u-boot-brain/board/freescale/mpc8572ds/mpc8572ds.c
Timur Tabi 5d065c3e10 powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
Most 85xx boards can be built as a 32-bit or a 36-bit.  Current code sometimes
displays which of these is actually built, but it's inconsistent.  This is
especially problematic since the "default" build for a given 85xx board can
be either one, so if you don't see a message, you can't always know which
size is being used.  Not only that, but each board includes code that displays
the message, so there is duplication.

The 'bdinfo' command has been updated to display this information, so
we don't need to display it at boot time.  The board-specific code is
deleted.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:34 -05:00

264 lines
6.2 KiB
C

/*
* Copyright 2007-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <command.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <miiphy.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <tsec.h>
#include <fsl_mdio.h>
#include <netdev.h>
#include "../common/sgmii_riser.h"
int checkboard (void)
{
u8 vboot;
u8 *pixis_base = (u8 *)PIXIS_BASE;
printf("Board: MPC8572DS Sys ID: 0x%02x, "
"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
in_8(pixis_base + PIXIS_PVER));
vboot = in_8(pixis_base + PIXIS_VBOOT);
switch ((vboot & PIXIS_VBOOT_LBMAP) >> 6) {
case PIXIS_VBOOT_LBMAP_NOR0:
puts ("vBank: 0\n");
break;
case PIXIS_VBOOT_LBMAP_PJET:
puts ("Promjet\n");
break;
case PIXIS_VBOOT_LBMAP_NAND:
puts ("NAND\n");
break;
case PIXIS_VBOOT_LBMAP_NOR1:
puts ("vBank: 1\n");
break;
}
return 0;
}
#if !defined(CONFIG_SPD_EEPROM)
/*
* Fixed sdram init -- doesn't use serial presence detect.
*/
phys_size_t fixed_sdram (void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_ddr_t *ddr= &immap->im_ddr;
uint d_init;
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1;
ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2;
ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT;
ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL;
ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2;
#if defined (CONFIG_DDR_ECC)
ddr->err_int_en = CONFIG_SYS_DDR_ERR_INT_EN;
ddr->err_disable = CONFIG_SYS_DDR_ERR_DIS;
ddr->err_sbe = CONFIG_SYS_DDR_SBE;
#endif
asm("sync;isync");
udelay(500);
ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
d_init = 1;
debug("DDR - 1st controller: memory initializing\n");
/*
* Poll until memory is initialized.
* 512 Meg at 400 might hit this 200 times or so.
*/
while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) {
udelay(1000);
}
debug("DDR: memory initialized\n\n");
asm("sync; isync");
udelay(500);
#endif
return 512 * 1024 * 1024;
}
#endif
#ifdef CONFIG_PCI
void pci_init_board(void)
{
struct pci_controller *hose;
fsl_pcie_init_board(0);
hose = find_hose_by_cfg_addr((void *)(CONFIG_SYS_PCIE3_ADDR));
if (hose) {
u32 temp32;
u8 uli_busno = hose->first_busno + 2;
/*
* Activate ULI1575 legacy chip by performing a fake
* memory access. Needed to make ULI RTC work.
* Device 1d has the first on-board memory BAR.
*/
pci_hose_read_config_dword(hose, PCI_BDF(uli_busno, 0x1d, 0),
PCI_BASE_ADDRESS_1, &temp32);
if (temp32 >= CONFIG_SYS_PCIE3_MEM_BUS) {
void *p = pci_mem_to_virt(PCI_BDF(uli_busno, 0x1d, 0),
temp32, 4, 0);
debug(" uli1572 read to %p\n", p);
in_be32(p);
}
}
}
#endif
int board_early_init_r(void)
{
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
/*
* Remap Boot flash + PROMJET region to caching-inhibited
* so that flash can be erased properly.
*/
/* Flush d-cache and invalidate i-cache of any FLASH data */
flush_dcache();
invalidate_icache();
/* invalidate existing TLB entry for flash + promjet */
disable_tlb(flash_esel);
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */
0, flash_esel, BOOKE_PAGESZ_256M, 1); /* ts, esel, tsize, iprot */
return 0;
}
#ifdef CONFIG_TSEC_ENET
int board_eth_init(bd_t *bis)
{
struct fsl_pq_mdio_info mdio_info;
struct tsec_info_struct tsec_info[4];
int num = 0;
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
if (is_serdes_configured(SGMII_TSEC1)) {
puts("eTSEC1 is in sgmii mode.\n");
tsec_info[num].flags |= TSEC_SGMII;
}
num++;
#endif
#ifdef CONFIG_TSEC2
SET_STD_TSEC_INFO(tsec_info[num], 2);
if (is_serdes_configured(SGMII_TSEC2)) {
puts("eTSEC2 is in sgmii mode.\n");
tsec_info[num].flags |= TSEC_SGMII;
}
num++;
#endif
#ifdef CONFIG_TSEC3
SET_STD_TSEC_INFO(tsec_info[num], 3);
if (is_serdes_configured(SGMII_TSEC3)) {
puts("eTSEC3 is in sgmii mode.\n");
tsec_info[num].flags |= TSEC_SGMII;
}
num++;
#endif
#ifdef CONFIG_TSEC4
SET_STD_TSEC_INFO(tsec_info[num], 4);
if (is_serdes_configured(SGMII_TSEC4)) {
puts("eTSEC4 is in sgmii mode.\n");
tsec_info[num].flags |= TSEC_SGMII;
}
num++;
#endif
if (!num) {
printf("No TSECs initialized\n");
return 0;
}
#ifdef CONFIG_FSL_SGMII_RISER
fsl_sgmii_riser_init(tsec_info, num);
#endif
mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
mdio_info.name = DEFAULT_MII_NAME;
fsl_pq_mdio_init(bis, &mdio_info);
tsec_eth_init(bis, tsec_info, num);
return pci_eth_init(bis);
}
#endif
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
phys_addr_t base;
phys_size_t size;
ft_cpu_setup(blob, bd);
base = getenv_bootm_low();
size = getenv_bootm_size();
fdt_fixup_memory(blob, (u64)base, (u64)size);
FT_FSL_PCI_SETUP;
#ifdef CONFIG_FSL_SGMII_RISER
fsl_sgmii_riser_fdt_fixup(blob);
#endif
}
#endif