u-boot-brain/arch/x86/cpu/quark/quark.c
Bin Meng 2afb62305e x86: quark: Add PCIe/USB static register programming after memory init
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-16 19:53:52 -06:00

323 lines
8.3 KiB
C

/*
* Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <mmc.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/pci.h>
#include <asm/post.h>
#include <asm/processor.h>
#include <asm/arch/device.h>
#include <asm/arch/msg_port.h>
#include <asm/arch/quark.h>
static struct pci_device_id mmc_supported[] = {
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_QRK_SDIO },
};
/*
* TODO:
*
* This whole routine should be removed until we fully convert the ICH SPI
* driver to DM and make use of DT to pass the bios control register offset
*/
static void unprotect_spi_flash(void)
{
u32 bc;
qrk_pci_read_config_dword(QUARK_LEGACY_BRIDGE, 0xd8, &bc);
bc |= 0x1; /* unprotect the flash */
qrk_pci_write_config_dword(QUARK_LEGACY_BRIDGE, 0xd8, bc);
}
static void quark_setup_bars(void)
{
/* GPIO - D31:F0:R44h */
qrk_pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_GBA,
CONFIG_GPIO_BASE | IO_BAR_EN);
/* ACPI PM1 Block - D31:F0:R48h */
qrk_pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_PM1BLK,
CONFIG_ACPI_PM1_BASE | IO_BAR_EN);
/* GPE0 - D31:F0:R4Ch */
qrk_pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_GPE0BLK,
CONFIG_ACPI_GPE0_BASE | IO_BAR_EN);
/* WDT - D31:F0:R84h */
qrk_pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_WDTBA,
CONFIG_WDT_BASE | IO_BAR_EN);
/* RCBA - D31:F0:RF0h */
qrk_pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_RCBA,
CONFIG_RCBA_BASE | MEM_BAR_EN);
/* ACPI P Block - Msg Port 04:R70h */
msg_port_write(MSG_PORT_RMU, PBLK_BA,
CONFIG_ACPI_PBLK_BASE | IO_BAR_EN);
/* SPI DMA - Msg Port 04:R7Ah */
msg_port_write(MSG_PORT_RMU, SPI_DMA_BA,
CONFIG_SPI_DMA_BASE | IO_BAR_EN);
/* PCIe ECAM */
msg_port_write(MSG_PORT_MEM_ARBITER, AEC_CTRL,
CONFIG_PCIE_ECAM_BASE | MEM_BAR_EN);
msg_port_write(MSG_PORT_HOST_BRIDGE, HEC_REG,
CONFIG_PCIE_ECAM_BASE | MEM_BAR_EN);
}
static void quark_pcie_early_init(void)
{
u32 pcie_cfg;
/*
* Step1: Assert PCIe signal PERST#
*
* The CPU interface to the PERST# signal is platform dependent.
* Call the board-specific codes to perform this task.
*/
board_assert_perst();
/* Step2: PHY common lane reset */
pcie_cfg = msg_port_alt_read(MSG_PORT_SOC_UNIT, PCIE_CFG);
pcie_cfg |= PCIE_PHY_LANE_RST;
msg_port_alt_write(MSG_PORT_SOC_UNIT, PCIE_CFG, pcie_cfg);
/* wait 1 ms for PHY common lane reset */
mdelay(1);
/* Step3: PHY sideband interface reset and controller main reset */
pcie_cfg = msg_port_alt_read(MSG_PORT_SOC_UNIT, PCIE_CFG);
pcie_cfg |= (PCIE_PHY_SB_RST | PCIE_CTLR_MAIN_RST);
msg_port_alt_write(MSG_PORT_SOC_UNIT, PCIE_CFG, pcie_cfg);
/* wait 80ms for PLL to lock */
mdelay(80);
/* Step4: Controller sideband interface reset */
pcie_cfg = msg_port_alt_read(MSG_PORT_SOC_UNIT, PCIE_CFG);
pcie_cfg |= PCIE_CTLR_SB_RST;
msg_port_alt_write(MSG_PORT_SOC_UNIT, PCIE_CFG, pcie_cfg);
/* wait 20ms for controller sideband interface reset */
mdelay(20);
/* Step5: De-assert PERST# */
board_deassert_perst();
/* Step6: Controller primary interface reset */
pcie_cfg = msg_port_alt_read(MSG_PORT_SOC_UNIT, PCIE_CFG);
pcie_cfg |= PCIE_CTLR_PRI_RST;
msg_port_alt_write(MSG_PORT_SOC_UNIT, PCIE_CFG, pcie_cfg);
/* Mixer Load Lane 0 */
pcie_cfg = msg_port_io_read(MSG_PORT_PCIE_AFE, PCIE_RXPICTRL0_L0);
pcie_cfg &= ~((1 << 6) | (1 << 7));
msg_port_io_write(MSG_PORT_PCIE_AFE, PCIE_RXPICTRL0_L0, pcie_cfg);
/* Mixer Load Lane 1 */
pcie_cfg = msg_port_io_read(MSG_PORT_PCIE_AFE, PCIE_RXPICTRL0_L1);
pcie_cfg &= ~((1 << 6) | (1 << 7));
msg_port_io_write(MSG_PORT_PCIE_AFE, PCIE_RXPICTRL0_L1, pcie_cfg);
}
static void quark_usb_early_init(void)
{
u32 usb;
/* The sequence below comes from Quark firmware writer guide */
usb = msg_port_alt_read(MSG_PORT_USB_AFE, USB2_GLOBAL_PORT);
usb &= ~(1 << 1);
usb |= ((1 << 6) | (1 << 7));
msg_port_alt_write(MSG_PORT_USB_AFE, USB2_GLOBAL_PORT, usb);
usb = msg_port_alt_read(MSG_PORT_USB_AFE, USB2_COMPBG);
usb &= ~((1 << 8) | (1 << 9));
usb |= ((1 << 7) | (1 << 10));
msg_port_alt_write(MSG_PORT_USB_AFE, USB2_COMPBG, usb);
usb = msg_port_alt_read(MSG_PORT_USB_AFE, USB2_PLL2);
usb |= (1 << 29);
msg_port_alt_write(MSG_PORT_USB_AFE, USB2_PLL2, usb);
usb = msg_port_alt_read(MSG_PORT_USB_AFE, USB2_PLL1);
usb |= (1 << 1);
msg_port_alt_write(MSG_PORT_USB_AFE, USB2_PLL1, usb);
usb = msg_port_alt_read(MSG_PORT_USB_AFE, USB2_PLL1);
usb &= ~((1 << 3) | (1 << 4) | (1 << 5));
usb |= (1 << 6);
msg_port_alt_write(MSG_PORT_USB_AFE, USB2_PLL1, usb);
usb = msg_port_alt_read(MSG_PORT_USB_AFE, USB2_PLL2);
usb &= ~(1 << 29);
msg_port_alt_write(MSG_PORT_USB_AFE, USB2_PLL2, usb);
usb = msg_port_alt_read(MSG_PORT_USB_AFE, USB2_PLL2);
usb |= (1 << 24);
msg_port_alt_write(MSG_PORT_USB_AFE, USB2_PLL2, usb);
}
static void quark_enable_legacy_seg(void)
{
u32 hmisc2;
hmisc2 = msg_port_read(MSG_PORT_HOST_BRIDGE, HMISC2);
hmisc2 |= (HMISC2_SEGE | HMISC2_SEGF | HMISC2_SEGAB);
msg_port_write(MSG_PORT_HOST_BRIDGE, HMISC2, hmisc2);
}
int arch_cpu_init(void)
{
int ret;
post_code(POST_CPU_INIT);
#ifdef CONFIG_SYS_X86_TSC_TIMER
timer_set_base(rdtsc());
#endif
ret = x86_cpu_init_f();
if (ret)
return ret;
/*
* Quark SoC has some non-standard BARs (excluding PCI standard BARs)
* which need be initialized with suggested values
*/
quark_setup_bars();
/*
* Initialize PCIe controller
*
* Quark SoC holds the PCIe controller in reset following a power on.
* U-Boot needs to release the PCIe controller from reset. The PCIe
* controller (D23:F0/F1) will not be visible in PCI configuration
* space and any access to its PCI configuration registers will cause
* system hang while it is held in reset.
*/
quark_pcie_early_init();
/* Initialize USB2 PHY */
quark_usb_early_init();
/* Turn on legacy segments (A/B/E/F) decode to system RAM */
quark_enable_legacy_seg();
unprotect_spi_flash();
return 0;
}
int print_cpuinfo(void)
{
post_code(POST_CPU_INFO);
return default_print_cpuinfo();
}
void reset_cpu(ulong addr)
{
/* cold reset */
x86_full_reset();
}
static void quark_pcie_init(void)
{
u32 val;
/* PCIe upstream non-posted & posted request size */
qrk_pci_write_config_dword(QUARK_PCIE0, PCIE_RP_CCFG,
CCFG_UPRS | CCFG_UNRS);
qrk_pci_write_config_dword(QUARK_PCIE1, PCIE_RP_CCFG,
CCFG_UPRS | CCFG_UNRS);
/* PCIe packet fast transmit mode (IPF) */
qrk_pci_write_config_dword(QUARK_PCIE0, PCIE_RP_MPC2, MPC2_IPF);
qrk_pci_write_config_dword(QUARK_PCIE1, PCIE_RP_MPC2, MPC2_IPF);
/* PCIe message bus idle counter (SBIC) */
qrk_pci_read_config_dword(QUARK_PCIE0, PCIE_RP_MBC, &val);
val |= MBC_SBIC;
qrk_pci_write_config_dword(QUARK_PCIE0, PCIE_RP_MBC, val);
qrk_pci_read_config_dword(QUARK_PCIE1, PCIE_RP_MBC, &val);
val |= MBC_SBIC;
qrk_pci_write_config_dword(QUARK_PCIE1, PCIE_RP_MBC, val);
}
static void quark_usb_init(void)
{
u32 bar;
/* Change USB EHCI packet buffer OUT/IN threshold */
qrk_pci_read_config_dword(QUARK_USB_EHCI, PCI_BASE_ADDRESS_0, &bar);
writel((0x7f << 16) | 0x7f, bar + EHCI_INSNREG01);
/* Disable USB device interrupts */
qrk_pci_read_config_dword(QUARK_USB_DEVICE, PCI_BASE_ADDRESS_0, &bar);
writel(0x7f, bar + USBD_INT_MASK);
writel((0xf << 16) | 0xf, bar + USBD_EP_INT_MASK);
writel((0xf << 16) | 0xf, bar + USBD_EP_INT_STS);
}
int arch_early_init_r(void)
{
quark_pcie_init();
quark_usb_init();
return 0;
}
int cpu_mmc_init(bd_t *bis)
{
return pci_mmc_init("Quark SDHCI", mmc_supported,
ARRAY_SIZE(mmc_supported));
}
void cpu_irq_init(void)
{
struct quark_rcba *rcba;
u32 base;
qrk_pci_read_config_dword(QUARK_LEGACY_BRIDGE, LB_RCBA, &base);
base &= ~MEM_BAR_EN;
rcba = (struct quark_rcba *)base;
/*
* Route Quark PCI device interrupt pin to PIRQ
*
* Route device#23's INTA/B/C/D to PIRQA/B/C/D
* Route device#20,21's INTA/B/C/D to PIRQE/F/G/H
*/
writew(PIRQC, &rcba->rmu_ir);
writew(PIRQA | (PIRQB << 4) | (PIRQC << 8) | (PIRQD << 12),
&rcba->d23_ir);
writew(PIRQD, &rcba->core_ir);
writew(PIRQE | (PIRQF << 4) | (PIRQG << 8) | (PIRQH << 12),
&rcba->d20d21_ir);
}
int arch_misc_init(void)
{
return pirq_init();
}
void board_final_cleanup(void)
{
struct quark_rcba *rcba;
u32 base, val;
qrk_pci_read_config_dword(QUARK_LEGACY_BRIDGE, LB_RCBA, &base);
base &= ~MEM_BAR_EN;
rcba = (struct quark_rcba *)base;
/* Initialize 'Component ID' to zero */
val = readl(&rcba->esd);
val &= ~0xff0000;
writel(val, &rcba->esd);
return;
}