mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-22 09:58:52 +09:00
![Joe Hershberger](/assets/img/avatar_default.png)
This value is not used by the network stack and is available in the global data, so stop passing it around. For the one legacy function that still expects it (init op on old Ethernet drivers) pass in the global pointer version directly to avoid changing that interface. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reported-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> (Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
282 lines
7.5 KiB
C
282 lines
7.5 KiB
C
/*
|
|
* (C) Copyright 2007-2008
|
|
* Stelian Pop <stelian@popies.net>
|
|
* Lead Tech Design <www.leadtechdesign.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/at91sam9261.h>
|
|
#include <asm/arch/at91sam9261_matrix.h>
|
|
#include <asm/arch/at91sam9_smc.h>
|
|
#include <asm/arch/at91_common.h>
|
|
#include <asm/arch/at91_pmc.h>
|
|
#include <asm/arch/at91_rstc.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <lcd.h>
|
|
#include <atmel_lcdc.h>
|
|
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#endif
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
/*
|
|
* Miscelaneous platform dependent initialisations
|
|
*/
|
|
|
|
#ifdef CONFIG_CMD_NAND
|
|
static void at91sam9261ek_nand_hw_init(void)
|
|
{
|
|
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
|
|
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
|
|
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
|
|
unsigned long csa;
|
|
|
|
/* Enable CS3 */
|
|
csa = readl(&matrix->ebicsa);
|
|
csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
|
|
|
|
writel(csa, &matrix->ebicsa);
|
|
|
|
/* Configure SMC CS3 for NAND/SmartMedia */
|
|
#ifdef CONFIG_AT91SAM9G10EK
|
|
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[3].setup);
|
|
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) |
|
|
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7),
|
|
&smc->cs[3].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
|
|
&smc->cs[3].cycle);
|
|
#else
|
|
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[3].setup);
|
|
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
|
|
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
|
|
&smc->cs[3].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
|
|
&smc->cs[3].cycle);
|
|
#endif
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
#ifdef CONFIG_SYS_NAND_DBW_16
|
|
AT91_SMC_MODE_DBW_16 |
|
|
#else /* CONFIG_SYS_NAND_DBW_8 */
|
|
AT91_SMC_MODE_DBW_8 |
|
|
#endif
|
|
AT91_SMC_MODE_TDF_CYCLE(2),
|
|
&smc->cs[3].mode);
|
|
|
|
writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
|
|
|
|
/* Configure RDY/BSY */
|
|
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
|
|
|
|
/* Enable NandFlash */
|
|
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
|
|
|
|
at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */
|
|
at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
static void at91sam9261ek_dm9000_hw_init(void)
|
|
{
|
|
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
|
|
|
|
/* Configure SMC CS2 for DM9000 */
|
|
#ifdef CONFIG_AT91SAM9G10EK
|
|
writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[2].setup);
|
|
writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) |
|
|
AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8),
|
|
&smc->cs[2].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20),
|
|
&smc->cs[2].cycle);
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
|
|
AT91_SMC_MODE_TDF_CYCLE(1),
|
|
&smc->cs[2].mode);
|
|
#else
|
|
writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[2].setup);
|
|
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
|
|
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
|
|
&smc->cs[2].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
|
|
&smc->cs[2].cycle);
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
|
|
AT91_SMC_MODE_TDF_CYCLE(1),
|
|
&smc->cs[2].mode);
|
|
#endif
|
|
|
|
/* Configure Reset signal as output */
|
|
at91_set_gpio_output(AT91_PIN_PC10, 0);
|
|
|
|
/* Configure Interrupt pin as input, no pull-up */
|
|
at91_set_gpio_input(AT91_PIN_PC11, 0);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_LCD
|
|
vidinfo_t panel_info = {
|
|
.vl_col = 240,
|
|
.vl_row = 320,
|
|
.vl_clk = 4965000,
|
|
.vl_sync = ATMEL_LCDC_INVLINE_INVERTED |
|
|
ATMEL_LCDC_INVFRAME_INVERTED,
|
|
.vl_bpix = 3,
|
|
.vl_tft = 1,
|
|
.vl_hsync_len = 5,
|
|
.vl_left_margin = 1,
|
|
.vl_right_margin = 33,
|
|
.vl_vsync_len = 1,
|
|
.vl_upper_margin = 1,
|
|
.vl_lower_margin = 0,
|
|
.mmio = ATMEL_BASE_LCDC,
|
|
};
|
|
|
|
void lcd_enable(void)
|
|
{
|
|
at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
|
|
}
|
|
|
|
void lcd_disable(void)
|
|
{
|
|
at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
|
|
}
|
|
|
|
static void at91sam9261ek_lcd_hw_init(void)
|
|
{
|
|
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
|
|
|
|
at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */
|
|
at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */
|
|
at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */
|
|
at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */
|
|
at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */
|
|
at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */
|
|
at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */
|
|
at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */
|
|
at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */
|
|
at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */
|
|
at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */
|
|
at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */
|
|
at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */
|
|
at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */
|
|
at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */
|
|
at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */
|
|
at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */
|
|
at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */
|
|
at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */
|
|
at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */
|
|
at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */
|
|
at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */
|
|
|
|
writel(AT91_PMC_HCK1, &pmc->scer);
|
|
|
|
/* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */
|
|
#ifdef CONFIG_AT91SAM9261EK
|
|
gd->fb_base = ATMEL_BASE_SRAM;
|
|
#endif
|
|
}
|
|
|
|
#ifdef CONFIG_LCD_INFO
|
|
#include <nand.h>
|
|
#include <version.h>
|
|
|
|
void lcd_show_board_info(void)
|
|
{
|
|
ulong dram_size, nand_size;
|
|
int i;
|
|
char temp[32];
|
|
|
|
lcd_printf ("%s\n", U_BOOT_VERSION);
|
|
lcd_printf ("(C) 2008 ATMEL Corp\n");
|
|
lcd_printf ("at91support@atmel.com\n");
|
|
lcd_printf ("%s CPU at %s MHz\n",
|
|
ATMEL_CPU_NAME,
|
|
strmhz(temp, get_cpu_clk_rate()));
|
|
|
|
dram_size = 0;
|
|
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
|
|
dram_size += gd->bd->bi_dram[i].size;
|
|
nand_size = 0;
|
|
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
|
|
nand_size += nand_info[i].size;
|
|
lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
|
|
dram_size >> 20,
|
|
nand_size >> 20 );
|
|
}
|
|
#endif /* CONFIG_LCD_INFO */
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
#ifdef CONFIG_AT91SAM9G10EK
|
|
/* arch number of AT91SAM9G10EK-Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK;
|
|
#else
|
|
/* arch number of AT91SAM9261EK-Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
|
|
#endif
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
at91_seriald_hw_init();
|
|
#ifdef CONFIG_CMD_NAND
|
|
at91sam9261ek_nand_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_HAS_DATAFLASH
|
|
at91_spi0_hw_init(1 << 0);
|
|
#endif
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
at91sam9261ek_dm9000_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_LCD
|
|
at91sam9261ek_lcd_hw_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
return dm9000_initialize(bis);
|
|
}
|
|
#endif
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
|
|
CONFIG_SYS_SDRAM_SIZE);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
void reset_phy(void)
|
|
{
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
/*
|
|
* Initialize ethernet HW addr prior to starting Linux,
|
|
* needed for nfsroot
|
|
*/
|
|
eth_init();
|
|
#endif
|
|
}
|
|
#endif
|