mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-09-03 03:13:21 +09:00
![Heiko Schocher](/assets/img/avatar_default.png)
add DM/DTS support for the UEC ethernet on QUICC Engine Block. Signed-off-by: Heiko Schocher <hs@denx.de> Patch-cc: Mario Six <mario.six@gdsys.cc> Patch-cc: Qiang Zhao <qiang.zhao@nxp.com> Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com> Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com> Series-changes: 3 - revert: commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled") as now qe works with DM and DM_ETH support. - fix mailaddress from Holger Series-changes: 2 - add comments from Qiang Zhao: - add device node documentation - I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c because using drivers/net/fsl_mdio.c leads in none existent udevice mdio@3320 instead boards with DM ETH support should use now this driver. - remove RFC tag Commit-notes: - I let the old none DM based implementation in code so boards should work with old implementation. This Code should be removed if all boards are converted to DM/DTS. - add the DM based qe uec driver under drivers/net/qe - Therefore copied the files uccf.c uccf.h uec.h from drivers/qe. So there are a lot of Codingstyle problems currently. I fix them in next version if this RFC patch is OK or it needs some changes. - The dm based driver code is now under drivers/net/qe/dm_qe_uec.c Used a lot of functions from drivers/qe/uec.c - seperated the PHY specific code into seperate file drivers/net/qe/dm_qe_uec_phy.c END
54 lines
2.3 KiB
Plaintext
54 lines
2.3 KiB
Plaintext
* UCC (Unified Communications Controllers)
|
|
|
|
Required properties:
|
|
- compatible : ucc_geth
|
|
- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
|
|
- reg : Offset and length of the register set for the device
|
|
- rx-clock-name: the UCC receive clock source
|
|
"none": clock source is disabled
|
|
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
|
|
"clk1" through "clk24": clock source is CLK1-CLK24, respectively
|
|
- tx-clock-name: the UCC transmit clock source
|
|
"none": clock source is disabled
|
|
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
|
|
"clk1" through "clk24": clock source is CLK1-CLK24, respectively
|
|
The following two properties are deprecated. rx-clock has been replaced
|
|
with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
|
|
Drivers that currently use the deprecated properties should continue to
|
|
do so, in order to support older device trees, but they should be updated
|
|
to check for the new properties first.
|
|
- rx-clock : represents the UCC receive clock source.
|
|
0x00 : clock source is disabled;
|
|
0x1~0x10 : clock source is BRG1~BRG16 respectively;
|
|
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
|
|
- tx-clock: represents the UCC transmit clock source;
|
|
0x00 : clock source is disabled;
|
|
0x1~0x10 : clock source is BRG1~BRG16 respectively;
|
|
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
|
|
- phy-handle : The phandle for the PHY connected to this controller.
|
|
- phy-connection-type : a string naming the controller/PHY interface type,
|
|
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
|
|
Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
|
|
"tbi", or "rtbi".
|
|
- pio-handle : The phandle for the Parallel I/O port configuration.
|
|
|
|
Deprecated properties:
|
|
- device-id : the ucc number(1-8), corresponding to UCCx in UM.
|
|
you should use cell-index
|
|
|
|
Example:
|
|
ucc@2000 {
|
|
device_type = "network";
|
|
compatible = "ucc_geth";
|
|
cell-index = <1>;
|
|
reg = <2000 200>;
|
|
interrupts = <a0 0>;
|
|
interrupt-parent = <700>;
|
|
mac-address = [ 00 04 9f 00 23 23 ];
|
|
rx-clock = "none";
|
|
tx-clock = "clk9";
|
|
phy-handle = <212000>;
|
|
phy-connection-type = "gmii";
|
|
pio-handle = <140001>;
|
|
};
|