u-boot-brain/arch/arm/dts/ca-presidio-engboard.dts
Kate Liu 34a5addb7b board: presidio: Add Parallel NAND support
Set environment for Nand flash (U-boot 2020.04):
- add nand flash in the device tree
- add new default configuration file for G3 using parallel Nand
- set nand parameters in presidio_asic.h

Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-01-18 15:14:37 -05:00

113 lines
2.2 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2020, Cortina Access Inc.
*/
/dts-v1/;
/ {
#address-cells = <2>;
#size-cells = <1>;
mmc0: mmc@f4400000 {
compatible = "cortina,ca-mmc";
reg = <0x0 0xf4400000 0x1000>;
bus-width = <4>;
sd_dll_ctrl = <0xf43200e8>;
io_drv_ctrl = <0xf432004c>;
};
gpio0: gpio-controller@0xf4329280 {
compatible = "cortina,ca-gpio";
reg = <0x0 0xf4329280 0x24>;
gpio-controller;
#gpio-cells = <2>;
status = "okay";
};
gpio1: gpio-controller@0xf43292a4 {
compatible = "cortina,ca-gpio";
reg = <0x0 0xf43292a4 0x24>;
gpio-controller;
#gpio-cells = <2>;
status = "disabled";
};
watchdog: watchdog@0xf432901c {
compatible = "cortina,ca-wdt";
reg = <0x0 0xf432901c 0x34>,
<0x0 0xf4320020 0x04>;
status = "okay";
};
uart0: serial@0xf4329148 {
u-boot,dm-pre-reloc;
compatible = "cortina,ca-uart";
reg = <0x0 0xf4329148 0x30>;
status = "okay";
};
i2c: i2c@f4329120 {
compatible = "cortina,ca-i2c";
reg = <0x0 0xf4329120 0x28>;
clock-frequency = <400000>;
};
nand: nand-controller@f4324000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "cortina,ca-nand";
reg = <0 0xf4324000 0x3b0>, /* NAND controller */
<0 0xf7001000 0xb4>, /* DMA_GLOBAL */
<0 0xf7001a00 0x80>; /* DMA channel0 for FLASH */
status = "okay";
nand-ecc-mode = "hw";
nand-ecc-strength = <16>;
nand-ecc-step-size = <1024>; /* Must be 1024 */
nand_flash_base_addr = <0xe0000000>;
};
sflash: sflash-controller@f4324000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "cortina,ca-sflash";
reg = <0x0 0xf4324000 0x50>;
reg-names = "sflash-regs";
flash@0 {
compatible = "jedec,spi-nor";
spi-rx-bus-width = <1>;
spi-max-frequency = <108000000>;
};
};
leds: led-controller@f43200f0 {
compatible = "cortina,ca-leds";
reg = <0x0 0xf43200f0 0x40>;
cortina,blink-rate1 = <256>;
cortina,blink-rate2 = <512>;
led@0 {
pin = <0>;
active-low;
blink-sel =<0>;
port = <0>;
off-event = <0>;
label = "led0";
};
led@1 {
pin = <1>;
active-low;
blink-sel =<1>;
label = "led1";
};
led@2 {
pin = <2>;
active-low;
label = "led2";
};
};
};