mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-17 07:28:51 +09:00
![]() Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com> |
||
---|---|---|
.. | ||
ddr.c | ||
Kconfig | ||
law.c | ||
MAINTAINERS | ||
Makefile | ||
mpc8572ds.c | ||
README | ||
tlb.c |
Overview -------- MPC8572DS is a high-performance computing, evaluation and development platform supporting the mpc8572 PowerTM processor. Building U-Boot ----------- make MPC8572DS_config make Flash Banks ----------- MPC8572DS board has two flash banks. They are both present on boot, but their locations can be swapped using the dip-switch SW9[1:2]. Booting is always from the boot bank at 0xec00_0000. Memory Map ---------- 0xe800_0000 - 0xebff_ffff Alternate bank 64MB 0xec00_0000 - 0xefff_ffff Boot bank 64MB 0xebf8_0000 - 0xebff_ffff Alternate U-Boot address 512KB 0xeff8_0000 - 0xefff_ffff Boot U-Boot address 512KB Flashing Images --------------- To place a new U-Boot image in the alternate flash bank and then reset with that new image temporarily, use this: tftp 1000000 u-boot.bin erase ebf80000 ebffffff cp.b 1000000 ebf80000 80000 pixis_reset altbank To program the image in the boot flash bank: tftp 1000000 u-boot.bin protect off all erase eff80000 ffffffff cp.b 1000000 eff80000 80000 The pixis_reset command ----------------------- The command - "pixis_reset", is introduced to reset mpc8572ds board using the FPGA sequencer. When the board restarts, it has the option of using either the current or alternate flash bank as the boot image, with or without the watchdog timer enabled, and finally with or without frequency changes. Usage is; pixis_reset pixis_reset altbank pixis_reset altbank wd pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio> pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio> Examples: /* reset to current bank, like "reset" command */ pixis_reset /* reset board but use the to alternate flash bank */ pixis_reset altbank Using the Device Tree Source File --------------------------------- To create the DTB (Device Tree Binary) image file, use a command similar to this: dtc -b 0 -f -I dts -O dtb mpc8572ds.dts > mpc8572ds.dtb Likely, that .dts file will come from here; linux-2.6/arch/powerpc/boot/dts/mpc8572ds.dts Booting Linux ------------- Place a linux uImage in the TFTP disk area. tftp 1000000 uImage.8572 tftp c00000 mpc8572ds.dtb bootm 1000000 - c00000 Implementing AMP(Asymmetric MultiProcessing) ------------- 1. Build kernel image for core0: a. $ make 85xx/mpc8572_ds_defconfig b. $ make menuconfig - un-select "Processor support"->"Symetric multi-processing support" c. $ make uImage d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0 2. Build kernel image for core1: a. $ make 85xx/mpc8572_ds_defconfig b. $ make menuconfig - Un-select "Processor support"->"Symetric multi-processing support" - Select "Advanced setup" -> " Prompt for advanced kernel configuration options" - Select "Set physical address where the kernel is loaded" and set it to 0x20000000, assuming core1 will start from 512MB. - Select "Set custom page offset address" - Select "Set custom kernel base address" - Select "Set maximum low memory" - "Exit" and save the selection. c. $ make uImage d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1 3. Create dtb for core0: $ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb 4. Create dtb for core1: $ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb 5. Bring up two cores separately: a. Power on the board, under U-Boot prompt: => setenv <serverip> => setenv <ipaddr> => setenv bootargs root=/dev/ram rw console=ttyS0,115200 b. Bring up core1's kernel first: => setenv bootm_low 0x20000000 => setenv bootm_size 0x10000000 => tftp 21000000 8572/uImage.core1 => tftp 22000000 8572/ramdiskfile => tftp 20c00000 8572/mpc8572ds_core1.dtb => interrupts off => bootm start 21000000 22000000 20c00000 => bootm loados => bootm ramdisk => bootm fdt => fdt boardsetup => fdt chosen $initrd_start $initrd_end => bootm prep => cpu 1 release $bootm_low - $fdtaddr - c. Bring up core0's kernel(on the same U-Boot console): => setenv bootm_low 0 => setenv bootm_size 0x20000000 => tftp 1000000 8572/uImage.core0 => tftp 2000000 8572/ramdiskfile => tftp c00000 8572/mpc8572ds_core0.dtb => bootm 1000000 2000000 c00000 Please note only core0 will run U-Boot, core1 starts kernel directly after "cpu release" command is issued.