mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-06-09 23:36:03 +09:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
213 lines
5.5 KiB
C
213 lines
5.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Board file for the VInCo platform
|
|
* Based on the the SAMA5-EK board file
|
|
* Configuration settings for the VInCo platform.
|
|
* Copyright (C) 2014 Atmel
|
|
* Bo Shen <voice.shen@atmel.com>
|
|
* Copyright (C) 2015 Free Electrons
|
|
* Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/at91_common.h>
|
|
#include <asm/arch/at91_pmc.h>
|
|
#include <asm/arch/at91_rstc.h>
|
|
#include <asm/arch/atmel_mpddrc.h>
|
|
#include <asm/arch/atmel_usba_udc.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/sama5d3_smc.h>
|
|
#include <asm/arch/sama5d4.h>
|
|
#include <atmel_hlcdc.h>
|
|
#include <atmel_mci.h>
|
|
#include <lcd.h>
|
|
#include <mmc.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <nand.h>
|
|
#include <spi.h>
|
|
#include <version.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* FIXME gpio code here need to handle through DM_GPIO */
|
|
#ifndef CONFIG_DM_SPI
|
|
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
|
|
{
|
|
return bus == 0 && cs == 0;
|
|
}
|
|
|
|
void spi_cs_activate(struct spi_slave *slave)
|
|
{
|
|
at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
|
|
}
|
|
|
|
void spi_cs_deactivate(struct spi_slave *slave)
|
|
{
|
|
at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
|
|
}
|
|
|
|
static void vinco_spi0_hw_init(void)
|
|
{
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */
|
|
|
|
at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */
|
|
|
|
/* Enable clock */
|
|
at91_periph_clk_enable(ATMEL_ID_SPI0);
|
|
}
|
|
#endif /* CONFIG_ATMEL_SPI */
|
|
|
|
|
|
#ifdef CONFIG_CMD_USB
|
|
static void vinco_usb_hw_init(void)
|
|
{
|
|
at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
|
|
at91_set_pio_output(AT91_PIO_PORTE, 12, 0);
|
|
at91_set_pio_output(AT91_PIO_PORTE, 10, 0);
|
|
}
|
|
#endif
|
|
|
|
|
|
#ifdef CONFIG_GENERIC_ATMEL_MCI
|
|
void vinco_mci0_hw_init(void)
|
|
{
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 5, 1); /* MCI0 CDA */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 6, 1); /* MCI0 DA0 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 7, 1); /* MCI0 DA1 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 8, 1); /* MCI0 DA2 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 9, 1); /* MCI0 DA3 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 10, 1); /* MCI0 DA4 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 11, 1); /* MCI0 DA5 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 12, 1); /* MCI0 DA6 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 13, 1); /* MCI0 DA7 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTC, 4, 0); /* MCI0 CLK */
|
|
|
|
/*
|
|
* As the mci io internal pull down is too strong, so if the io needs
|
|
* external pull up, the pull up resistor will be very small, if so
|
|
* the power consumption will increase, so disable the interanl pull
|
|
* down to save the power.
|
|
*/
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 4, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 5, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 6, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 7, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 8, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 9, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 10, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 11, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 12, 0);
|
|
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 13, 0);
|
|
|
|
/* Enable clock */
|
|
at91_periph_clk_enable(ATMEL_ID_MCI0);
|
|
}
|
|
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
/* Enable power for MCI0 interface */
|
|
at91_set_pio_output(AT91_PIO_PORTE, 7, 1);
|
|
|
|
return atmel_mci_init((void *)ATMEL_BASE_MCI0);
|
|
}
|
|
#endif /* CONFIG_GENERIC_ATMEL_MCI */
|
|
|
|
#ifdef CONFIG_MACB
|
|
void vinco_macb0_hw_init(void)
|
|
{
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ETXCK_EREFCK */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 6, 0); /* ERXDV */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ERX0 */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ERX1 */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ERXER */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ETXEN */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX0 */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ETX1 */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 17, 0); /* EMDIO */
|
|
at91_pio3_set_a_periph(AT91_PIO_PORTB, 16, 0); /* EMDC */
|
|
|
|
/* Enable clock */
|
|
at91_periph_clk_enable(ATMEL_ID_GMAC0);
|
|
|
|
/* Enable Phy*/
|
|
at91_set_pio_output(AT91_PIO_PORTE, 8, 1);
|
|
}
|
|
#endif
|
|
|
|
static void vinco_serial3_hw_init(void)
|
|
{
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTE, 17, 1); /* TXD3 */
|
|
at91_pio3_set_b_periph(AT91_PIO_PORTE, 16, 0); /* RXD3 */
|
|
|
|
/* Enable clock */
|
|
at91_periph_clk_enable(ATMEL_ID_USART3);
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
at91_periph_clk_enable(ATMEL_ID_PIOA);
|
|
at91_periph_clk_enable(ATMEL_ID_PIOB);
|
|
at91_periph_clk_enable(ATMEL_ID_PIOC);
|
|
at91_periph_clk_enable(ATMEL_ID_PIOD);
|
|
at91_periph_clk_enable(ATMEL_ID_PIOE);
|
|
|
|
vinco_serial3_hw_init();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
#ifndef CONFIG_DM_SPI
|
|
vinco_spi0_hw_init();
|
|
#endif
|
|
|
|
#ifdef CONFIG_GENERIC_ATMEL_MCI
|
|
vinco_mci0_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_MACB
|
|
vinco_macb0_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_CMD_USB
|
|
vinco_usb_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
|
|
at91_udp_hw_init();
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
|
|
CONFIG_SYS_SDRAM_SIZE);
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int rc = 0;
|
|
|
|
#ifdef CONFIG_MACB
|
|
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
|
|
#endif
|
|
|
|
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
|
|
usba_udc_probe(&pdata);
|
|
#ifdef CONFIG_USB_ETH_RNDIS
|
|
usb_eth_initialize(bis);
|
|
#endif
|
|
#endif
|
|
|
|
return rc;
|
|
}
|