u-boot-brain/include/configs/imx6_spl.h
Marek Vasut 291000894e ARM: mx6: Enable MMC and SATA extfs boot support
Enable support for booting U-Boot image from ext filesystem when either
SD/MMC or SATA support is compiled into the SPL. This will allow easy
transition from loading U-Boot image from ad-hoc offset on the card to
loading U-Boot image from the filesystem. VFAT support is intently not
enabled. The boot order is tweaked so that raw is tested first and if
the raw has no signature, FS boot is attempted.

To install just the SPL on i.MX6 board, perform the following operation
 $ dd if=SPL of=/dev/sdX seek=2 bs=512
To install the U-Boot image, copy u-boot.img to the first partition of
the SD/MMC/SATA drive. The partition must be formated to extfs.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
2016-05-17 17:52:20 +02:00

85 lines
2.8 KiB
C

/*
* Copyright (C) 2014 Gateworks Corporation
* Author: Tim Harvey <tharvey@gateworks.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __IMX6_SPL_CONFIG_H
#define __IMX6_SPL_CONFIG_H
#ifdef CONFIG_SPL
#define CONFIG_SPL_FRAMEWORK
/*
* see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
* - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
* - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well
* - BOOT ROM stack is at 0x0091FFB8
* - if icache/dcache is enabled (eFuse/strapping controlled) then the
* IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
* fit between 0x00907000 and 0x00918000.
* - Additionally the BOOT ROM loads what they consider the firmware image
* which consists of a 4K header in front of us that contains the IVT, DCD
* and some padding thus 'our' max size is really 0x00908000 - 0x00918000
* or 64KB
*/
#define CONFIG_SYS_THUMB_BUILD
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/omap-common/u-boot-spl.lds"
#define CONFIG_SPL_TEXT_BASE 0x00908000
#define CONFIG_SPL_MAX_SIZE 0x10000
#define CONFIG_SPL_STACK 0x0091FFB8
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_WATCHDOG_SUPPORT
/* NAND support */
#if defined(CONFIG_SPL_NAND_SUPPORT)
#define CONFIG_SPL_NAND_MXS
#define CONFIG_SPL_DMA_SUPPORT
#endif
/* MMC support */
#if defined(CONFIG_SPL_MMC_SUPPORT)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 138 /* offset 69KB */
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS/2*1024)
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#define CONFIG_SPL_EXT_SUPPORT
#endif
/* SATA support */
#if defined(CONFIG_SPL_SATA_SUPPORT)
#define CONFIG_SPL_SATA_BOOT_DEVICE 0
#define CONFIG_SYS_SATA_FAT_BOOT_PARTITION 1
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#define CONFIG_SPL_EXT_SUPPORT
#endif
/* Define the payload for FAT/EXT support */
#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_SPL_LIBDISK_SUPPORT
#endif
#if defined(CONFIG_MX6SX) || defined(CONFIG_MX6UL) || defined(CONFIG_MX6SL)
#define CONFIG_SPL_BSS_START_ADDR 0x88200000
#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
#define CONFIG_SYS_SPL_MALLOC_START 0x88300000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
#define CONFIG_SYS_TEXT_BASE 0x87800000
#else
#define CONFIG_SPL_BSS_START_ADDR 0x18200000
#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
#define CONFIG_SYS_SPL_MALLOC_START 0x18300000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
#define CONFIG_SYS_TEXT_BASE 0x17800000
#endif
#endif
#endif