mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-22 01:48:52 +09:00
![tang yuantian](/assets/img/avatar_default.png)
Add deep sleep support on Freescale LS1021QDS platform. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> [York Sun: Fix conflict in fdt.c] Reviewed-by: York Sun <yorksun@freescale.com>
187 lines
4.4 KiB
C
187 lines
4.4 KiB
C
/*
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <fsl_ddr_sdram.h>
|
|
#include <fsl_ddr_dimm_params.h>
|
|
#include <asm/io.h>
|
|
#include "ddr.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
|
ulong ddr_freq;
|
|
|
|
if (ctrl_num > 3) {
|
|
printf("Not supported controller number %d\n", ctrl_num);
|
|
return;
|
|
}
|
|
if (!pdimm->n_ranks)
|
|
return;
|
|
|
|
pbsp = udimms[0];
|
|
|
|
/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
|
|
* freqency and n_banks specified in board_specific_parameters table.
|
|
*/
|
|
ddr_freq = get_ddr_freq(0) / 1000000;
|
|
while (pbsp->datarate_mhz_high) {
|
|
if (pbsp->n_ranks == pdimm->n_ranks) {
|
|
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
|
popts->clk_adjust = pbsp->clk_adjust;
|
|
popts->wrlvl_start = pbsp->wrlvl_start;
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
popts->cpo_override = pbsp->cpo_override;
|
|
popts->write_data_delay =
|
|
pbsp->write_data_delay;
|
|
goto found;
|
|
}
|
|
pbsp_highest = pbsp;
|
|
}
|
|
pbsp++;
|
|
}
|
|
|
|
if (pbsp_highest) {
|
|
printf("Error: board specific timing not found for %lu MT/s\n",
|
|
ddr_freq);
|
|
printf("Trying to use the highest speed (%u) parameters\n",
|
|
pbsp_highest->datarate_mhz_high);
|
|
popts->clk_adjust = pbsp_highest->clk_adjust;
|
|
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
} else {
|
|
panic("DIMM is not supported by this board");
|
|
}
|
|
found:
|
|
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
|
|
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
|
|
|
|
/* force DDR bus width to 32 bits */
|
|
popts->data_bus_width = 1;
|
|
popts->otf_burst_chop_en = 0;
|
|
popts->burst_length = DDR_BL8;
|
|
|
|
/*
|
|
* Factors to consider for half-strength driver enable:
|
|
* - number of DIMMs installed
|
|
*/
|
|
popts->half_strength_driver_enable = 1;
|
|
/*
|
|
* Write leveling override
|
|
*/
|
|
popts->wrlvl_override = 1;
|
|
popts->wrlvl_sample = 0xf;
|
|
|
|
/*
|
|
* Rtt and Rtt_WR override
|
|
*/
|
|
popts->rtt_override = 0;
|
|
|
|
/* Enable ZQ calibration */
|
|
popts->zq_en = 1;
|
|
|
|
#ifdef CONFIG_SYS_FSL_DDR4
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
|
|
DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
|
|
#else
|
|
popts->cswl_override = DDR_CSWL_CS0;
|
|
|
|
/* DHC_EN =1, ODT = 75 Ohm */
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
|
|
#endif
|
|
}
|
|
|
|
#ifdef CONFIG_SYS_DDR_RAW_TIMING
|
|
dimm_params_t ddr_raw_timing = {
|
|
.n_ranks = 1,
|
|
.rank_density = 1073741824u,
|
|
.capacity = 1073741824u,
|
|
.primary_sdram_width = 32,
|
|
.ec_sdram_width = 0,
|
|
.registered_dimm = 0,
|
|
.mirrored_dimm = 0,
|
|
.n_row_addr = 15,
|
|
.n_col_addr = 10,
|
|
.n_banks_per_sdram_device = 8,
|
|
.edc_config = 0,
|
|
.burst_lengths_bitmask = 0x0c,
|
|
|
|
.tckmin_x_ps = 1071,
|
|
.caslat_x = 0xfe << 4, /* 5,6,7,8 */
|
|
.taa_ps = 13125,
|
|
.twr_ps = 15000,
|
|
.trcd_ps = 13125,
|
|
.trrd_ps = 7500,
|
|
.trp_ps = 13125,
|
|
.tras_ps = 37500,
|
|
.trc_ps = 50625,
|
|
.trfc_ps = 160000,
|
|
.twtr_ps = 7500,
|
|
.trtp_ps = 7500,
|
|
.refresh_rate_ps = 7800000,
|
|
.tfaw_ps = 37500,
|
|
};
|
|
|
|
int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
|
|
unsigned int controller_number,
|
|
unsigned int dimm_number)
|
|
{
|
|
static const char dimm_model[] = "Fixed DDR on board";
|
|
|
|
if (((controller_number == 0) && (dimm_number == 0)) ||
|
|
((controller_number == 1) && (dimm_number == 0))) {
|
|
memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
|
|
memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
|
|
memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_DEEP_SLEEP)
|
|
void board_mem_sleep_setup(void)
|
|
{
|
|
void __iomem *qixis_base = (void *)QIXIS_BASE;
|
|
|
|
/* does not provide HW signals for power management */
|
|
clrbits_8(qixis_base + 0x21, 0x2);
|
|
udelay(1);
|
|
}
|
|
#endif
|
|
|
|
phys_size_t initdram(int board_type)
|
|
{
|
|
phys_size_t dram_size;
|
|
|
|
#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
|
|
puts("Initializing DDR....using SPD\n");
|
|
dram_size = fsl_ddr_sdram();
|
|
#else
|
|
dram_size = fsl_ddr_sdram_size();
|
|
#endif
|
|
|
|
#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
|
|
fsl_dp_resume();
|
|
#endif
|
|
|
|
return dram_size;
|
|
}
|
|
|
|
void dram_init_banksize(void)
|
|
{
|
|
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
|
|
gd->bd->bi_dram[0].size = gd->ram_size;
|
|
}
|