|
|
|
4. Connect to the target. Select menu: 'Run->Connect to target'.
|
|
You should see a dialog box indicating the you successfully connected
|
|
to the target.
|
|
|
|
5. Download U-Boot. Select menu: 'Run->Download'.
|
|
|
|
6. Open a gdb console window and set the source directory paths.
|
|
Select menu: 'View->Console'. In the console window, enter the
|
|
following commands, then close the console window:
|
|
|
|
(gdb) directory common
|
|
(gdb) directory cpu/nios
|
|
(gdb) directory lib_nios
|
|
(gdb) directory board/altera/dk1c20
|
|
|
|
Note that the last command is for the DK1C20 board only. If you
|
|
are using another board, specify that board's directory.
|
|
|
|
7. Open the file board.c (using the file menu in the lower
|
|
left hand corner). Scroll to the board_init() routine and set
|
|
a breakpoint.
|
|
|
|
8. Run U-Boot. Just click on the run icon, or select menu:
|
|
'Run->Run'. U-Boot should start running, then break at your
|
|
breakpoint.
|
|
|
|
9. Have fun & start learning more about gdb.
|
|
|
|
|
|
5.3 For advanced Users
|
|
----------------------
|
|
A few notes for those more familiar with gdb.
|
|
|
|
-Serial port stubs are not implemented. Sorry, but it's just not
|
|
worth _my_ effort. The JTAG stubs work great and are ridiculously
|
|
simple to implement.
|
|
|
|
-If you need to debug the early startup code (prior to the vector
|
|
table initialization), use the nios-console debugger.
|
|
|
|
- Connect, download & run -- there are some problems here. Connect
|
|
download and run seperately to avoid trouble.
|
|
|
|
6. BRAIN DAMAGE
|
|
----------------
|
|
|
|
This section describes some of the unfortunate and avoidable aspects
|
|
of working with the Nios CPU ... and some things you can do to
|
|
reduce your pain.
|
|
|
|
6.1 GERMS doesn't work with Hyperterminal
|
|
------------------------------------------
|
|
GERMS doesn't do CR/LF mapping that is compatible with Hyperterminal
|
|
(or minicom) -- geez. Regardless of you opion of Hyperterminal, this
|
|
sad design decision is remedied by using U-Boot.
|
|
|
|
6.2 cygwin Incompatibility
|
|
---------------------------
|
|
The version of cygwin distributed with the nios GNUPro toolchain is
|
|
out-of-date and incompatible with the latest cygwin distributions.
|
|
In addition, many of the standard utilities are very dated as well.
|
|
If you try to download and build the lastest version of grep for
|
|
example, you'll quickly realize that a native gcc is not available
|
|
(the next topic) which leads to U-Boot build problems (following
|
|
topic).
|
|
|
|
The solution ... well, you can wait for Altera ... or build as
|
|
set of tools for linux.
|
|
|
|
6.3 No native gcc
|
|
------------------
|
|
I'm not sure how this one slipped through the cracks ... but it is
|
|
a real pain. Basically, if you want to build anything for the native
|
|
environment -- forget it! A native (cygwin) gcc is not distributed,
|
|
and the old version of cygwin makes locating one challenging.
|
|
|
|
The solution ... same as above. Just download the gcc source from
|
|
Altera and build up a set of cross tools for your favorite linux
|
|
distro. Anybody who wants to use an already precompiled NIOS cross
|
|
toolchain can it found in the CDK4NIOS project hosted by Source
|
|
Forge at http://cdk4nios.sourceforge.net.
|
|
|
|
6.4 Can't build default U-Boot
|
|
-------------------------------
|
|
By default, when you build U-Boot you will be building some native
|
|
tools along with the target elf, bin, and srec files. Without a
|
|
native gcc, this (obviously) causes problems.
|
|
|
|
For developers using the Altera cygwin tools you can remove the
|
|
'tools' directory from SUBDIRS in the top-level Makefile. You will
|
|
also have to edit common/Makefile:
|
|
|
|
Replace:
|
|
env_embedded.o: env_embedded.c ../tools/envcrc
|
|
$(CC) $(AFLAGS) -Wa,--no-warn \
|
|
-DENV_CRC=$(shell ../tools/envcrc) \
|
|
-c -o $@ env_embedded.c
|
|
|
|
With:
|
|
env_embedded.o: env_embedded.c
|
|
$(CC) $(AFLAGS) -Wa,--no-warn \
|
|
-DENV_CRC=0 \
|
|
-c -o $@ env_embedded.c
|
|
|
|
BTW, thats a 'zero' ... not the letter 'O'. And not that the
|
|
"../tools/envcrc" dependency is removed.
|
|
|
|
|
|
7. HELP WANTED
|
|
---------------
|
|
|
|
There are plenty of areas where help is needed. Here's are some ideas
|
|
for those interested in contributing:
|
|
|
|
-CompactFlash. Port & test CF/FAT.
|
|
|
|
-Bedbug. Develop bedbug for Nios ... or at least provide a disassemble
|
|
command.
|
|
|
|
-Add boot support for ucLinux (niosnommu).
|
|
|
|
-Implement (don't copy Altera code) the __mulxx routines using the
|
|
MSTEP and MUL instructions (e.g. CONFIG_SYS_NIOS_MULT_HW and CONFIG_SYS_NIOS_MULT_MSTEP).
|
|
|
|
|
|
Regards,
|
|
|
|
--Scott
|
|
<smcnutt@psyent.com>
|
|
|
|
--Stephan
|
|
<linz@li-pro.net>
|