mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-22 01:48:52 +09:00
![Masahiro Yamada](/assets/img/avatar_default.png)
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have the same content. (both just wrap <asm-generic/errno.h>) Replace all include directives for <asm/errno.h> with <linux/errno.h>. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> [trini: Fixup include/clk.] Signed-off-by: Tom Rini <trini@konsulko.com>
233 lines
5.4 KiB
C
233 lines
5.4 KiB
C
/*
|
|
* board/renesas/stout/stout.c
|
|
* This file is Stout board support.
|
|
*
|
|
* Copyright (C) 2015 Renesas Electronics Europe GmbH
|
|
* Copyright (C) 2015 Renesas Electronics Corporation
|
|
* Copyright (C) 2015 Cogent Embedded, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <malloc.h>
|
|
#include <netdev.h>
|
|
#include <dm.h>
|
|
#include <dm/platform_data/serial_sh.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/io.h>
|
|
#include <linux/errno.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/arch/rmobile.h>
|
|
#include <asm/arch/rcar-mstp.h>
|
|
#include <asm/arch/mmc.h>
|
|
#include <asm/arch/sh_sdhi.h>
|
|
#include <miiphy.h>
|
|
#include <i2c.h>
|
|
#include <mmc.h>
|
|
#include "qos.h"
|
|
#include "cpld.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define CLK2MHZ(clk) (clk / 1000 / 1000)
|
|
void s_init(void)
|
|
{
|
|
struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE;
|
|
struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE;
|
|
|
|
/* Watchdog init */
|
|
writel(0xA5A5A500, &rwdt->rwtcsra);
|
|
writel(0xA5A5A500, &swdt->swtcsra);
|
|
|
|
/* CPU frequency setting. Set to 1.4GHz */
|
|
if (rmobile_get_cpu_rev_integer() >= R8A7790_CUT_ES2X) {
|
|
u32 stat = 0;
|
|
u32 stc = ((1400 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1)
|
|
<< PLL0_STC_BIT;
|
|
clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc);
|
|
|
|
do {
|
|
stat = readl(PLLECR) & PLL0ST;
|
|
} while (stat == 0x0);
|
|
}
|
|
|
|
/* QoS(Quality-of-Service) Init */
|
|
qos_init();
|
|
}
|
|
|
|
#define TMU0_MSTP125 (1 << 25)
|
|
#define SCIFA0_MSTP204 (1 << 4)
|
|
#define SDHI0_MSTP314 (1 << 14)
|
|
#define SDHI2_MSTP312 (1 << 12)
|
|
#define ETHER_MSTP813 (1 << 13)
|
|
|
|
#define MSTPSR3 0xE6150048
|
|
#define SMSTPCR3 0xE615013C
|
|
|
|
#define SD2CKCR 0xE6150078
|
|
#define SD2_97500KHZ 0x7
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/* TMU0 */
|
|
mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
|
|
/* SCIFA0 */
|
|
mstp_clrbits_le32(MSTPSR2, SMSTPCR2, SCIFA0_MSTP204);
|
|
/* ETHER */
|
|
mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813);
|
|
/* SDHI0,2 */
|
|
mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SDHI0_MSTP314 | SDHI2_MSTP312);
|
|
|
|
/*
|
|
* SD0 clock is set to 97.5MHz by default.
|
|
* Set SD2 to the 97.5MHz as well.
|
|
*/
|
|
writel(SD2_97500KHZ, SD2CKCR);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
/* Init PFC controller */
|
|
r8a7790_pinmux_init();
|
|
|
|
cpld_init();
|
|
|
|
#ifdef CONFIG_SH_ETHER
|
|
/* ETHER Enable */
|
|
gpio_request(GPIO_FN_ETH_CRS_DV, NULL);
|
|
gpio_request(GPIO_FN_ETH_RX_ER, NULL);
|
|
gpio_request(GPIO_FN_ETH_RXD0, NULL);
|
|
gpio_request(GPIO_FN_ETH_RXD1, NULL);
|
|
gpio_request(GPIO_FN_ETH_LINK, NULL);
|
|
gpio_request(GPIO_FN_ETH_REF_CLK, NULL);
|
|
gpio_request(GPIO_FN_ETH_MDIO, NULL);
|
|
gpio_request(GPIO_FN_ETH_TXD1, NULL);
|
|
gpio_request(GPIO_FN_ETH_TX_EN, NULL);
|
|
gpio_request(GPIO_FN_ETH_MAGIC, NULL);
|
|
gpio_request(GPIO_FN_ETH_TXD0, NULL);
|
|
gpio_request(GPIO_FN_ETH_MDC, NULL);
|
|
gpio_request(GPIO_FN_IRQ1, NULL);
|
|
|
|
gpio_request(GPIO_GP_3_31, NULL); /* PHY_RST */
|
|
gpio_direction_output(GPIO_GP_3_31, 0);
|
|
mdelay(20);
|
|
gpio_set_value(GPIO_GP_3_31, 1);
|
|
udelay(1);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define CXR24 0xEE7003C0 /* MAC address high register */
|
|
#define CXR25 0xEE7003C8 /* MAC address low register */
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int ret = -ENODEV;
|
|
|
|
#ifdef CONFIG_SH_ETHER
|
|
u32 val;
|
|
unsigned char enetaddr[6];
|
|
|
|
ret = sh_eth_initialize(bis);
|
|
if (!eth_getenv_enetaddr("ethaddr", enetaddr))
|
|
return ret;
|
|
|
|
/* Set Mac address */
|
|
val = enetaddr[0] << 24 | enetaddr[1] << 16 |
|
|
enetaddr[2] << 8 | enetaddr[3];
|
|
writel(val, CXR24);
|
|
|
|
val = enetaddr[4] << 8 | enetaddr[5];
|
|
writel(val, CXR25);
|
|
#endif
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* Stout has KSZ8041NL/RNL */
|
|
#define PHY_CONTROL1 0x1E
|
|
#define PHY_LED_MODE 0xC0000
|
|
#define PHY_LED_MODE_ACK 0x4000
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
|
|
ret &= ~PHY_LED_MODE;
|
|
ret |= PHY_LED_MODE_ACK;
|
|
ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
int ret = -ENODEV;
|
|
|
|
#ifdef CONFIG_SH_SDHI
|
|
gpio_request(GPIO_FN_SD0_DAT0, NULL);
|
|
gpio_request(GPIO_FN_SD0_DAT1, NULL);
|
|
gpio_request(GPIO_FN_SD0_DAT2, NULL);
|
|
gpio_request(GPIO_FN_SD0_DAT3, NULL);
|
|
gpio_request(GPIO_FN_SD0_CLK, NULL);
|
|
gpio_request(GPIO_FN_SD0_CMD, NULL);
|
|
gpio_request(GPIO_FN_SD0_CD, NULL);
|
|
gpio_request(GPIO_FN_SD2_DAT0, NULL);
|
|
gpio_request(GPIO_FN_SD2_DAT1, NULL);
|
|
gpio_request(GPIO_FN_SD2_DAT2, NULL);
|
|
gpio_request(GPIO_FN_SD2_DAT3, NULL);
|
|
gpio_request(GPIO_FN_SD2_CLK, NULL);
|
|
gpio_request(GPIO_FN_SD2_CMD, NULL);
|
|
gpio_request(GPIO_FN_SD2_CD, NULL);
|
|
|
|
/* SDHI0 - needs CPLD mux setup */
|
|
gpio_request(GPIO_GP_3_30, NULL);
|
|
gpio_direction_output(GPIO_GP_3_30, 1); /* VLDO3=3.3V */
|
|
gpio_request(GPIO_GP_5_24, NULL);
|
|
gpio_direction_output(GPIO_GP_5_24, 1); /* power on */
|
|
|
|
ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI0_BASE, 0,
|
|
SH_SDHI_QUIRK_16BIT_BUF);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* SDHI2 - needs CPLD mux setup */
|
|
gpio_request(GPIO_GP_3_29, NULL);
|
|
gpio_direction_output(GPIO_GP_3_29, 1); /* VLDO4=3.3V */
|
|
gpio_request(GPIO_GP_5_25, NULL);
|
|
gpio_direction_output(GPIO_GP_5_25, 1); /* power on */
|
|
|
|
ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI2_BASE, 2, 0);
|
|
#endif
|
|
return ret;
|
|
}
|
|
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
|
|
|
|
return 0;
|
|
}
|
|
|
|
const struct rmobile_sysinfo sysinfo = {
|
|
CONFIG_ARCH_RMOBILE_BOARD_STRING
|
|
};
|
|
|
|
static const struct sh_serial_platdata serial_platdata = {
|
|
.base = SCIFA0_BASE,
|
|
.type = PORT_SCIFA,
|
|
.clk = CONFIG_MP_CLK_FREQ,
|
|
};
|
|
|
|
U_BOOT_DEVICE(stout_serials) = {
|
|
.name = "serial_sh",
|
|
.platdata = &serial_platdata,
|
|
};
|