u-boot-brain/drivers/i2c/mxc_i2c.c
Alison Wang 30ea41a489 I2C: mxc_i2c: Add support for Vybrid VF610 platform
This patch adds support for Vybrid VF610 platform.

There are some differences between i.MX6 and Vybrid for I2C controller.
(1) The registers' offset are different.
(2) The I2C clock divider values are different.
(3) In I2C control register, the enable/disable/reset bit is inverted for Vybrid comparing to i.MX6.
(4) In I2C status register, the interrupt flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".
(5) In I2C status register, the arbitration lost flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".

Signed-off-by: Alison Wang <b18965@freescale.com>
2013-07-23 08:34:57 +02:00

549 lines
13 KiB
C

/*
* i2c driver for Freescale i.MX series
*
* (c) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de>
* (c) 2011 Marek Vasut <marek.vasut@gmail.com>
*
* Based on i2c-imx.c from linux kernel:
* Copyright (C) 2005 Torsten Koschorrek <koschorrek at synertronixx.de>
* Copyright (C) 2005 Matthias Blaschke <blaschke at synertronixx.de>
* Copyright (C) 2007 RightHand Technologies, Inc.
* Copyright (C) 2008 Darius Augulis <darius.augulis at teltonika.lt>
*
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/errno.h>
#include <asm/io.h>
#include <i2c.h>
#include <watchdog.h>
#ifdef I2C_QUIRK_REG
struct mxc_i2c_regs {
uint8_t iadr;
uint8_t ifdr;
uint8_t i2cr;
uint8_t i2sr;
uint8_t i2dr;
};
#else
struct mxc_i2c_regs {
uint32_t iadr;
uint32_t ifdr;
uint32_t i2cr;
uint32_t i2sr;
uint32_t i2dr;
};
#endif
#define I2CR_IIEN (1 << 6)
#define I2CR_MSTA (1 << 5)
#define I2CR_MTX (1 << 4)
#define I2CR_TX_NO_AK (1 << 3)
#define I2CR_RSTA (1 << 2)
#define I2SR_ICF (1 << 7)
#define I2SR_IBB (1 << 5)
#define I2SR_IAL (1 << 4)
#define I2SR_IIF (1 << 1)
#define I2SR_RX_NO_AK (1 << 0)
#ifdef I2C_QUIRK_REG
#define I2CR_IEN (0 << 7)
#define I2CR_IDIS (1 << 7)
#define I2SR_IIF_CLEAR (1 << 1)
#else
#define I2CR_IEN (1 << 7)
#define I2CR_IDIS (0 << 7)
#define I2SR_IIF_CLEAR (0 << 1)
#endif
#if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE)
#error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver"
#endif
#ifdef I2C_QUIRK_REG
static u16 i2c_clk_div[60][2] = {
{ 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 },
{ 28, 0x04 }, { 30, 0x05 }, { 32, 0x09 }, { 34, 0x06 },
{ 36, 0x0A }, { 40, 0x07 }, { 44, 0x0C }, { 48, 0x0D },
{ 52, 0x43 }, { 56, 0x0E }, { 60, 0x45 }, { 64, 0x12 },
{ 68, 0x0F }, { 72, 0x13 }, { 80, 0x14 }, { 88, 0x15 },
{ 96, 0x19 }, { 104, 0x16 }, { 112, 0x1A }, { 128, 0x17 },
{ 136, 0x4F }, { 144, 0x1C }, { 160, 0x1D }, { 176, 0x55 },
{ 192, 0x1E }, { 208, 0x56 }, { 224, 0x22 }, { 228, 0x24 },
{ 240, 0x1F }, { 256, 0x23 }, { 288, 0x5C }, { 320, 0x25 },
{ 384, 0x26 }, { 448, 0x2A }, { 480, 0x27 }, { 512, 0x2B },
{ 576, 0x2C }, { 640, 0x2D }, { 768, 0x31 }, { 896, 0x32 },
{ 960, 0x2F }, { 1024, 0x33 }, { 1152, 0x34 }, { 1280, 0x35 },
{ 1536, 0x36 }, { 1792, 0x3A }, { 1920, 0x37 }, { 2048, 0x3B },
{ 2304, 0x3C }, { 2560, 0x3D }, { 3072, 0x3E }, { 3584, 0x7A },
{ 3840, 0x3F }, { 4096, 0x7B }, { 5120, 0x7D }, { 6144, 0x7E },
};
#else
static u16 i2c_clk_div[50][2] = {
{ 22, 0x20 }, { 24, 0x21 }, { 26, 0x22 }, { 28, 0x23 },
{ 30, 0x00 }, { 32, 0x24 }, { 36, 0x25 }, { 40, 0x26 },
{ 42, 0x03 }, { 44, 0x27 }, { 48, 0x28 }, { 52, 0x05 },
{ 56, 0x29 }, { 60, 0x06 }, { 64, 0x2A }, { 72, 0x2B },
{ 80, 0x2C }, { 88, 0x09 }, { 96, 0x2D }, { 104, 0x0A },
{ 112, 0x2E }, { 128, 0x2F }, { 144, 0x0C }, { 160, 0x30 },
{ 192, 0x31 }, { 224, 0x32 }, { 240, 0x0F }, { 256, 0x33 },
{ 288, 0x10 }, { 320, 0x34 }, { 384, 0x35 }, { 448, 0x36 },
{ 480, 0x13 }, { 512, 0x37 }, { 576, 0x14 }, { 640, 0x38 },
{ 768, 0x39 }, { 896, 0x3A }, { 960, 0x17 }, { 1024, 0x3B },
{ 1152, 0x18 }, { 1280, 0x3C }, { 1536, 0x3D }, { 1792, 0x3E },
{ 1920, 0x1B }, { 2048, 0x3F }, { 2304, 0x1C }, { 2560, 0x1D },
{ 3072, 0x1E }, { 3840, 0x1F }
};
#endif
/*
* Calculate and set proper clock divider
*/
static uint8_t i2c_imx_get_clk(unsigned int rate)
{
unsigned int i2c_clk_rate;
unsigned int div;
u8 clk_div;
#if defined(CONFIG_MX31)
struct clock_control_regs *sc_regs =
(struct clock_control_regs *)CCM_BASE;
/* start the required I2C clock */
writel(readl(&sc_regs->cgr0) | (3 << CONFIG_SYS_I2C_CLK_OFFSET),
&sc_regs->cgr0);
#endif
/* Divider value calculation */
i2c_clk_rate = mxc_get_clock(MXC_I2C_CLK);
div = (i2c_clk_rate + rate - 1) / rate;
if (div < i2c_clk_div[0][0])
clk_div = 0;
else if (div > i2c_clk_div[ARRAY_SIZE(i2c_clk_div) - 1][0])
clk_div = ARRAY_SIZE(i2c_clk_div) - 1;
else
for (clk_div = 0; i2c_clk_div[clk_div][0] < div; clk_div++)
;
/* Store divider value */
return clk_div;
}
/*
* Set I2C Bus speed
*/
static int bus_i2c_set_bus_speed(void *base, int speed)
{
struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base;
u8 clk_idx = i2c_imx_get_clk(speed);
u8 idx = i2c_clk_div[clk_idx][1];
/* Store divider value */
writeb(idx, &i2c_regs->ifdr);
/* Reset module */
writeb(I2CR_IDIS, &i2c_regs->i2cr);
writeb(0, &i2c_regs->i2sr);
return 0;
}
/*
* Get I2C Speed
*/
static unsigned int bus_i2c_get_bus_speed(void *base)
{
struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base;
u8 clk_idx = readb(&i2c_regs->ifdr);
u8 clk_div;
for (clk_div = 0; i2c_clk_div[clk_div][1] != clk_idx; clk_div++)
;
return mxc_get_clock(MXC_I2C_CLK) / i2c_clk_div[clk_div][0];
}
#define ST_BUS_IDLE (0 | (I2SR_IBB << 8))
#define ST_BUS_BUSY (I2SR_IBB | (I2SR_IBB << 8))
#define ST_IIF (I2SR_IIF | (I2SR_IIF << 8))
static int wait_for_sr_state(struct mxc_i2c_regs *i2c_regs, unsigned state)
{
unsigned sr;
ulong elapsed;
ulong start_time = get_timer(0);
for (;;) {
sr = readb(&i2c_regs->i2sr);
if (sr & I2SR_IAL) {
#ifdef I2C_QUIRK_REG
writeb(sr | I2SR_IAL, &i2c_regs->i2sr);
#else
writeb(sr & ~I2SR_IAL, &i2c_regs->i2sr);
#endif
printf("%s: Arbitration lost sr=%x cr=%x state=%x\n",
__func__, sr, readb(&i2c_regs->i2cr), state);
return -ERESTART;
}
if ((sr & (state >> 8)) == (unsigned char)state)
return sr;
WATCHDOG_RESET();
elapsed = get_timer(start_time);
if (elapsed > (CONFIG_SYS_HZ / 10)) /* .1 seconds */
break;
}
printf("%s: failed sr=%x cr=%x state=%x\n", __func__,
sr, readb(&i2c_regs->i2cr), state);
return -ETIMEDOUT;
}
static int tx_byte(struct mxc_i2c_regs *i2c_regs, u8 byte)
{
int ret;
writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr);
writeb(byte, &i2c_regs->i2dr);
ret = wait_for_sr_state(i2c_regs, ST_IIF);
if (ret < 0)
return ret;
if (ret & I2SR_RX_NO_AK)
return -ENODEV;
return 0;
}
/*
* Stop I2C transaction
*/
static void i2c_imx_stop(struct mxc_i2c_regs *i2c_regs)
{
int ret;
unsigned int temp = readb(&i2c_regs->i2cr);
temp &= ~(I2CR_MSTA | I2CR_MTX);
writeb(temp, &i2c_regs->i2cr);
ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE);
if (ret < 0)
printf("%s:trigger stop failed\n", __func__);
}
/*
* Send start signal, chip address and
* write register address
*/
static int i2c_init_transfer_(struct mxc_i2c_regs *i2c_regs,
uchar chip, uint addr, int alen)
{
unsigned int temp;
int ret;
/* Enable I2C controller */
#ifdef I2C_QUIRK_REG
if (readb(&i2c_regs->i2cr) & I2CR_IDIS) {
#else
if (!(readb(&i2c_regs->i2cr) & I2CR_IEN)) {
#endif
writeb(I2CR_IEN, &i2c_regs->i2cr);
/* Wait for controller to be stable */
udelay(50);
}
if (readb(&i2c_regs->iadr) == (chip << 1))
writeb((chip << 1) ^ 2, &i2c_regs->iadr);
writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr);
ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE);
if (ret < 0)
return ret;
/* Start I2C transaction */
temp = readb(&i2c_regs->i2cr);
temp |= I2CR_MSTA;
writeb(temp, &i2c_regs->i2cr);
ret = wait_for_sr_state(i2c_regs, ST_BUS_BUSY);
if (ret < 0)
return ret;
temp |= I2CR_MTX | I2CR_TX_NO_AK;
writeb(temp, &i2c_regs->i2cr);
/* write slave address */
ret = tx_byte(i2c_regs, chip << 1);
if (ret < 0)
return ret;
while (alen--) {
ret = tx_byte(i2c_regs, (addr >> (alen * 8)) & 0xff);
if (ret < 0)
return ret;
}
return 0;
}
static int i2c_idle_bus(void *base);
static int i2c_init_transfer(struct mxc_i2c_regs *i2c_regs,
uchar chip, uint addr, int alen)
{
int retry;
int ret;
for (retry = 0; retry < 3; retry++) {
ret = i2c_init_transfer_(i2c_regs, chip, addr, alen);
if (ret >= 0)
return 0;
i2c_imx_stop(i2c_regs);
if (ret == -ENODEV)
return ret;
printf("%s: failed for chip 0x%x retry=%d\n", __func__, chip,
retry);
if (ret != -ERESTART)
/* Disable controller */
writeb(I2CR_IDIS, &i2c_regs->i2cr);
udelay(100);
if (i2c_idle_bus(i2c_regs) < 0)
break;
}
printf("%s: give up i2c_regs=%p\n", __func__, i2c_regs);
return ret;
}
/*
* Read data from I2C device
*/
int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf,
int len)
{
int ret;
unsigned int temp;
int i;
struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base;
ret = i2c_init_transfer(i2c_regs, chip, addr, alen);
if (ret < 0)
return ret;
temp = readb(&i2c_regs->i2cr);
temp |= I2CR_RSTA;
writeb(temp, &i2c_regs->i2cr);
ret = tx_byte(i2c_regs, (chip << 1) | 1);
if (ret < 0) {
i2c_imx_stop(i2c_regs);
return ret;
}
/* setup bus to read data */
temp = readb(&i2c_regs->i2cr);
temp &= ~(I2CR_MTX | I2CR_TX_NO_AK);
if (len == 1)
temp |= I2CR_TX_NO_AK;
writeb(temp, &i2c_regs->i2cr);
writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr);
readb(&i2c_regs->i2dr); /* dummy read to clear ICF */
/* read data */
for (i = 0; i < len; i++) {
ret = wait_for_sr_state(i2c_regs, ST_IIF);
if (ret < 0) {
i2c_imx_stop(i2c_regs);
return ret;
}
/*
* It must generate STOP before read I2DR to prevent
* controller from generating another clock cycle
*/
if (i == (len - 1)) {
i2c_imx_stop(i2c_regs);
} else if (i == (len - 2)) {
temp = readb(&i2c_regs->i2cr);
temp |= I2CR_TX_NO_AK;
writeb(temp, &i2c_regs->i2cr);
}
writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr);
buf[i] = readb(&i2c_regs->i2dr);
}
i2c_imx_stop(i2c_regs);
return 0;
}
/*
* Write data to I2C device
*/
int bus_i2c_write(void *base, uchar chip, uint addr, int alen,
const uchar *buf, int len)
{
int ret;
int i;
struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base;
ret = i2c_init_transfer(i2c_regs, chip, addr, alen);
if (ret < 0)
return ret;
for (i = 0; i < len; i++) {
ret = tx_byte(i2c_regs, buf[i]);
if (ret < 0)
break;
}
i2c_imx_stop(i2c_regs);
return ret;
}
struct i2c_parms {
void *base;
void *idle_bus_data;
int (*idle_bus_fn)(void *p);
};
struct sram_data {
unsigned curr_i2c_bus;
struct i2c_parms i2c_data[3];
};
/*
* For SPL boot some boards need i2c before SDRAM is initialized so force
* variables to live in SRAM
*/
static struct sram_data __attribute__((section(".data"))) srdata;
void *get_base(void)
{
#ifdef CONFIG_SYS_I2C_BASE
#ifdef CONFIG_I2C_MULTI_BUS
void *ret = srdata.i2c_data[srdata.curr_i2c_bus].base;
if (ret)
return ret;
#endif
return (void *)CONFIG_SYS_I2C_BASE;
#elif defined(CONFIG_I2C_MULTI_BUS)
return srdata.i2c_data[srdata.curr_i2c_bus].base;
#else
return srdata.i2c_data[0].base;
#endif
}
static struct i2c_parms *i2c_get_parms(void *base)
{
int i = 0;
struct i2c_parms *p = srdata.i2c_data;
while (i < ARRAY_SIZE(srdata.i2c_data)) {
if (p->base == base)
return p;
p++;
i++;
}
printf("Invalid I2C base: %p\n", base);
return NULL;
}
static int i2c_idle_bus(void *base)
{
struct i2c_parms *p = i2c_get_parms(base);
if (p && p->idle_bus_fn)
return p->idle_bus_fn(p->idle_bus_data);
return 0;
}
#ifdef CONFIG_I2C_MULTI_BUS
unsigned int i2c_get_bus_num(void)
{
return srdata.curr_i2c_bus;
}
int i2c_set_bus_num(unsigned bus_idx)
{
if (bus_idx >= ARRAY_SIZE(srdata.i2c_data))
return -1;
if (!srdata.i2c_data[bus_idx].base)
return -1;
srdata.curr_i2c_bus = bus_idx;
return 0;
}
#endif
int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len)
{
return bus_i2c_read(get_base(), chip, addr, alen, buf, len);
}
int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len)
{
return bus_i2c_write(get_base(), chip, addr, alen, buf, len);
}
/*
* Test if a chip at a given address responds (probe the chip)
*/
int i2c_probe(uchar chip)
{
return bus_i2c_write(get_base(), chip, 0, 0, NULL, 0);
}
void bus_i2c_init(void *base, int speed, int unused,
int (*idle_bus_fn)(void *p), void *idle_bus_data)
{
int i = 0;
struct i2c_parms *p = srdata.i2c_data;
if (!base)
return;
for (;;) {
if (!p->base || (p->base == base)) {
p->base = base;
if (idle_bus_fn) {
p->idle_bus_fn = idle_bus_fn;
p->idle_bus_data = idle_bus_data;
}
break;
}
p++;
i++;
if (i >= ARRAY_SIZE(srdata.i2c_data))
return;
}
bus_i2c_set_bus_speed(base, speed);
}
/*
* Init I2C Bus
*/
void i2c_init(int speed, int unused)
{
bus_i2c_init(get_base(), speed, unused, NULL, NULL);
}
/*
* Set I2C Speed
*/
int i2c_set_bus_speed(unsigned int speed)
{
return bus_i2c_set_bus_speed(get_base(), speed);
}
/*
* Get I2C Speed
*/
unsigned int i2c_get_bus_speed(void)
{
return bus_i2c_get_bus_speed(get_base());
}