When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.
This commit is taken from Linux:
'commit 0b14392db2e'
("mtd: nand: pxa3xx_nand: fix early spurious interrupt")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Since the pxa3xx_nand driver was added there has been a discrepancy in
pxa3xx_nand_set_sdr_timing() around the setting of tWP_min and tRP_min.
This brings us into line with the current Linux code.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Don't store struct mtd_info in struct pxa3xx_nand_host. Instead use the
one that is already part of struct nand_chip. This brings us in line
with current U-boot and Linux conventions.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).
ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
This commit is taken from Linux:
'commit c16340973fcb64614' ("nand: pxa3xx: Increase initial buffer size")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove smi_pins definition since it is already in armada-37xx.dtsi.
Add assigned-clocks definitions to spi0.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the pci-aardvark driver in defconfig for Turris Mox and also
enable the pci command.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The macro name CONFIG_WDT_ARMADA_3720 is called CONFIG_WDT_ARMADA_37XX
instead. Fix this so that watchdog really is enabled in board_init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for changing clock rate and parent clock for Armada 37xx
peripheral clocks.
Only clocks which can be disabled (.can_gate is true) can have parent
or rate changed.
This is needed so that Turris Mox can change SPI clock in device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.
This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.
This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The bootROM in the Armada-38x (and similar) SoC has two modes for UART
boot. The first is when the normal boot media is blank (or otherwise
missing the kwb header). The second is when the boot sequence has been
interrupted with the magic byte sequence on the UART lines.
In the first mode the bootROM routine and error code register will
indicate that there was an error booting from the configured media in
bits 7:0. In the second mode there is no error to indicate but the boot
source is provided via bits 31:28.
Handle both situations so that kwboot can be used for both boot
strapping a blank board and for intercepting a regular boot sequence.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
This reverts commit e83e2b3900. This
prevents kwboot from overriding the hardware strapped boot source.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Detect the SD/eMMC boot device at run-time. Load the environment from
the boot deice, as well as save to it.
Leave the environment offset the same as in the SPI flash.
Make SD/eMMC 0 the default environment device when the boot device is
not detected.
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch accomplishes 2 things to make the kwboot procedure
on the a38x more reliable.
1) We fill the tty with 1K of the magic bootparam. This helps
with the timing of where the microcode picks up in the read of
the line to ensure we actually catch the break to go into recovery
mode
2) Before starting the xmodem transfer we sleep for 2 seconds
and then flush the line. This allows all the magic bootparam
to be flushed from the line and makes the xmodem transfer reliable
and removes the Bad message failures.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan is listed as a kirkwood maintainer since commit f822d8578b
(MAINTAINERS: Update Marvell custodianship).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The default bootdelay of 3 seconds is good enough and there is no need
to duplicate it in CONFIG_EXTRA_ENV_SETTINGS.
Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The comment of child_pre_probe, one of the 'struct uclass_driver'
members, is currently missing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, "help dm" shows as follows:
=> help dm
dm - Driver model low level access
Usage:
dm tree Dump driver model tree ('*' = activated)
dm uclass Dump list of instances for each uclass
dm devres Dump list of device resources for each device
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This adds a new defconfig which pre-selects the PICO-Hobbit baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds a new defconfig which pre-selects the PICO-Pi baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This fixes four small typos in the README file.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds ofnode_by_prop_value() to search for nodes with a given property
and value, an ofnode version of fdt_node_offset_by_prop_value().
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit 30a90f56c3 ("dm: core: add functions to get memory-mapped I/O
addresses") introduced a devfdt_remap_addr_index() routine but it does
not make use of the index parameter.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
All Linux firmware drivers are put under "/firmware" node
and it has support to populate "/firmware" node by default.
u-boot and Linux can share same DTB. In this case, driver
probe for devices under "/firmware" will not be invoked
as "/firmware" does not have its own "compatible" property.
This patch scans "/firmware" node by default like "/clocks".
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create separate function for scanning node by path and
move "/clock" node scan code into that function.
This will be usable if scanning of more node is required.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a driver to configure the SerDes (Serializer/Deserializer) lanes on
the MPC83xx architecture.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
When the DM CPU drivers are active, printing information about a CPU
should be delegated to a matching driver.
Hence, add a static print_cpuinfo that implements this delegation when
DM CPU drivers are active.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Changed condition to CONFIG_IS_ENABLED(CPU):
Signed-off-by: Simon Glass <sjg@chromium.org>
To print the reset status during boot, add a method print_resetinfo to
board_f, which is called in init_sequence_f[], that gets the reset
information from the sysreset driver (assuming there is only one seems
reasonable), and prints it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
It's useful to have the reset status of the SoC printed out during reset
(e.g. to learn whether the reset was caused by software or a watchdog).
As a first step to implement this, add a get_status method to the
sysreset class, which enables the caller to get printable information
about the reset status (akin to get_desc in the CPU uclass).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
