u-boot-brain/drivers/mmc/meson_gx_mmc.c
Neil Armstrong 0dbb54eb32 mmc: meson-gx: change clock phase value on SM1 SoCs
Amlogic SM1 SoCs doesn't work over 50MHz. When phase sets to 270', it's
working fine over 50MHz on Amlogic SM1 SoCs.
Since Other Amlogic SoCs doens't report an issue, phase value is using
to 180' by default.

To distinguish which value is used adds an u-boot only sm1 compatible.

In future, it needs to find what value is a proper about each SoCs.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
2020-11-12 14:31:29 +01:00

379 lines
9.0 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2016 Carlo Caione <carlo@caione.org>
*/
#include <common.h>
#include <clk.h>
#include <cpu_func.h>
#include <dm.h>
#include <fdtdec.h>
#include <malloc.h>
#include <pwrseq.h>
#include <mmc.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <linux/delay.h>
#include <linux/log2.h>
#include "meson_gx_mmc.h"
bool meson_gx_mmc_is_compatible(struct udevice *dev,
enum meson_gx_mmc_compatible family)
{
enum meson_gx_mmc_compatible compat = dev_get_driver_data(dev);
return compat == family;
}
static inline void *get_regbase(const struct mmc *mmc)
{
struct meson_mmc_platdata *pdata = mmc->priv;
return pdata->regbase;
}
static inline uint32_t meson_read(struct mmc *mmc, int offset)
{
return readl(get_regbase(mmc) + offset);
}
static inline void meson_write(struct mmc *mmc, uint32_t val, int offset)
{
writel(val, get_regbase(mmc) + offset);
}
static void meson_mmc_config_clock(struct mmc *mmc)
{
uint32_t meson_mmc_clk = 0;
unsigned int clk, clk_src, clk_div;
if (!mmc->clock)
return;
/* TOFIX This should use the proper clock taken from DT */
/* 1GHz / CLK_MAX_DIV = 15,9 MHz */
if (mmc->clock > 16000000) {
clk = SD_EMMC_CLKSRC_DIV2;
clk_src = CLK_SRC_DIV2;
} else {
clk = SD_EMMC_CLKSRC_24M;
clk_src = CLK_SRC_24M;
}
clk_div = DIV_ROUND_UP(clk, mmc->clock);
/*
* SM1 SoCs doesn't work fine over 50MHz with CLK_CO_PHASE_180
* If CLK_CO_PHASE_270 is used, it's more stable than other.
* Other SoCs use CLK_CO_PHASE_180 by default.
* It needs to find what is a proper value about each SoCs.
*/
if (meson_gx_mmc_is_compatible(mmc->dev, MMC_COMPATIBLE_SM1))
meson_mmc_clk |= CLK_CO_PHASE_270;
else
meson_mmc_clk |= CLK_CO_PHASE_180;
/* 180 phase tx clock */
meson_mmc_clk |= CLK_TX_PHASE_000;
/* clock settings */
meson_mmc_clk |= clk_src;
meson_mmc_clk |= clk_div;
meson_write(mmc, meson_mmc_clk, MESON_SD_EMMC_CLOCK);
}
static int meson_dm_mmc_set_ios(struct udevice *dev)
{
struct mmc *mmc = mmc_get_mmc_dev(dev);
uint32_t meson_mmc_cfg;
meson_mmc_config_clock(mmc);
meson_mmc_cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
meson_mmc_cfg &= ~CFG_BUS_WIDTH_MASK;
if (mmc->bus_width == 1)
meson_mmc_cfg |= CFG_BUS_WIDTH_1;
else if (mmc->bus_width == 4)
meson_mmc_cfg |= CFG_BUS_WIDTH_4;
else if (mmc->bus_width == 8)
meson_mmc_cfg |= CFG_BUS_WIDTH_8;
else
return -EINVAL;
/* 512 bytes block length */
meson_mmc_cfg &= ~CFG_BL_LEN_MASK;
meson_mmc_cfg |= CFG_BL_LEN_512;
/* Response timeout 256 clk */
meson_mmc_cfg &= ~CFG_RESP_TIMEOUT_MASK;
meson_mmc_cfg |= CFG_RESP_TIMEOUT_256;
/* Command-command gap 16 clk */
meson_mmc_cfg &= ~CFG_RC_CC_MASK;
meson_mmc_cfg |= CFG_RC_CC_16;
meson_write(mmc, meson_mmc_cfg, MESON_SD_EMMC_CFG);
return 0;
}
static void meson_mmc_setup_cmd(struct mmc *mmc, struct mmc_data *data,
struct mmc_cmd *cmd)
{
uint32_t meson_mmc_cmd = 0, cfg;
meson_mmc_cmd |= cmd->cmdidx << CMD_CFG_CMD_INDEX_SHIFT;
if (cmd->resp_type & MMC_RSP_PRESENT) {
if (cmd->resp_type & MMC_RSP_136)
meson_mmc_cmd |= CMD_CFG_RESP_128;
if (cmd->resp_type & MMC_RSP_BUSY)
meson_mmc_cmd |= CMD_CFG_R1B;
if (!(cmd->resp_type & MMC_RSP_CRC))
meson_mmc_cmd |= CMD_CFG_RESP_NOCRC;
} else {
meson_mmc_cmd |= CMD_CFG_NO_RESP;
}
if (data) {
cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
cfg &= ~CFG_BL_LEN_MASK;
cfg |= ilog2(data->blocksize) << CFG_BL_LEN_SHIFT;
meson_write(mmc, cfg, MESON_SD_EMMC_CFG);
if (data->flags == MMC_DATA_WRITE)
meson_mmc_cmd |= CMD_CFG_DATA_WR;
meson_mmc_cmd |= CMD_CFG_DATA_IO | CMD_CFG_BLOCK_MODE |
data->blocks;
}
meson_mmc_cmd |= CMD_CFG_TIMEOUT_4S | CMD_CFG_OWNER |
CMD_CFG_END_OF_CHAIN;
meson_write(mmc, meson_mmc_cmd, MESON_SD_EMMC_CMD_CFG);
}
static void meson_mmc_setup_addr(struct mmc *mmc, struct mmc_data *data)
{
struct meson_mmc_platdata *pdata = mmc->priv;
unsigned int data_size;
uint32_t data_addr = 0;
if (data) {
data_size = data->blocks * data->blocksize;
if (data->flags == MMC_DATA_READ) {
data_addr = (ulong) data->dest;
invalidate_dcache_range(data_addr,
data_addr + data_size);
} else {
pdata->w_buf = calloc(data_size, sizeof(char));
data_addr = (ulong) pdata->w_buf;
memcpy(pdata->w_buf, data->src, data_size);
flush_dcache_range(data_addr, data_addr + data_size);
}
}
meson_write(mmc, data_addr, MESON_SD_EMMC_CMD_DAT);
}
static void meson_mmc_read_response(struct mmc *mmc, struct mmc_cmd *cmd)
{
if (cmd->resp_type & MMC_RSP_136) {
cmd->response[0] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP3);
cmd->response[1] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP2);
cmd->response[2] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP1);
cmd->response[3] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP);
} else {
cmd->response[0] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP);
}
}
static int meson_dm_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
struct mmc_data *data)
{
struct mmc *mmc = mmc_get_mmc_dev(dev);
struct meson_mmc_platdata *pdata = mmc->priv;
uint32_t status;
ulong start;
int ret = 0;
/* max block size supported by chip is 512 byte */
if (data && data->blocksize > 512)
return -EINVAL;
meson_mmc_setup_cmd(mmc, data, cmd);
meson_mmc_setup_addr(mmc, data);
meson_write(mmc, cmd->cmdarg, MESON_SD_EMMC_CMD_ARG);
/* use 10s timeout */
start = get_timer(0);
do {
status = meson_read(mmc, MESON_SD_EMMC_STATUS);
} while(!(status & STATUS_END_OF_CHAIN) && get_timer(start) < 10000);
if (!(status & STATUS_END_OF_CHAIN))
ret = -ETIMEDOUT;
else if (status & STATUS_RESP_TIMEOUT)
ret = -ETIMEDOUT;
else if (status & STATUS_ERR_MASK)
ret = -EIO;
meson_mmc_read_response(mmc, cmd);
if (data && data->flags == MMC_DATA_WRITE)
free(pdata->w_buf);
/* reset status bits */
meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
return ret;
}
static const struct dm_mmc_ops meson_dm_mmc_ops = {
.send_cmd = meson_dm_mmc_send_cmd,
.set_ios = meson_dm_mmc_set_ios,
};
static int meson_mmc_ofdata_to_platdata(struct udevice *dev)
{
struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
fdt_addr_t addr;
addr = dev_read_addr(dev);
if (addr == FDT_ADDR_T_NONE)
return -EINVAL;
pdata->regbase = (void *)addr;
return 0;
}
static int meson_mmc_probe(struct udevice *dev)
{
struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
struct mmc *mmc = &pdata->mmc;
struct mmc_config *cfg = &pdata->cfg;
struct clk_bulk clocks;
uint32_t val;
int ret;
#ifdef CONFIG_PWRSEQ
struct udevice *pwr_dev;
#endif
/* Enable the clocks feeding the MMC controller */
ret = clk_get_bulk(dev, &clocks);
if (ret)
return ret;
ret = clk_enable_bulk(&clocks);
if (ret)
return ret;
cfg->voltages = MMC_VDD_33_34 | MMC_VDD_32_33 |
MMC_VDD_31_32 | MMC_VDD_165_195;
cfg->host_caps = MMC_MODE_8BIT | MMC_MODE_4BIT |
MMC_MODE_HS_52MHz | MMC_MODE_HS;
cfg->f_min = DIV_ROUND_UP(SD_EMMC_CLKSRC_24M, CLK_MAX_DIV);
cfg->f_max = 100000000; /* 100 MHz */
cfg->b_max = 511; /* max 512 - 1 blocks */
cfg->name = dev->name;
mmc->priv = pdata;
upriv->mmc = mmc;
mmc_set_clock(mmc, cfg->f_min, MMC_CLK_ENABLE);
#ifdef CONFIG_PWRSEQ
/* Enable power if needed */
ret = uclass_get_device_by_phandle(UCLASS_PWRSEQ, dev, "mmc-pwrseq",
&pwr_dev);
if (!ret) {
ret = pwrseq_set_power(pwr_dev, true);
if (ret)
return ret;
}
#endif
/* reset all status bits */
meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
/* disable interrupts */
meson_write(mmc, 0, MESON_SD_EMMC_IRQ_EN);
/* enable auto clock mode */
val = meson_read(mmc, MESON_SD_EMMC_CFG);
val &= ~CFG_SDCLK_ALWAYS_ON;
val |= CFG_AUTO_CLK;
meson_write(mmc, val, MESON_SD_EMMC_CFG);
return 0;
}
int meson_mmc_bind(struct udevice *dev)
{
struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
return mmc_bind(dev, &pdata->mmc, &pdata->cfg);
}
static const struct udevice_id meson_mmc_match[] = {
{ .compatible = "amlogic,meson-gx-mmc", .data = MMC_COMPATIBLE_GX },
{ .compatible = "amlogic,meson-axg-mmc", .data = MMC_COMPATIBLE_GX },
{ .compatible = "amlogic,meson-sm1-mmc", .data = MMC_COMPATIBLE_SM1 },
{ /* sentinel */ }
};
U_BOOT_DRIVER(meson_mmc) = {
.name = "meson_gx_mmc",
.id = UCLASS_MMC,
.of_match = meson_mmc_match,
.ops = &meson_dm_mmc_ops,
.probe = meson_mmc_probe,
.bind = meson_mmc_bind,
.ofdata_to_platdata = meson_mmc_ofdata_to_platdata,
.platdata_auto_alloc_size = sizeof(struct meson_mmc_platdata),
};
#ifdef CONFIG_PWRSEQ
static int meson_mmc_pwrseq_set_power(struct udevice *dev, bool enable)
{
struct gpio_desc reset;
int ret;
ret = gpio_request_by_name(dev, "reset-gpios", 0, &reset, GPIOD_IS_OUT);
if (ret)
return ret;
dm_gpio_set_value(&reset, 1);
udelay(1);
dm_gpio_set_value(&reset, 0);
udelay(200);
return 0;
}
static const struct pwrseq_ops meson_mmc_pwrseq_ops = {
.set_power = meson_mmc_pwrseq_set_power,
};
static const struct udevice_id meson_mmc_pwrseq_ids[] = {
{ .compatible = "mmc-pwrseq-emmc" },
{ }
};
U_BOOT_DRIVER(meson_mmc_pwrseq_drv) = {
.name = "mmc_pwrseq_emmc",
.id = UCLASS_PWRSEQ,
.of_match = meson_mmc_pwrseq_ids,
.ops = &meson_mmc_pwrseq_ops,
};
#endif