brain-hackers_pepepper-mirror/u-boot-brain
1
0
Fork 0
mirror of https://github.com/brain-hackers/u-boot-brain synced 2024-07-06 03:06:16 +09:00
Code Issues Projects Releases Wiki Activity
2464b229b5
u-boot-brain/board/freescale/mx6memcal/spl.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style 
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

456 lines
14 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2016 Nelson Integration, LLC
* Author: Eric Nelson <eric@nelint.com>
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/iomux.h>
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <spl.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
static iomux_v3_cfg_t const uart_pads[] = {
#ifdef CONFIG_UART2_EIM_D26_27
IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
#elif defined(CONFIG_UART1_CSI0_DAT10_11)
IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
#elif defined(CONFIG_UART1_SD3_DAT6_7)
IOMUX_PADS(PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
#elif defined(CONFIG_UART1_UART1)
MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
#else
#error select UART console pads
#endif
};
#ifdef CONFIG_DDR3
#define GRP_DDRTYPE 0x000C0000
#else
#define GRP_DDRTYPE 0x00080000
#endif
/* all existing designs have this disabled */
#define DDR_PKE 0
/* use Kconfig for ODT and DRIVE_STRENGTH */
#define DDR_ODT \
(CONFIG_DDR_ODT << 8)
#define DRAM_DRIVE_STRENGTH \
(CONFIG_DRAM_DRIVE_STRENGTH << 3)
/* configure MX6Q/DUAL mmdc DDR io registers */
static struct mx6dq_iomux_ddr_regs const mx6dq_ddr_ioregs = {
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
.dram_sdclk_0 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_sdclk_1 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_cas = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_ras = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_reset = DDR_ODT + DRAM_DRIVE_STRENGTH,
/* SDCKE[0:1]: 100k pull-up */
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
/* SDBA2: pull-up disabled */
.dram_sdba2 = 0x00000000,
/* SDODT[0:1]: 100k pull-up, 40 ohm */
.dram_sdodt0 = 0x00003000 + DRAM_DRIVE_STRENGTH,
.dram_sdodt1 = 0x00003000 + DRAM_DRIVE_STRENGTH,
/* SDQS[0:7]: Differential input, 40 ohm */
.dram_sdqs0 = DRAM_DRIVE_STRENGTH,
.dram_sdqs1 = DRAM_DRIVE_STRENGTH,
.dram_sdqs2 = DRAM_DRIVE_STRENGTH,
.dram_sdqs3 = DRAM_DRIVE_STRENGTH,
.dram_sdqs4 = DRAM_DRIVE_STRENGTH,
.dram_sdqs5 = DRAM_DRIVE_STRENGTH,
.dram_sdqs6 = DRAM_DRIVE_STRENGTH,
.dram_sdqs7 = DRAM_DRIVE_STRENGTH,
/* DQM[0:7]: Differential input, 40 ohm */
.dram_dqm0 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm1 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm2 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm3 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm4 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm5 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm6 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm7 = DDR_ODT + DRAM_DRIVE_STRENGTH,
};
/* configure MX6Q/DUAL mmdc GRP io registers */
static struct mx6dq_iomux_grp_regs const mx6dq_grp_ioregs = {
/* DDR3 */
.grp_ddr_type = GRP_DDRTYPE,
.grp_ddrmode_ctl = DDR_ODT,
/* disable DDR pullups */
.grp_ddrpke = DDR_PKE,
/* ADDR[00:16], SDBA[0:1]: 40 ohm */
.grp_addds = DRAM_DRIVE_STRENGTH,
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
.grp_ctlds = DRAM_DRIVE_STRENGTH,
/* DATA[00:63]: Differential input, 40 ohm */
.grp_ddrmode = DDR_ODT,
.grp_b0ds = DRAM_DRIVE_STRENGTH,
.grp_b1ds = DRAM_DRIVE_STRENGTH,
.grp_b2ds = DRAM_DRIVE_STRENGTH,
.grp_b3ds = DRAM_DRIVE_STRENGTH,
.grp_b4ds = DRAM_DRIVE_STRENGTH,
.grp_b5ds = DRAM_DRIVE_STRENGTH,
.grp_b6ds = DRAM_DRIVE_STRENGTH,
.grp_b7ds = DRAM_DRIVE_STRENGTH,
};
static struct mx6sdl_iomux_ddr_regs const mx6sdl_ddr_ioregs = {
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
.dram_sdclk_0 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_sdclk_1 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_cas = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_ras = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_reset = DDR_ODT + DRAM_DRIVE_STRENGTH,
/* SDCKE[0:1]: 100k pull-up */
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
/* SDBA2: pull-up disabled */
.dram_sdba2 = 0x00000000,
/* SDODT[0:1]: 100k pull-up, 40 ohm */
.dram_sdodt0 = 0x00003000 + DRAM_DRIVE_STRENGTH,
.dram_sdodt1 = 0x00003000 + DRAM_DRIVE_STRENGTH,
/* SDQS[0:7]: Differential input, 40 ohm */
.dram_sdqs0 = DRAM_DRIVE_STRENGTH,
.dram_sdqs1 = DRAM_DRIVE_STRENGTH,
.dram_sdqs2 = DRAM_DRIVE_STRENGTH,
.dram_sdqs3 = DRAM_DRIVE_STRENGTH,
.dram_sdqs4 = DRAM_DRIVE_STRENGTH,
.dram_sdqs5 = DRAM_DRIVE_STRENGTH,
.dram_sdqs6 = DRAM_DRIVE_STRENGTH,
.dram_sdqs7 = DRAM_DRIVE_STRENGTH,
/* DQM[0:7]: Differential input, 40 ohm */
.dram_dqm0 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm1 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm2 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm3 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm4 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm5 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm6 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm7 = DDR_ODT + DRAM_DRIVE_STRENGTH,
};
/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
static struct mx6sdl_iomux_grp_regs const mx6sdl_grp_ioregs = {
/* DDR3 */
.grp_ddr_type = GRP_DDRTYPE,
/* SDQS[0:7]: Differential input, 40 ohm */
.grp_ddrmode_ctl = DDR_ODT,
/* disable DDR pullups */
.grp_ddrpke = DDR_PKE,
/* ADDR[00:16], SDBA[0:1]: 40 ohm */
.grp_addds = DRAM_DRIVE_STRENGTH,
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
.grp_ctlds = DRAM_DRIVE_STRENGTH,
/* DATA[00:63]: Differential input, 40 ohm */
.grp_ddrmode = DDR_ODT,
.grp_b0ds = DRAM_DRIVE_STRENGTH,
.grp_b1ds = DRAM_DRIVE_STRENGTH,
.grp_b2ds = DRAM_DRIVE_STRENGTH,
.grp_b3ds = DRAM_DRIVE_STRENGTH,
.grp_b4ds = DRAM_DRIVE_STRENGTH,
.grp_b5ds = DRAM_DRIVE_STRENGTH,
.grp_b6ds = DRAM_DRIVE_STRENGTH,
.grp_b7ds = DRAM_DRIVE_STRENGTH,
};
const struct mx6sl_iomux_ddr_regs mx6sl_ddr_ioregs = {
.dram_sdqs0 = DRAM_DRIVE_STRENGTH,
.dram_sdqs1 = DRAM_DRIVE_STRENGTH,
.dram_sdqs2 = DRAM_DRIVE_STRENGTH,
.dram_sdqs3 = DRAM_DRIVE_STRENGTH,
.dram_dqm0 = DRAM_DRIVE_STRENGTH,
.dram_dqm1 = DRAM_DRIVE_STRENGTH,
.dram_dqm2 = DRAM_DRIVE_STRENGTH,
.dram_dqm3 = DRAM_DRIVE_STRENGTH,
.dram_cas = DRAM_DRIVE_STRENGTH,
.dram_ras = DRAM_DRIVE_STRENGTH,
.dram_sdclk_0 = DRAM_DRIVE_STRENGTH,
.dram_reset = DRAM_DRIVE_STRENGTH,
.dram_sdba2 = 0x00020000,
.dram_odt0 = 0x00030000 + DRAM_DRIVE_STRENGTH,
.dram_odt1 = 0x00030000 + DRAM_DRIVE_STRENGTH,
};
const struct mx6sl_iomux_grp_regs mx6sl_grp_ioregs = {
.grp_b0ds = DRAM_DRIVE_STRENGTH,
.grp_b1ds = DRAM_DRIVE_STRENGTH,
.grp_b2ds = DRAM_DRIVE_STRENGTH,
.grp_b3ds = DRAM_DRIVE_STRENGTH,
.grp_addds = DRAM_DRIVE_STRENGTH,
.grp_ctlds = DRAM_DRIVE_STRENGTH,
.grp_ddrmode_ctl = DDR_ODT,
.grp_ddrpke = DDR_PKE,
.grp_ddrmode = DDR_ODT,
.grp_ddr_type = GRP_DDRTYPE,
};
static struct mx6_ddr_sysinfo const sysinfo = {
/* width of data bus:0=16,1=32,2=64 */
#if CONFIG_DDRWIDTH == 32
.dsize = 1,
#elif CONFIG_DDRWIDTH == 64
.dsize = 2,
#else
#error missing CONFIG_DDRWIDTH
#endif
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 32Gb per CS */
/* # of chip selects */
.ncs = CONFIG_DDRCS,
.cs1_mirror = 0,
.bi_on = 1, /* Bank interleaving enabled */
.rtt_nom = CONFIG_RTT_NOM,
.rtt_wr = CONFIG_RTT_WR,
.ralat = CONFIG_RALAT, /* Read additional latency */
.walat = CONFIG_WALAT, /* Write additional latency */
.mif3_mode = 3, /* Command prediction working mode */
#ifdef CONFIG_DDR3
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.sde_to_rst = 0x10, /* JEDEC value for LPDDR2 - 200us */
.pd_fast_exit = 0, /* immaterial for calibration */
.ddr_type = DDR_TYPE_DDR3,
#else
.rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */
.sde_to_rst = 0, /* LPDDR2 does not need this field */
.pd_fast_exit = 0, /* immaterial for calibration */
.ddr_type = DDR_TYPE_LPDDR2,
#endif
.refsel = CONFIG_REFSEL,
.refr = CONFIG_REFR,
};
#ifdef CONFIG_MT41K512M16TNA
/* Micron MT41K512M16TNA-125 */
static struct mx6_ddr3_cfg const ddrtype = {
.mem_speed = 1600,
.density = 8,
.width = 16,
.banks = 8,
.rowaddr = 15,
.coladdr = 10,
.pagesz = 1,
.trcd = 1375,
.trcmin = 5062,
.trasmin = 3750,
};
#elif defined(CONFIG_MT41K128M16JT)
/* Micron MT41K128M16JT-125 */
static struct mx6_ddr3_cfg const ddrtype = {
.mem_speed = 1600,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
#elif defined(CONFIG_H5TQ4G63AFR)
/* Hynix H5TQ4G63AFR */
static struct mx6_ddr3_cfg const ddrtype = {
.mem_speed = 1600,
.density = 4,
.width = 16,
.banks = 8,
.rowaddr = 15,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
#elif defined CONFIG_H5TQ2G63DFR
/* Hynix H5TQ2G63DFR */
static struct mx6_ddr3_cfg const ddrtype = {
.mem_speed = 1333,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1350,
.trcmin = 4950,
.trasmin = 3600,
};
#elif defined(CONFIG_MT42L256M32D2LG)
/* Micron MT42L256M32D2LG */
static struct mx6_lpddr2_cfg ddrtype = {
.mem_speed = 800,
.density = 4,
.width = 32,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.trcd_lp = 2000,
.trppb_lp = 2000,
.trpab_lp = 2250,
.trasmin = 4200,
};
#elif defined(CONFIG_MT29PZZZ4D4BKESK)
/* Micron MT29PZZZ4D4BKESK */
static struct mx6_lpddr2_cfg ddrtype = {
.mem_speed = 800,
.density = 4,
.width = 32,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.trcd_lp = 2000,
.trppb_lp = 2000,
.trpab_lp = 2250,
.trasmin = 4200,
};
#else
#error please select DDR type using menuconfig
#endif
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/* FIXME: these should probably be checked, especially
* for i.MX6SL, UL, ULL
*/
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x0030FC03, &ccm->CCGR1);
writel(0x0FFFC000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0x00FFF300, &ccm->CCGR4);
writel(0x0F0000C3, &ccm->CCGR5);
writel(0x000003FF, &ccm->CCGR6);
}
static void display_calibration(struct mx6_mmdc_calibration *calib)
{
printf(".p0_mpdgctrl0\t= 0x%08X\n", calib->p0_mpdgctrl0);
printf(".p0_mpdgctrl1\t= 0x%08X\n", calib->p0_mpdgctrl1);
printf(".p0_mprddlctl\t= 0x%08X\n", calib->p0_mprddlctl);
printf(".p0_mpwrdlctl\t= 0x%08X\n", calib->p0_mpwrdlctl);
printf(".p0_mpwldectrl0\t= 0x%08X\n", calib->p0_mpwldectrl0);
printf(".p0_mpwldectrl1\t= 0x%08X\n", calib->p0_mpwldectrl1);
if (sysinfo.dsize == 2) {
printf(".p1_mpdgctrl0\t= 0x%08X\n", calib->p1_mpdgctrl0);
printf(".p1_mpdgctrl1\t= 0x%08X\n", calib->p1_mpdgctrl1);
printf(".p1_mprddlctl\t= 0x%08X\n", calib->p1_mprddlctl);
printf(".p1_mpwrdlctl\t= 0x%08X\n", calib->p1_mpwrdlctl);
printf(".p1_mpwldectrl0\t= 0x%08X\n", calib->p1_mpwldectrl0);
printf(".p1_mpwldectrl1\t= 0x%08X\n", calib->p1_mpwldectrl1);
}
#ifdef CONFIG_IMXIMAGE_OUTPUT
printf("DATA 4 MX6_MMDC_P0_MPDGCTRL0\t= 0x%08X\n", calib->p0_mpdgctrl0);
printf("DATA 4 MX6_MMDC_P0_MPDGCTRL1\t= 0x%08X\n", calib->p0_mpdgctrl1);
printf("DATA 4 MX6_MMDC_P0_MPRDDLCTL\t= 0x%08X\n", calib->p0_mprddlctl);
printf("DATA 4 MX6_MMDC_P0_MPWRDLCTL\t= 0x%08X\n", calib->p0_mpwrdlctl);
printf("DATA 4 MX6_MMDC_P0_MPWLDECTRL0\t= 0x%08X\n",
calib->p0_mpwldectrl0);
printf("DATA 4 MX6_MMDC_P0_MPWLDECTRL1\t= 0x%08X\n",
calib->p0_mpwldectrl1);
if (sysinfo.dsize == 2) {
printf("DATA 4 MX6_MMDC_P1_MPDGCTRL0\t= 0x%08X\n",
calib->p1_mpdgctrl0);
printf("DATA 4 MX6_MMDC_P1_MPDGCTRL1\t= 0x%08X\n",
calib->p1_mpdgctrl1);
printf("DATA 4 MX6_MMDC_P1_MPRDDLCTL\t= 0x%08X\n",
calib->p1_mprddlctl);
printf("DATA 4 MX6_MMDC_P1_MPWRDLCTL\t= 0x%08X\n",
calib->p1_mpwrdlctl);
printf("DATA 4 MX6_MMDC_P1_MPWLDECTRL0\t= 0x%08X\n",
calib->p1_mpwldectrl0);
printf("DATA 4 MX6_MMDC_P1_MPWLDECTRL1\t= 0x%08X\n",
calib->p1_mpwldectrl1);
}
#endif
}
/*
* called from C runtime startup code (arch/arm/lib/crt0.S:_main)
* - we have a stack and a place to store GD, both in SRAM
* - no variable global data is available
*/
void board_init_f(ulong dummy)
{
int errs;
struct mx6_mmdc_calibration calibration = {0};
memset((void *)gd, 0, sizeof(struct global_data));
/* write leveling calibration defaults */
calibration.p0_mpwrdlctl = 0x40404040;
calibration.p1_mpwrdlctl = 0x40404040;
/* setup AIPS and disable watchdog */
arch_cpu_init();
ccgr_init();
SETUP_IOMUX_PADS(uart_pads);
/* setup GP timer */
timer_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
if (sysinfo.dsize != 1) {
if (is_cpu_type(MXC_CPU_MX6SX) ||
is_cpu_type(MXC_CPU_MX6UL) ||
is_cpu_type(MXC_CPU_MX6ULL) ||
is_cpu_type(MXC_CPU_MX6SL)) {
printf("cpu type 0x%x doesn't support 64-bit bus\n",
get_cpu_type());
reset_cpu(0);
}
}
#ifdef CONFIG_MX6SL
mx6sl_dram_iocfg(CONFIG_DDRWIDTH, &mx6sl_ddr_ioregs,
&mx6sl_grp_ioregs);
#else
if (is_cpu_type(MXC_CPU_MX6Q)) {
mx6dq_dram_iocfg(CONFIG_DDRWIDTH, &mx6dq_ddr_ioregs,
&mx6dq_grp_ioregs);
} else {
mx6sdl_dram_iocfg(CONFIG_DDRWIDTH, &mx6sdl_ddr_ioregs,
&mx6sdl_grp_ioregs);
}
#endif
mx6_dram_cfg(&sysinfo, &calibration, &ddrtype);
errs = mmdc_do_write_level_calibration(&sysinfo);
if (errs) {
printf("error %d from write level calibration\n", errs);
} else {
errs = mmdc_do_dqs_calibration(&sysinfo);
if (errs) {
printf("error %d from dqs calibration\n", errs);
} else {
printf("completed successfully\n");
mmdc_read_calibration(&sysinfo, &calibration);
display_calibration(&calibration);
}
}
}
Reference in New Issue View Git Blame Copy Permalink