mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-06-09 23:36:03 +09:00
58f449676a
The board is manufactured by Digilent Main features: - Soc: XC7Z010 (Z7-10) or XC7Z020 (Z7-20) - RAM: 1 GB DDR3L - FLASH: 16 MB QSPI - 1 Gbps Ethernet - USB 2.0 - microSD slot - Pcam camera connector - HDMI Tx and Rx - Audio codec: stereo out, stereo in, mic - 5 (Z7-10) or 6 (Z7-20) Pmod ports - 6 push-buttons, 4 switches, 5 LEDs - 1 (Z7-10) or 2 (Z7-20) RGB LEDs Signed-off-by: Luis Araneda <luaraneda@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
82 lines
1.2 KiB
Plaintext
82 lines
1.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2011 - 2015 Xilinx
|
|
* Copyright (C) 2012 National Instruments Corp.
|
|
*/
|
|
/dts-v1/;
|
|
#include "zynq-7000.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
model = "Digilent Zybo Z7 board";
|
|
compatible = "digilent,zynq-zybo-z7", "xlnx,zynq-7000";
|
|
|
|
aliases {
|
|
ethernet0 = &gem0;
|
|
serial0 = &uart1;
|
|
spi0 = &qspi;
|
|
mmc0 = &sdhci0;
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x40000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
ld4 {
|
|
label = "zynq-zybo-z7:green:ld4";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
usb_phy0: phy0 {
|
|
#phy-cells = <0>;
|
|
compatible = "usb-nop-xceiv";
|
|
reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
&clkc {
|
|
ps-clk-frequency = <33333333>;
|
|
};
|
|
|
|
&gem0 {
|
|
status = "okay";
|
|
phy-mode = "rgmii-id";
|
|
phy-handle = <ðernet_phy>;
|
|
|
|
ethernet_phy: ethernet-phy@0 {
|
|
reg = <0>;
|
|
device_type = "ethernet-phy";
|
|
};
|
|
};
|
|
|
|
&qspi {
|
|
u-boot,dm-pre-reloc;
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhci0 {
|
|
u-boot,dm-pre-reloc;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart1 {
|
|
u-boot,dm-pre-reloc;
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
dr_mode = "host";
|
|
usb-phy = <&usb_phy0>;
|
|
};
|