mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-18 07:58:52 +09:00
![Masahiro Yamada](/assets/img/avatar_default.png)
We do not have to define CONFIG_4xx in board config headers because it is defined in arch/powerpc/cpu/ppc4xx/config.mk. include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx". I believe it is a typo because "CONFIG_4x" is not used at all in other files. So, I also deleted "CONFIG_4x" in include/configs/JSE.h. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
318 lines
11 KiB
C
318 lines
11 KiB
C
/*
|
|
* (C) Copyright 2001
|
|
* Erik Theisen, Wave 7 Optics, etheisen@mindspring.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_405GP 1 /* This is a PPC405GP CPU */
|
|
#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */
|
|
#define CONFIG_W7OLMG 1 /* ...specifically an LMG */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */
|
|
#define CONFIG_MISC_INIT_R 1 /* and misc_init_r() */
|
|
|
|
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
|
|
|
|
#define CONFIG_BAUDRATE 9600
|
|
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
|
|
|
|
#if 1
|
|
#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */
|
|
#else
|
|
#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
|
|
#endif
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_LOADADDR F0080000
|
|
|
|
#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */
|
|
#define CONFIG_OVERWRITE_ETHADDR_ONCE
|
|
#define CONFIG_IPADDR 192.168.1.1
|
|
#define CONFIG_NETMASK 255.255.255.0
|
|
#define CONFIG_SERVERIP 192.168.1.2
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* disallow baudrate change */
|
|
|
|
#define CONFIG_PPC4xx_EMAC
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_PHY_ADDR 0 /* PHY address */
|
|
|
|
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
|
|
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
|
|
#define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */
|
|
#define CONFIG_SYS_DTT_MAX_TEMP 70
|
|
#define CONFIG_SYS_DTT_LOW_TEMP -30
|
|
#define CONFIG_SYS_DTT_HYSTERESIS 3
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_PCI
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_ASKENV
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_BEDBUG
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_BSP
|
|
#define CONFIG_CMD_REGINFO
|
|
#define CONFIG_CMD_DTT
|
|
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */
|
|
|
|
#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */
|
|
#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "Wave7Optics> " /* Monitor Command Prompt */
|
|
#undef CONFIG_SYS_HUSH_PARSER /* No hush parse for U-Boot */
|
|
#ifdef CONFIG_SYS_HUSH_PARSER
|
|
#endif
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
|
|
|
|
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
|
|
#define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
|
|
#define CONFIG_SYS_BASE_BAUD 384000
|
|
|
|
|
|
/* The following table includes the supported baudrates */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE {9600}
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCI stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
|
|
#define PCI_HOST_FORCE 1 /* configure as pci host */
|
|
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
|
|
|
|
#define CONFIG_PCI /* include pci support */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
|
|
#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
|
|
#define CONFIG_PCI_PNP /* pci plug-and-play */
|
|
/* resource configuration */
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */
|
|
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */
|
|
#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
|
|
#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
|
|
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
|
|
#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
|
|
#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
|
|
#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Set up values for external bus controller
|
|
* used by cpu_init.c
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
/* use PerWE instead of PCI_INT ( these functions share a pin ) */
|
|
#define CONFIG_USE_PERWE 1
|
|
|
|
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
|
|
#define CONFIG_SYS_TEMP_STACK_OCM 1
|
|
|
|
/* bank 0 is boot flash */
|
|
/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
|
|
#define CONFIG_SYS_W7O_EBC_PB0AP 0x03050440
|
|
/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */
|
|
#define CONFIG_SYS_W7O_EBC_PB0CR 0xFFE38000
|
|
|
|
/* bank 1 is main flash */
|
|
/* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */
|
|
#define CONFIG_SYS_EBC_PB1AP 0x04850240
|
|
/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */
|
|
#define CONFIG_SYS_EBC_PB1CR 0xF00FC000
|
|
|
|
/* bank 2 is RTC/NVRAM */
|
|
/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
|
|
#define CONFIG_SYS_EBC_PB2AP 0x03000440
|
|
/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */
|
|
#define CONFIG_SYS_EBC_PB2CR 0xFC018000
|
|
|
|
/* bank 3 is FPGA 0 */
|
|
/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */
|
|
#define CONFIG_SYS_EBC_PB3AP 0x02000400
|
|
/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */
|
|
#define CONFIG_SYS_EBC_PB3CR 0xFD01A000
|
|
|
|
/* bank 4 is SAM 8 bit range */
|
|
/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */
|
|
#define CONFIG_SYS_EBC_PB4AP 0x02840380
|
|
/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */
|
|
#define CONFIG_SYS_EBC_PB4CR 0xFE878000
|
|
|
|
/* bank 5 is SAM 16 bit range */
|
|
/* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */
|
|
#define CONFIG_SYS_EBC_PB5AP 0x05040d80
|
|
/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */
|
|
#define CONFIG_SYS_EBC_PB5CR 0xFD87A000
|
|
|
|
/* bank 6 is unused */
|
|
/* PB6AP = 0 */
|
|
#define CONFIG_SYS_EBC_PB6AP 0x00000000
|
|
/* PB6CR = 0 */
|
|
#define CONFIG_SYS_EBC_PB6CR 0x00000000
|
|
|
|
/* bank 7 is LED register */
|
|
/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
|
|
#define CONFIG_SYS_W7O_EBC_PB7AP 0x03050440
|
|
/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */
|
|
#define CONFIG_SYS_W7O_EBC_PB7CR 0xFE01C000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */
|
|
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use real Flash protection */
|
|
|
|
#if 1 /* Use NVRAM for environment variables */
|
|
/*-----------------------------------------------------------------------
|
|
* NVRAM organization
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */
|
|
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */
|
|
#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
|
|
#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
|
|
/*define CONFIG_ENV_ADDR \
|
|
(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */
|
|
#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR
|
|
|
|
#else /* Use Boot Flash for environment variables */
|
|
/*-----------------------------------------------------------------------
|
|
* Flash EEPROM for environment
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
|
|
#define CONFIG_ENV_SIZE 0x10000 /* Total Size of env. sector */
|
|
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* I2C EEPROM (ATMEL 24C04N)
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_PPC4XX
|
|
#define CONFIG_SYS_I2C_PPC4XX_CH0
|
|
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
|
|
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
|
|
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_I2C_MULTI_EEPROMS
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for Serial Presence Detect EEPROM address
|
|
* (to get SDRAM settings)
|
|
*/
|
|
#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*/
|
|
#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */
|
|
#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */
|
|
|
|
/* On Chip Memory location */
|
|
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
|
|
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in RAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#endif
|
|
|
|
/*
|
|
* FPGA(s) configuration
|
|
*/
|
|
#define CONFIG_SYS_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */
|
|
#define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */
|
|
#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */
|
|
#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */
|
|
#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */
|
|
|
|
#endif /* __CONFIG_H */
|