mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-06-09 23:36:03 +09:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
482 lines
15 KiB
C
482 lines
15 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Based on corenet_ds.h
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#if !defined(CONFIG_ARCH_P5020) && !defined(CONFIG_ARCH_P5040)
|
|
#error Must call Cyrus CONFIG with a specific CPU enabled.
|
|
#endif
|
|
|
|
#define CONFIG_SDCARD
|
|
#define CONFIG_FSL_SATA_V2
|
|
#define CONFIG_PCIE3
|
|
#define CONFIG_PCIE4
|
|
#ifdef CONFIG_ARCH_P5020
|
|
#define CONFIG_SYS_FSL_RAID_ENGINE
|
|
#define CONFIG_SYS_DPAA_RMAN
|
|
#endif
|
|
#define CONFIG_SYS_DPAA_PME
|
|
|
|
/*
|
|
* Corenet DS style board configuration file
|
|
*/
|
|
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
|
|
#define CONFIG_SYS_FSL_PBL_PBI board/varisys/cyrus/pbi.cfg
|
|
#if defined(CONFIG_ARCH_P5020)
|
|
#define CONFIG_SYS_CLK_FREQ 133000000
|
|
#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5020_v2.cfg
|
|
#elif defined(CONFIG_ARCH_P5040)
|
|
#define CONFIG_SYS_CLK_FREQ 100000000
|
|
#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5040.cfg
|
|
#endif
|
|
|
|
/* High Level Configuration Options */
|
|
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
|
|
#define CONFIG_MP /* support multiple processors */
|
|
|
|
#define CONFIG_SYS_MMC_MAX_DEVICE 1
|
|
|
|
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
|
|
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
|
|
#define CONFIG_PCIE1 /* PCIE controller 1 */
|
|
#define CONFIG_PCIE2 /* PCIE controller 2 */
|
|
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
|
|
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
|
|
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#if defined(CONFIG_SDCARD)
|
|
#define CONFIG_SYS_EXTRA_ENV_RELOC
|
|
#define CONFIG_FSL_FIXED_MMC_LOCATION
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#define CONFIG_ENV_OFFSET (512 * 1658)
|
|
#endif
|
|
|
|
/*
|
|
* These can be toggled for performance analysis, otherwise use default.
|
|
*/
|
|
#define CONFIG_SYS_CACHE_STASHING
|
|
#define CONFIG_BACKSIDE_L2_CACHE
|
|
#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
|
|
#define CONFIG_BTB /* toggle branch predition */
|
|
#define CONFIG_DDR_ECC
|
|
#ifdef CONFIG_DDR_ECC
|
|
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
|
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
|
#endif
|
|
|
|
#define CONFIG_ENABLE_36BIT_PHYS
|
|
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_ADDR_MAP
|
|
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
|
|
#endif
|
|
|
|
/* test POST memory test */
|
|
#undef CONFIG_POST
|
|
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x00400000
|
|
|
|
/*
|
|
* Config the L3 Cache as L3 SRAM
|
|
*/
|
|
#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE)
|
|
#else
|
|
#define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR
|
|
#endif
|
|
#define CONFIG_SYS_L3_SIZE (1024 << 10)
|
|
#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
|
|
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_DCSRBAR 0xf0000000
|
|
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
|
|
#endif
|
|
|
|
/*
|
|
* DDR Setup
|
|
*/
|
|
#define CONFIG_VERY_BIG_RAM
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
|
|
|
|
#define CONFIG_DDR_SPD
|
|
|
|
#define CONFIG_SYS_SPD_BUS_NUM 1
|
|
#define SPD_EEPROM_ADDRESS1 0x51
|
|
#define SPD_EEPROM_ADDRESS2 0x52
|
|
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
|
|
|
|
/*
|
|
* Local Bus Definitions
|
|
*/
|
|
|
|
#define CONFIG_SYS_LBC0_BASE 0xe0000000 /* Start of LBC Registers */
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_LBC0_BASE_PHYS 0xfe0000000ull
|
|
#else
|
|
#define CONFIG_SYS_LBC0_BASE_PHYS CONFIG_SYS_LBC0_BASE
|
|
#endif
|
|
|
|
#define CONFIG_SYS_LBC1_BASE 0xe1000000 /* Start of LBC Registers */
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_LBC1_BASE_PHYS 0xfe1000000ull
|
|
#else
|
|
#define CONFIG_SYS_LBC1_BASE_PHYS CONFIG_SYS_LBC1_BASE
|
|
#endif
|
|
|
|
/* Set the local bus clock 1/16 of platform clock */
|
|
#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_16 | LCRR_EADC_1)
|
|
|
|
#define CONFIG_SYS_BR0_PRELIM \
|
|
(BR_PHYS_ADDR(CONFIG_SYS_LBC0_BASE_PHYS) | BR_PS_16 | BR_V)
|
|
#define CONFIG_SYS_BR1_PRELIM \
|
|
(BR_PHYS_ADDR(CONFIG_SYS_LBC1_BASE_PHYS) | BR_PS_16 | BR_V)
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM 0xfff00010
|
|
#define CONFIG_SYS_OR1_PRELIM 0xfff00010
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
|
|
#if defined(CONFIG_RAMBOOT_PBL)
|
|
#define CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
#define CONFIG_HWCONFIG
|
|
|
|
/* define to use L1 as initial stack */
|
|
#define CONFIG_L1_INIT_RAM
|
|
#define CONFIG_SYS_INIT_RAM_LOCK
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
|
|
/* The assembler doesn't like typecast */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
|
|
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
|
|
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
|
|
#else
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
|
|
#endif
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
|
|
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
|
|
|
|
/* Serial Port - controlled on board with jumper J8
|
|
* open - index 2
|
|
* shorted - index 1
|
|
*/
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
|
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
|
|
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
|
|
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_FSL
|
|
#define CONFIG_I2C_MULTI_BUS
|
|
#define CONFIG_I2C_CMD_TREE
|
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
|
|
#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
|
|
#define CONFIG_SYS_FSL_I2C3_SPEED 400000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
|
|
#define CONFIG_SYS_FSL_I2C4_SPEED 400000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
|
|
|
|
#define CONFIG_ID_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_NXID
|
|
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
|
|
|
|
#define CONFIG_SYS_I2C_GENERIC_MAC
|
|
#define CONFIG_SYS_I2C_MAC1_BUS 3
|
|
#define CONFIG_SYS_I2C_MAC1_CHIP_ADDR 0x57
|
|
#define CONFIG_SYS_I2C_MAC1_DATA_ADDR 0xf2
|
|
#define CONFIG_SYS_I2C_MAC2_BUS 0
|
|
#define CONFIG_SYS_I2C_MAC2_CHIP_ADDR 0x50
|
|
#define CONFIG_SYS_I2C_MAC2_DATA_ADDR 0xfa
|
|
|
|
#define CONFIG_RTC_MCP79411 1
|
|
#define CONFIG_SYS_RTC_BUS_NUM 3
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x6f
|
|
|
|
/*
|
|
* eSPI - Enhanced SPI
|
|
*/
|
|
|
|
/*
|
|
* General PCI
|
|
* Memory space is mapped 1-1, but I/O space must start from 0.
|
|
*/
|
|
|
|
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
|
|
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
|
|
#else
|
|
#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
|
|
#endif
|
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
|
|
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
|
|
#else
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
|
|
#endif
|
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
|
|
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
|
|
#else
|
|
#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
|
|
#endif
|
|
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
|
|
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
|
|
#else
|
|
#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
|
|
#endif
|
|
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
|
|
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
|
|
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
|
|
#else
|
|
#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000
|
|
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000
|
|
#endif
|
|
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
|
|
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
|
|
#else
|
|
#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
|
|
#endif
|
|
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
/* controller 4, Base address 203000 */
|
|
#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
|
|
#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull
|
|
#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
|
|
#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
/* Qman/Bman */
|
|
#define CONFIG_SYS_BMAN_NUM_PORTALS 10
|
|
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
|
|
#else
|
|
#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
|
|
#endif
|
|
#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
|
|
#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
|
|
#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
|
|
#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
|
|
#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
|
|
#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
|
|
CONFIG_SYS_BMAN_CENA_SIZE)
|
|
#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
|
|
#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
|
|
#define CONFIG_SYS_QMAN_NUM_PORTALS 10
|
|
#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
|
|
#else
|
|
#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
|
|
#endif
|
|
#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
|
|
#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
|
|
#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
|
|
#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
|
|
#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
|
|
#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
|
|
CONFIG_SYS_QMAN_CENA_SIZE)
|
|
#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
|
|
#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
|
|
|
|
#define CONFIG_SYS_DPAA_FMAN
|
|
/* Default address of microcode for the Linux Fman driver */
|
|
/*
|
|
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
|
|
* about 825KB (1650 blocks), Env is stored after the image, and the env size is
|
|
* 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
|
|
*/
|
|
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
|
|
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
|
|
|
|
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
|
|
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
|
|
|
|
#ifdef CONFIG_SYS_DPAA_FMAN
|
|
#define CONFIG_FMAN_ENET
|
|
#endif
|
|
|
|
#ifdef CONFIG_PCI
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE
|
|
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#endif /* CONFIG_PCI */
|
|
|
|
/* SATA */
|
|
#ifdef CONFIG_FSL_SATA_V2
|
|
#define CONFIG_SYS_SATA_MAX_DEVICE 2
|
|
#define CONFIG_SATA1
|
|
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
|
|
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
|
|
#define CONFIG_SATA2
|
|
#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
|
|
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
|
|
|
|
#define CONFIG_LBA48
|
|
#endif
|
|
|
|
#ifdef CONFIG_FMAN_ENET
|
|
#define CONFIG_SYS_TBIPA_VALUE 8
|
|
#define CONFIG_MII /* MII PHY management */
|
|
#define CONFIG_ETHPRIME "FM1@DTSEC4"
|
|
#endif
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#define CONFIG_LOADS_ECHO /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
|
|
|
|
/*
|
|
* USB
|
|
*/
|
|
#define CONFIG_HAS_FSL_DR_USB
|
|
#define CONFIG_HAS_FSL_MPH_USB
|
|
|
|
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
|
|
#define CONFIG_USB_EHCI_FSL
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
#define CONFIG_EHCI_IS_TDI
|
|
/* _VIA_CONTROL_EP */
|
|
#endif
|
|
|
|
#ifdef CONFIG_MMC
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
|
|
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
|
|
#endif
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 64 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
|
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
|
|
|
#ifdef CONFIG_CMD_KGDB
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#endif
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ROOTPATH "/opt/nfsroot"
|
|
#define CONFIG_BOOTFILE "uImage"
|
|
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
|
|
|
|
/* default location for tftp and bootm */
|
|
#define CONFIG_LOADADDR 1000000
|
|
|
|
#define __USB_PHY_TYPE utmi
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
|
|
"bank_intlv=cs0_cs1;" \
|
|
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
|
|
"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
|
|
"netdev=eth0\0" \
|
|
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
|
|
"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
|
|
"consoledev=ttyS0\0" \
|
|
"ramdiskaddr=2000000\0" \
|
|
"fdtaddr=1e00000\0" \
|
|
"bdev=sda3\0"
|
|
|
|
#define CONFIG_HDBOOT \
|
|
"setenv bootargs root=/dev/$bdev rw " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=$serverip:$rootpath " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/ram rw " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $ramdiskaddr $ramdiskfile;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
|
|
#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
|
|
|
|
#include <asm/fsl_secure_boot.h>
|
|
|
|
#ifdef CONFIG_SECURE_BOOT
|
|
#endif
|
|
|
|
#endif /* __CONFIG_H */
|