// SPDX-License-Identifier: GPL-2.0+ /* * Copyright (C) 2014 Gateworks Corporation * Copyright (C) 2011-2012 Freescale Semiconductor, Inc. * * Author: Tim Harvey */ #include #include #include #include #include #include #include #include #include DECLARE_GLOBAL_DATA_PTR; __weak int spl_board_boot_device(enum boot_device boot_dev_spl) { return 0; } #if defined(CONFIG_MX6) /* determine boot device from SRC_SBMR1 (BOOT_CFG[4:1]) or SRC_GPR9 register */ u32 spl_boot_device(void) { unsigned int bmode = readl(&src_base->sbmr2); u32 reg = imx6_src_get_boot_mode(); /* * Check for BMODE if serial downloader is enabled * BOOT_MODE - see IMX6DQRM Table 8-1 */ if (((bmode >> 24) & 0x03) == 0x01) /* Serial Downloader */ return BOOT_DEVICE_BOARD; /* * The above method does not detect that the boot ROM used * serial downloader in case the boot ROM decided to use the * serial downloader as a fall back (primary boot source failed). * * Infer that the boot ROM used the USB serial downloader by * checking whether the USB PHY is currently active... This * assumes that SPL did not (yet) initialize the USB PHY... */ if (is_usbotg_phy_active()) return BOOT_DEVICE_BOARD; /* BOOT_CFG1[7:4] - see IMX6DQRM Table 8-8 */ switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) { /* EIM: See 8.5.1, Table 8-9 */ case IMX6_BMODE_EMI: /* BOOT_CFG1[3]: NOR/OneNAND Selection */ switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) { case IMX6_BMODE_ONENAND: return BOOT_DEVICE_ONENAND; case IMX6_BMODE_NOR: return BOOT_DEVICE_NOR; break; } /* Reserved: Used to force Serial Downloader */ case IMX6_BMODE_RESERVED: return BOOT_DEVICE_BOARD; /* SATA: See 8.5.4, Table 8-20 */ #if !defined(CONFIG_MX6UL) && !defined(CONFIG_MX6ULL) case IMX6_BMODE_SATA: return BOOT_DEVICE_SATA; #endif /* Serial ROM: See 8.5.5.1, Table 8-22 */ case IMX6_BMODE_SERIAL_ROM: /* BOOT_CFG4[2:0] */ switch ((reg & IMX6_BMODE_SERIAL_ROM_MASK) >> IMX6_BMODE_SERIAL_ROM_SHIFT) { case IMX6_BMODE_ECSPI1: case IMX6_BMODE_ECSPI2: case IMX6_BMODE_ECSPI3: case IMX6_BMODE_ECSPI4: case IMX6_BMODE_ECSPI5: return BOOT_DEVICE_SPI; case IMX6_BMODE_I2C1: case IMX6_BMODE_I2C2: case IMX6_BMODE_I2C3: return BOOT_DEVICE_I2C; } break; /* SD/eSD: 8.5.3, Table 8-15 */ case IMX6_BMODE_SD: case IMX6_BMODE_ESD: return BOOT_DEVICE_MMC1; /* MMC/eMMC: 8.5.3 */ case IMX6_BMODE_MMC: case IMX6_BMODE_EMMC: return BOOT_DEVICE_MMC1; /* NAND Flash: 8.5.2, Table 8-10 */ case IMX6_BMODE_NAND_MIN ... IMX6_BMODE_NAND_MAX: return BOOT_DEVICE_NAND; #if defined(CONFIG_MX6UL) || defined(CONFIG_MX6ULL) /* QSPI boot */ case IMX6_BMODE_QSPI: return BOOT_DEVICE_SPI; #endif } return BOOT_DEVICE_NONE; } #elif defined(CONFIG_MX7) || defined(CONFIG_IMX8M) || defined(CONFIG_IMX8) /* Translate iMX7/i.MX8M boot device to the SPL boot device enumeration */ u32 spl_boot_device(void) { #if defined(CONFIG_MX7) unsigned int bmode = readl(&src_base->sbmr2); /* * Check for BMODE if serial downloader is enabled * BOOT_MODE - see IMX7DRM Table 6-24 */ if (((bmode >> 24) & 0x03) == 0x01) /* Serial Downloader */ return BOOT_DEVICE_BOARD; /* * The above method does not detect that the boot ROM used * serial downloader in case the boot ROM decided to use the * serial downloader as a fall back (primary boot source failed). * * Infer that the boot ROM used the USB serial downloader by * checking whether the USB PHY is currently active... This * assumes that SPL did not (yet) initialize the USB PHY... */ if (is_boot_from_usb()) return BOOT_DEVICE_BOARD; #endif enum boot_device boot_device_spl = get_boot_device(); if (IS_ENABLED(CONFIG_IMX8MM) || IS_ENABLED(CONFIG_IMX8MN) || IS_ENABLED(CONFIG_IMX8MP)) return spl_board_boot_device(boot_device_spl); switch (boot_device_spl) { #if defined(CONFIG_MX7) case SD1_BOOT: case MMC1_BOOT: case SD2_BOOT: case MMC2_BOOT: case SD3_BOOT: case MMC3_BOOT: return BOOT_DEVICE_MMC1; #elif defined(CONFIG_IMX8) case MMC1_BOOT: return BOOT_DEVICE_MMC1; case SD2_BOOT: return BOOT_DEVICE_MMC2_2; case SD3_BOOT: return BOOT_DEVICE_MMC1; case FLEXSPI_BOOT: return BOOT_DEVICE_SPI; #elif defined(CONFIG_IMX8M) case SD1_BOOT: case MMC1_BOOT: return BOOT_DEVICE_MMC1; case SD2_BOOT: case MMC2_BOOT: return BOOT_DEVICE_MMC2; #endif case NAND_BOOT: return BOOT_DEVICE_NAND; case SPI_NOR_BOOT: return BOOT_DEVICE_SPI; case USB_BOOT: return BOOT_DEVICE_USB; default: return BOOT_DEVICE_NONE; } } #endif /* CONFIG_MX7 || CONFIG_IMX8M || CONFIG_IMX8 */ #ifdef CONFIG_SPL_USB_GADGET int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char *name) { put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM + 0xfff, &dev->idProduct); return 0; } #endif #if defined(CONFIG_SPL_MMC_SUPPORT) /* called from spl_mmc to see type of boot mode for storage (RAW or FAT) */ u32 spl_boot_mode(const u32 boot_device) { #if defined(CONFIG_MX7) || defined(CONFIG_IMX8M) || defined(CONFIG_IMX8) switch (get_boot_device()) { /* for MMC return either RAW or FAT mode */ case SD1_BOOT: case SD2_BOOT: case SD3_BOOT: #if defined(CONFIG_SPL_FAT_SUPPORT) return MMCSD_MODE_FS; #else return MMCSD_MODE_RAW; #endif break; case MMC1_BOOT: case MMC2_BOOT: case MMC3_BOOT: #if defined(CONFIG_SPL_FAT_SUPPORT) return MMCSD_MODE_FS; #elif defined(CONFIG_SUPPORT_EMMC_BOOT) return MMCSD_MODE_EMMCBOOT; #else return MMCSD_MODE_RAW; #endif break; default: puts("spl: ERROR: unsupported device\n"); hang(); } #else /* * When CONFIG_SPL_FORCE_MMC_BOOT is defined the 'boot_device' is used * unconditionally to decide about device to use for booting. * This is crucial for falcon boot mode, when board boots up (i.e. ROM * loads SPL) from slow SPI-NOR memory and afterwards the SPL's 'falcon' boot * mode is used to load Linux OS from eMMC partition. */ #ifdef CONFIG_SPL_FORCE_MMC_BOOT switch (boot_device) { #else switch (spl_boot_device()) { #endif /* for MMC return either RAW or FAT mode */ case BOOT_DEVICE_MMC1: case BOOT_DEVICE_MMC2: case BOOT_DEVICE_MMC2_2: #if defined(CONFIG_SPL_FS_FAT) return MMCSD_MODE_FS; #elif defined(CONFIG_SUPPORT_EMMC_BOOT) return MMCSD_MODE_EMMCBOOT; #else return MMCSD_MODE_RAW; #endif break; default: puts("spl: ERROR: unsupported device\n"); hang(); } #endif } #endif #if defined(CONFIG_IMX_HAB) /* * +------------+ 0x0 (DDR_UIMAGE_START) - * | Header | | * +------------+ 0x40 | * | | | * | | | * | | | * | | | * | Image Data | | * . | | * . | > Stuff to be authenticated ----+ * . | | | * | | | | * | | | | * +------------+ | | * | | | | * | Fill Data | | | * | | | | * +------------+ Align to ALIGN_SIZE | | * | IVT | | | * +------------+ + IVT_SIZE - | * | | | * | CSF DATA | <---------------------------------------------------------+ * | | * +------------+ * | | * | Fill Data | * | | * +------------+ + CSF_PAD_SIZE */ __weak void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image) { typedef void __noreturn (*image_entry_noargs_t)(void); uint32_t offset; image_entry_noargs_t image_entry = (image_entry_noargs_t)(unsigned long)spl_image->entry_point; debug("image entry point: 0x%lX\n", spl_image->entry_point); if (spl_image->flags & SPL_FIT_FOUND) { image_entry(); } else { /* * HAB looks for the CSF at the end of the authenticated * data therefore, we need to subtract the size of the * CSF from the actual filesize */ offset = spl_image->size - CONFIG_CSF_SIZE; if (!imx_hab_authenticate_image(spl_image->load_addr, offset + IVT_SIZE + CSF_PAD_SIZE, offset)) { image_entry(); } else { puts("spl: ERROR: image authentication fail\n"); hang(); } } } #if !defined(CONFIG_SPL_FIT_SIGNATURE) ulong board_spl_fit_size_align(ulong size) { /* * HAB authenticate_image requests the IVT offset is * aligned to 0x1000 */ size = ALIGN(size, 0x1000); size += CONFIG_CSF_SIZE; return size; } void board_spl_fit_post_load(ulong load_addr, size_t length) { u32 offset = length - CONFIG_CSF_SIZE; if (imx_hab_authenticate_image(load_addr, offset + IVT_SIZE + CSF_PAD_SIZE, offset)) { puts("spl: ERROR: image authentication unsuccessful\n"); hang(); } } #endif #endif #if defined(CONFIG_MX6) && defined(CONFIG_SPL_OS_BOOT) int dram_init_banksize(void) { gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; gd->bd->bi_dram[0].size = imx_ddr_size(); return 0; } #endif