mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-19 08:28:51 +09:00
![Tom Rini](/assets/img/avatar_default.png)
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
591 lines
12 KiB
C
591 lines
12 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2017 NXP
|
|
*/
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <malloc.h>
|
|
#include <errno.h>
|
|
#include <netdev.h>
|
|
#include <fsl_ifc.h>
|
|
#include <fsl_ddr.h>
|
|
#include <fsl_sec.h>
|
|
#include <asm/io.h>
|
|
#include <fdt_support.h>
|
|
#include <linux/libfdt.h>
|
|
#include <fsl-mc/fsl_mc.h>
|
|
#include <environment.h>
|
|
#include <asm/arch-fsl-layerscape/soc.h>
|
|
#include <asm/arch/ppa.h>
|
|
#include <hwconfig.h>
|
|
#include <asm/arch/fsl_serdes.h>
|
|
#include <asm/arch/soc.h>
|
|
|
|
#include "../common/qixis.h"
|
|
#include "ls1088a_qixis.h"
|
|
#include "../common/vid.h"
|
|
#include <fsl_immap.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
#if defined(CONFIG_SYS_I2C_EARLY_INIT) && defined(CONFIG_TARGET_LS1088AQDS)
|
|
i2c_early_init_f();
|
|
#endif
|
|
fsl_lsch3_early_init_f();
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_FSL_QIXIS
|
|
unsigned long long get_qixis_addr(void)
|
|
{
|
|
unsigned long long addr;
|
|
|
|
if (gd->flags & GD_FLG_RELOC)
|
|
addr = QIXIS_BASE_PHYS;
|
|
else
|
|
addr = QIXIS_BASE_PHYS_EARLY;
|
|
|
|
/*
|
|
* IFC address under 256MB is mapped to 0x30000000, any address above
|
|
* is mapped to 0x5_10000000 up to 4GB.
|
|
*/
|
|
addr = addr > 0x10000000 ? addr + 0x500000000ULL : addr + 0x30000000;
|
|
|
|
return addr;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_VID)
|
|
int init_func_vid(void)
|
|
{
|
|
if (adjust_vdd(0) < 0)
|
|
printf("core voltage not adjusted\n");
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#if !defined(CONFIG_SPL_BUILD)
|
|
int checkboard(void)
|
|
{
|
|
char buf[64];
|
|
u8 sw;
|
|
static const char *const freq[] = {"100", "125", "156.25",
|
|
"100 separate SSCG"};
|
|
int clock;
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
printf("Board: LS1088A-QDS, ");
|
|
#else
|
|
printf("Board: LS1088A-RDB, ");
|
|
#endif
|
|
|
|
sw = QIXIS_READ(arch);
|
|
printf("Board Arch: V%d, ", sw >> 4);
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
printf("Board version: %c, boot from ", (sw & 0xf) + 'A' - 1);
|
|
#else
|
|
printf("Board version: %c, boot from ", (sw & 0xf) + 'A');
|
|
#endif
|
|
|
|
memset((u8 *)buf, 0x00, ARRAY_SIZE(buf));
|
|
|
|
sw = QIXIS_READ(brdcfg[0]);
|
|
sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
|
|
|
|
#ifdef CONFIG_SD_BOOT
|
|
puts("SD card\n");
|
|
#endif
|
|
switch (sw) {
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
case 0:
|
|
case 1:
|
|
case 2:
|
|
case 3:
|
|
case 4:
|
|
case 5:
|
|
case 6:
|
|
case 7:
|
|
printf("vBank: %d\n", sw);
|
|
break;
|
|
case 8:
|
|
puts("PromJet\n");
|
|
break;
|
|
case 15:
|
|
puts("IFCCard\n");
|
|
break;
|
|
case 14:
|
|
#else
|
|
case 0:
|
|
#endif
|
|
puts("QSPI:");
|
|
sw = QIXIS_READ(brdcfg[0]);
|
|
sw = (sw & QIXIS_QMAP_MASK) >> QIXIS_QMAP_SHIFT;
|
|
if (sw == 0 || sw == 4)
|
|
puts("0\n");
|
|
else if (sw == 1)
|
|
puts("1\n");
|
|
else
|
|
puts("EMU\n");
|
|
break;
|
|
|
|
default:
|
|
printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
|
|
break;
|
|
}
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
printf("FPGA: v%d (%s), build %d",
|
|
(int)QIXIS_READ(scver), qixis_read_tag(buf),
|
|
(int)qixis_read_minor());
|
|
/* the timestamp string contains "\n" at the end */
|
|
printf(" on %s", qixis_read_time(buf));
|
|
#else
|
|
printf("CPLD: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));
|
|
#endif
|
|
|
|
/*
|
|
* Display the actual SERDES reference clocks as configured by the
|
|
* dip switches on the board. Note that the SWx registers could
|
|
* technically be set to force the reference clocks to match the
|
|
* values that the SERDES expects (or vice versa). For now, however,
|
|
* we just display both values and hope the user notices when they
|
|
* don't match.
|
|
*/
|
|
puts("SERDES1 Reference : ");
|
|
sw = QIXIS_READ(brdcfg[2]);
|
|
clock = (sw >> 6) & 3;
|
|
printf("Clock1 = %sMHz ", freq[clock]);
|
|
clock = (sw >> 4) & 3;
|
|
printf("Clock2 = %sMHz", freq[clock]);
|
|
|
|
puts("\nSERDES2 Reference : ");
|
|
clock = (sw >> 2) & 3;
|
|
printf("Clock1 = %sMHz ", freq[clock]);
|
|
clock = (sw >> 0) & 3;
|
|
printf("Clock2 = %sMHz\n", freq[clock]);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
bool if_board_diff_clk(void)
|
|
{
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
u8 diff_conf = QIXIS_READ(brdcfg[11]);
|
|
return diff_conf & 0x40;
|
|
#else
|
|
u8 diff_conf = QIXIS_READ(dutcfg[11]);
|
|
return diff_conf & 0x80;
|
|
#endif
|
|
}
|
|
|
|
unsigned long get_board_sys_clk(void)
|
|
{
|
|
u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
|
|
|
|
switch (sysclk_conf & 0x0f) {
|
|
case QIXIS_SYSCLK_83:
|
|
return 83333333;
|
|
case QIXIS_SYSCLK_100:
|
|
return 100000000;
|
|
case QIXIS_SYSCLK_125:
|
|
return 125000000;
|
|
case QIXIS_SYSCLK_133:
|
|
return 133333333;
|
|
case QIXIS_SYSCLK_150:
|
|
return 150000000;
|
|
case QIXIS_SYSCLK_160:
|
|
return 160000000;
|
|
case QIXIS_SYSCLK_166:
|
|
return 166666666;
|
|
}
|
|
|
|
return 66666666;
|
|
}
|
|
|
|
unsigned long get_board_ddr_clk(void)
|
|
{
|
|
u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
|
|
|
|
if (if_board_diff_clk())
|
|
return get_board_sys_clk();
|
|
switch ((ddrclk_conf & 0x30) >> 4) {
|
|
case QIXIS_DDRCLK_100:
|
|
return 100000000;
|
|
case QIXIS_DDRCLK_125:
|
|
return 125000000;
|
|
case QIXIS_DDRCLK_133:
|
|
return 133333333;
|
|
}
|
|
|
|
return 66666666;
|
|
}
|
|
|
|
int select_i2c_ch_pca9547(u8 ch)
|
|
{
|
|
int ret;
|
|
|
|
ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
|
|
if (ret) {
|
|
puts("PCA: failed to select proper channel\n");
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#if !defined(CONFIG_SPL_BUILD)
|
|
void board_retimer_init(void)
|
|
{
|
|
u8 reg;
|
|
|
|
/* Retimer is connected to I2C1_CH5 */
|
|
select_i2c_ch_pca9547(I2C_MUX_CH5);
|
|
|
|
/* Access to Control/Shared register */
|
|
reg = 0x0;
|
|
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
|
|
|
|
/* Read device revision and ID */
|
|
i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1);
|
|
debug("Retimer version id = 0x%x\n", reg);
|
|
|
|
/* Enable Broadcast. All writes target all channel register sets */
|
|
reg = 0x0c;
|
|
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
|
|
|
|
/* Reset Channel Registers */
|
|
i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1);
|
|
reg |= 0x4;
|
|
i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1);
|
|
|
|
/* Set data rate as 10.3125 Gbps */
|
|
reg = 0x90;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1);
|
|
reg = 0xb3;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1);
|
|
reg = 0x90;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1);
|
|
reg = 0xb3;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1);
|
|
reg = 0xcd;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1);
|
|
|
|
/* Select VCO Divider to full rate (000) */
|
|
i2c_read(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
|
|
reg &= 0x0f;
|
|
reg |= 0x70;
|
|
i2c_write(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
/* Retimer is connected to I2C1_CH5 */
|
|
select_i2c_ch_pca9547(I2C_MUX_CH5);
|
|
|
|
/* Access to Control/Shared register */
|
|
reg = 0x0;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, ®, 1);
|
|
|
|
/* Read device revision and ID */
|
|
i2c_read(I2C_RETIMER_ADDR2, 1, 1, ®, 1);
|
|
debug("Retimer version id = 0x%x\n", reg);
|
|
|
|
/* Enable Broadcast. All writes target all channel register sets */
|
|
reg = 0x0c;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, ®, 1);
|
|
|
|
/* Reset Channel Registers */
|
|
i2c_read(I2C_RETIMER_ADDR2, 0, 1, ®, 1);
|
|
reg |= 0x4;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0, 1, ®, 1);
|
|
|
|
/* Set data rate as 10.3125 Gbps */
|
|
reg = 0x90;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x60, 1, ®, 1);
|
|
reg = 0xb3;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x61, 1, ®, 1);
|
|
reg = 0x90;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x62, 1, ®, 1);
|
|
reg = 0xb3;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x63, 1, ®, 1);
|
|
reg = 0xcd;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x64, 1, ®, 1);
|
|
|
|
/* Select VCO Divider to full rate (000) */
|
|
i2c_read(I2C_RETIMER_ADDR2, 0x2F, 1, ®, 1);
|
|
reg &= 0x0f;
|
|
reg |= 0x70;
|
|
i2c_write(I2C_RETIMER_ADDR2, 0x2F, 1, ®, 1);
|
|
#endif
|
|
/*return the default channel*/
|
|
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
|
|
}
|
|
|
|
#ifdef CONFIG_MISC_INIT_R
|
|
int misc_init_r(void)
|
|
{
|
|
#ifdef CONFIG_TARGET_LS1088ARDB
|
|
u8 brdcfg5;
|
|
|
|
if (hwconfig("esdhc-force-sd")) {
|
|
brdcfg5 = QIXIS_READ(brdcfg[5]);
|
|
brdcfg5 &= ~BRDCFG5_SPISDHC_MASK;
|
|
brdcfg5 |= BRDCFG5_FORCE_SD;
|
|
QIXIS_WRITE(brdcfg[5], brdcfg5);
|
|
}
|
|
#endif
|
|
return 0;
|
|
}
|
|
#endif
|
|
#endif
|
|
|
|
int i2c_multiplexer_select_vid_channel(u8 channel)
|
|
{
|
|
return select_i2c_ch_pca9547(channel);
|
|
}
|
|
|
|
#ifdef CONFIG_TARGET_LS1088AQDS
|
|
/* read the current value(SVDD) of the LTM Regulator Voltage */
|
|
int get_serdes_volt(void)
|
|
{
|
|
int ret, vcode = 0;
|
|
u8 chan = PWM_CHANNEL0;
|
|
|
|
/* Select the PAGE 0 using PMBus commands PAGE for VDD */
|
|
ret = i2c_write(I2C_SVDD_MONITOR_ADDR,
|
|
PMBUS_CMD_PAGE, 1, &chan, 1);
|
|
if (ret) {
|
|
printf("VID: failed to select VDD Page 0\n");
|
|
return ret;
|
|
}
|
|
|
|
/* Read the output voltage using PMBus command READ_VOUT */
|
|
ret = i2c_read(I2C_SVDD_MONITOR_ADDR,
|
|
PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2);
|
|
if (ret) {
|
|
printf("VID: failed to read the volatge\n");
|
|
return ret;
|
|
}
|
|
|
|
return vcode;
|
|
}
|
|
|
|
int set_serdes_volt(int svdd)
|
|
{
|
|
int ret, vdd_last;
|
|
u8 buff[5] = {0x04, PWM_CHANNEL0, PMBUS_CMD_VOUT_COMMAND,
|
|
svdd & 0xFF, (svdd & 0xFF00) >> 8};
|
|
|
|
/* Write the desired voltage code to the SVDD regulator */
|
|
ret = i2c_write(I2C_SVDD_MONITOR_ADDR,
|
|
PMBUS_CMD_PAGE_PLUS_WRITE, 1, (void *)&buff, 5);
|
|
if (ret) {
|
|
printf("VID: I2C failed to write to the volatge regulator\n");
|
|
return -1;
|
|
}
|
|
|
|
/* Wait for the volatge to get to the desired value */
|
|
do {
|
|
vdd_last = get_serdes_volt();
|
|
if (vdd_last < 0) {
|
|
printf("VID: Couldn't read sensor abort VID adjust\n");
|
|
return -1;
|
|
}
|
|
} while (vdd_last != svdd);
|
|
|
|
return 1;
|
|
}
|
|
#else
|
|
int get_serdes_volt(void)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
int set_serdes_volt(int svdd)
|
|
{
|
|
int ret;
|
|
u8 brdcfg4;
|
|
|
|
printf("SVDD changing of RDB\n");
|
|
|
|
/* Read the BRDCFG54 via CLPD */
|
|
ret = i2c_read(CONFIG_SYS_I2C_FPGA_ADDR,
|
|
QIXIS_BRDCFG4_OFFSET, 1, (void *)&brdcfg4, 1);
|
|
if (ret) {
|
|
printf("VID: I2C failed to read the CPLD BRDCFG4\n");
|
|
return -1;
|
|
}
|
|
|
|
brdcfg4 = brdcfg4 | 0x08;
|
|
|
|
/* Write to the BRDCFG4 */
|
|
ret = i2c_write(CONFIG_SYS_I2C_FPGA_ADDR,
|
|
QIXIS_BRDCFG4_OFFSET, 1, (void *)&brdcfg4, 1);
|
|
if (ret) {
|
|
debug("VID: I2C failed to set the SVDD CPLD BRDCFG4\n");
|
|
return -1;
|
|
}
|
|
|
|
/* Wait for the volatge to get to the desired value */
|
|
udelay(10000);
|
|
|
|
return 1;
|
|
}
|
|
#endif
|
|
|
|
/* this function disables the SERDES, changes the SVDD Voltage and enables it*/
|
|
int board_adjust_vdd(int vdd)
|
|
{
|
|
int ret = 0;
|
|
|
|
debug("%s: vdd = %d\n", __func__, vdd);
|
|
|
|
/* Special settings to be performed when voltage is 900mV */
|
|
if (vdd == 900) {
|
|
ret = setup_serdes_volt(vdd);
|
|
if (ret < 0) {
|
|
ret = -1;
|
|
goto exit;
|
|
}
|
|
}
|
|
exit:
|
|
return ret;
|
|
}
|
|
|
|
#if !defined(CONFIG_SPL_BUILD)
|
|
int board_init(void)
|
|
{
|
|
init_final_memctl_regs();
|
|
#if defined(CONFIG_TARGET_LS1088ARDB) && defined(CONFIG_FSL_MC_ENET)
|
|
u32 __iomem *irq_ccsr = (u32 __iomem *)ISC_BASE;
|
|
#endif
|
|
|
|
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
|
|
board_retimer_init();
|
|
|
|
#ifdef CONFIG_ENV_IS_NOWHERE
|
|
gd->env_addr = (ulong)&default_environment[0];
|
|
#endif
|
|
|
|
#if defined(CONFIG_TARGET_LS1088ARDB) && defined(CONFIG_FSL_MC_ENET)
|
|
/* invert AQR105 IRQ pins polarity */
|
|
out_le32(irq_ccsr + IRQCR_OFFSET / 4, AQR105_IRQ_MASK);
|
|
#endif
|
|
|
|
#ifdef CONFIG_FSL_CAAM
|
|
sec_init();
|
|
#endif
|
|
#ifdef CONFIG_FSL_LS_PPA
|
|
ppa_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
void detail_board_ddr_info(void)
|
|
{
|
|
puts("\nDDR ");
|
|
print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
|
|
print_ddr_info(0);
|
|
}
|
|
|
|
#if defined(CONFIG_ARCH_MISC_INIT)
|
|
int arch_misc_init(void)
|
|
{
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_FSL_MC_ENET
|
|
void fdt_fixup_board_enet(void *fdt)
|
|
{
|
|
int offset;
|
|
|
|
offset = fdt_path_offset(fdt, "/fsl-mc");
|
|
|
|
if (offset < 0)
|
|
offset = fdt_path_offset(fdt, "/fsl,dprc@0");
|
|
|
|
if (offset < 0) {
|
|
printf("%s: ERROR: fsl-mc node not found in device tree (error %d)\n",
|
|
__func__, offset);
|
|
return;
|
|
}
|
|
|
|
if ((get_mc_boot_status() == 0) && (get_dpl_apply_status() == 0))
|
|
fdt_status_okay(fdt, offset);
|
|
else
|
|
fdt_status_fail(fdt, offset);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_OF_BOARD_SETUP
|
|
void fsl_fdt_fixup_flash(void *fdt)
|
|
{
|
|
int offset;
|
|
|
|
/*
|
|
* IFC-NOR and QSPI are muxed on SoC.
|
|
* So disable IFC node in dts if QSPI is enabled or
|
|
* disable QSPI node in dts in case QSPI is not enabled.
|
|
*/
|
|
|
|
#ifdef CONFIG_FSL_QSPI
|
|
offset = fdt_path_offset(fdt, "/soc/ifc/nor");
|
|
|
|
if (offset < 0)
|
|
offset = fdt_path_offset(fdt, "/ifc/nor");
|
|
#else
|
|
offset = fdt_path_offset(fdt, "/soc/quadspi");
|
|
|
|
if (offset < 0)
|
|
offset = fdt_path_offset(fdt, "/quadspi");
|
|
#endif
|
|
if (offset < 0)
|
|
return;
|
|
|
|
fdt_status_disabled(fdt, offset);
|
|
}
|
|
|
|
int ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
int err, i;
|
|
u64 base[CONFIG_NR_DRAM_BANKS];
|
|
u64 size[CONFIG_NR_DRAM_BANKS];
|
|
|
|
ft_cpu_setup(blob, bd);
|
|
|
|
/* fixup DT for the two GPP DDR banks */
|
|
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
|
|
base[i] = gd->bd->bi_dram[i].start;
|
|
size[i] = gd->bd->bi_dram[i].size;
|
|
}
|
|
|
|
#ifdef CONFIG_RESV_RAM
|
|
/* reduce size if reserved memory is within this bank */
|
|
if (gd->arch.resv_ram >= base[0] &&
|
|
gd->arch.resv_ram < base[0] + size[0])
|
|
size[0] = gd->arch.resv_ram - base[0];
|
|
else if (gd->arch.resv_ram >= base[1] &&
|
|
gd->arch.resv_ram < base[1] + size[1])
|
|
size[1] = gd->arch.resv_ram - base[1];
|
|
#endif
|
|
|
|
fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS);
|
|
|
|
fsl_fdt_fixup_flash(blob);
|
|
|
|
#ifdef CONFIG_FSL_MC_ENET
|
|
fdt_fixup_board_enet(blob);
|
|
err = fsl_mc_ldpaa_exit(bd);
|
|
if (err)
|
|
return err;
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
#endif /* defined(CONFIG_SPL_BUILD) */
|