Writing "0x00" to the USBOTGSS_IRQENABLE_SET_MISC and
USBOTGSS_IRQENABLE_SET_0 doesn't disable the interrupts. Used
USBOTGSS_IRQENABLE_CLR_MISC and USBOTGSS_IRQENABLE_CLR_0 instead.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer
alignment into account which led to failures of the following form:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
[trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The device might have already been probed during the call to
device_probe() on its parent device (e.g. PCI bridge devices).
In its parent device's probe routine, it might probe all of
its child devices via device_probe() thus the codes reenter
device_probe_child(). To support code reentrancy, test these
allocated memory against NULL to avoid memory leak, and return
to the caller if dev->flags has DM_FLAG_ACTIVATED set after
device_probe() returns, so that we don't mess up the device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
If there is no pci device listed in the device tree,
don't bother scanning the device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far if CONFIG_VGA_AS_SINGLE_DEVICE is not defined, the VGA device
will try to initialize a keyboard device (for x86, it is i8042). But
if i8042 controller initialization fails (eg: there is no keyboard
connected to the PS/2 port), drv_video_init() just simply returns.
This kills the opportunity of using a usb keyboard later with the vga
console, as the vga initialization part is actually ok, only keyboard
part fails. Change the code logic to allow this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The existing i8042 keyboard controller driver has some issues.
First of all, it does not issue a self-test command (0xaa) to the
controller at the very beginning. Without this, the controller
does not respond to any command at all. Secondly, it initializes
the configuration byte register to turn on the keyboard's interrupt,
as U-Boot does not normally allow interrupts to be processed.
Finally, at the end of the initialization routine, it wrongly
sets the controller to disable all interfaces including both
keyboard and mouse.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
- Rename CamelCase variables to conform U-Boot coding convention
- Rename wait_until_kbd_output_full() to kbd_output_full()
- Change to use macros for i8042 command and control register bits
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reorder those static function so that their declarations
can be removed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This function can return an error. Correct the detection of this error so
that it works even with large 32-bit addresses.
The return value is set up for returning an I/O address but the function is
also used to return a memory-mapped address. Adjust the return code to make
this work.
Also add a bit more debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
These calls seem to be incorrect. The function expects an I/O address but
the existing callers pass the value at an I/O address. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
In pci_uclass_child_post_bind(), bdf is extracted from fdt_pci_addr.
Mask bus number before save it to pplat->devfn.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add an api to enable and configure the integrated keyboard controller
on SMSC LPC47m superio chipset. It also adds several macros to help
future extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Per Intel FSP specification, we should call FSP notify API to
inform FSP that PCI enumeration has been done so that FSP will
do any necessary initialization as required by the chipset's
BIOS Writer's Guide (BWG).
Unfortunately we have to put this call here as with driver model,
the enumeration is all done on a lazy basis as needed, so until
something is touched on PCI it won't happen.
Note we only call this after U-Boot is relocated and root bus has
finished probing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On some platforms pci devices behind bridge need to be probed (eg:
a pci uart on recent x86 chipset) before relocation. But we won't
bind all devices found during the enumeration. Only devices whose
driver with DM_FLAG_PRE_RELOC set will be bound. Any other generic
devices except bridges won't be bound.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currenlty we only set up video framebuffer when VIDEO_VESA driver is
used. With coreboot, VIDEO_COREBOOT driver is used instead. Since we
already saved VESA mode in the VIDEO_COREBOOT driver, now we can also
set up video framebuffer for coreboot before loading Linux kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When booting as a coreboot payload, the framebuffer details are
passed from coreboot via configuration tables. We save these
information into vesa_mode_info structure for future use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
commit 6497e37 "net: e1000: Support 64-bit physical address" causes
compiler warnings on 32-bit U-Boot build below.
drivers/net/e1000.c: In function 'e1000_configure_tx':
drivers/net/e1000.c:4982:2: warning: right shift count >= width of type [enabled by default]
drivers/net/e1000.c: In function 'e1000_configure_rx':
drivers/net/e1000.c:5126:2: warning: right shift count >= width of type [enabled by default]
This commit fixes the build warnings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Follow linux dma flow:
Before DMA read, be sure to invalidate the cache over the address
range of DMA buffer to prevent cache coherency problems.
After DMA read, invalidate dcache again.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.
The following graph is modified from kernel gpmi-nand.c driver with
each data block 512 bytes. We can see that Block Mark conflicts with
ecc area from bch view. We can enlarge the ecc chunk size to avoid
this problem to those oobsize which is larger than 512.
| P |
|<----------------------------------------------------------------->|
| |
| (Block Mark) |
| P' | | | |
|<--------------------------------------------------->| D | | O'|
| |<--------->| |<->|
V V V V V
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
| M | data |E| data |E| data |E| data |E| |
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
^ ^
| O |
|<---------------->|
P : the page size for BCH module.
E : The ECC strength.
G : the length of Galois Field.
N : The chunk count of per page.
M : the metasize of per page.
C : the ecc chunk size, aka the "data" above.
P': the nand chip's page size.
O : the nand chip's oob size.
O': the free oob.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Cloned from the Linux driver v4.2.0-rc2. Plus some patches from
Antoine Tenart enabling controller initialization and ONFI timing
support:
http://lists.infradead.org/pipermail/linux-mtd/2015-July/060197.html
Please note that this driver needs the Linux NAND subsystem sync to v4.1
from Scott to be applied:
https://www.mail-archive.com/u-boot@lists.denx.de/msg175762.html
Otherwise it will not compile.
Tested on the Marvell Armada XP DB-MV784MP-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Ezeguil Garcia <ezequiel.garcia@free-electrons.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
Update the NAND code to match Linux v4.1. The previous sync was
from Linux v3.15 in commit 4e67c57125.
CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout. Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[scottwood: Cherry-picked from Linux 8471bb73ba10ed67]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Conflicts:
configs/socfpga_arria5_defconfig
configs/socfpga_cyclone5_defconfig
configs/socfpga_socrates_defconfig
Merged these by hand and re-ran savedefconfig on them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add driver for the DesignWare APB GPIO IP block.
This driver is DM capable and probes from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Fix the following problem:
drivers/ddr/altera/sequencer.c: In function 'sdram_calibration_full':
drivers/ddr/altera/sequencer.c:1943:25: warning: 'found_failing_read' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (found_passing_read && found_failing_read)
^
drivers/ddr/altera/sequencer.c:1803:26: note: 'found_failing_read' was declared here
u32 found_passing_read, found_failing_read, initial_failing_dtap;
^
Signed-off-by: Marek Vasut <marex@denx.de>
This gem is really really rare, there was an actual float used in
the Altera DDR init code, which pulled in floating point ops from
the libgcc, just wow.
Since we don't support floating point operations the same way Linux
does not support them, replace this with an integer multiplication
and division combo. This removes some 2kiB of size from the SPL as
the floating point ops are no longer pulled in from libgcc.
This was detected by enabling CONFIG_USE_PRIVATE_LIBGCC=y , which
does not contain the floating point bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Add Kconfig options in preparation for moving boards to use Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update this driver to support driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
Since struct eth_device does not exist with CONFIG_DM_ETH defined, avoid
using it in the driver unless necessary. Most of the time it is better to
pass the private driver pointer anyway.
Also refactor the code so that code that the driver model implementation
will share are available in functions that can be called. Add stubs where
necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
We cannot currently include any header files in the C files since common.h
needs to be included first, and it is in the header file. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
High 32-bit address is needed when u-boot runs in 64-bit space.
Tested on armv8-based LS2085ARDB.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This driver is not used only on exynos, but also on Altera SoCFPGA,
HiSilicon SoCs, RPi etc, so rename it accordingly to prevent confusion.
Signed-off-by: Marek Vasut <marex@denx.de>
populate _reset_ callback to the USB ethernet gadget since UDC core
expects every gadget driver to have the reset callback. This shouldn't
be needed once the ethernet gadget driver is adapted to use the
composite driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
xhci omap driver has board_usb_init in xhci_hcd_init but doesn't have
the corresponding cleanup function in xhci_hcd_stop.
Fix it here by invoking board_usb_cleanup() in xhci_hcd_stop().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Ethernet gadget driver can be used both by both SPL and u-boot. Since
usb_eth_init() is the entry point for ethernet gadget driver, perform
board initialization there. Also perform the cleanup in usb_eth_halt.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
This patch fixes a potential NULL pointer dereference arising on
non-present/non-initialized xHCI controllers and adds some error
handling to xHCI code
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
USB EHCI on SPEAr600 has not been tested for a while. The base controller
addresses are missing. This patch adds the defines to the header. And adds
the missing code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Document target board specific functions
board_ehci_hcd_init - override usb phy mode
board_ehci_hcd_init - set usb vbus voltage
board_ehci_power - enables/disables usb vbus voltage
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
We do not want to compile the DM remove code for SPL. Currently,
we undef it in include/config_uncmd_spl.h (for C files) and in
scripts/Makefile.uncmd_spl (for Makefiles). This is really ugly.
This commit demonstrates how we can deprecate those two files.
Use $(SPL_) for the entry in the Makfile and CONFIG_IS_ENABLED()
in C files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Just preparing for upcoming cleaning.
The board-specific linker script board/vpac270/u-boot-spl.lds
has been touched to avoid build error. It does not change the
size of spl/u-boot-spl.bin for this board, so it should be OK.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
LPC32xx has 3 I2C bus controllers, 2 of them are used as generic ones
and their parent clock is HCLK and CLK_HI/CLK_LO registers are 10 bit
wide. This means that if HCLK is 104MHz, then minimal configurable I2C
clock speed is about 51KHz.
Only USB OTG I2C bus controller CLK registers are 8 bit wide, thus in
assumption that peripheral clock is 13MHz it allows to set the minimal
bus speed about 25.5KHz.
Check for negative half clock value is removed since it is always false.
The change fixes the following problem for I2C busses 0 and 1:
=> i2c dev 0
Setting bus to 0
=> i2c speed 100000
Setting bus speed to 100000 Hz
Failure changing bus speed (-22)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Updated the LPC32xx I2C driver to support
the OTG I2C that is part of the USB module.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (ECC layout for small page)
This layout is matching the lpc32xx NAND SLC Linux Kernel driver.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate NAND SLC hardware ECC support from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (hardware ECC support)
- lpc3250 header file missing SLC NAND registers definition
The legacy driver was updated and clean-up as part of the integration with the existing NAND SLC driver.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Incorporate DMA driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx DMA driver
- lpc3250 header file DMA registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
ti_qspi uses memory map mode for faster read. Enabling DMA will increase
read speed by 3x @48MHz on DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Update op_mode_rx flag based on CONFIG_QSPI_QUAD_SUPPORT flag,
instead of platform.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This adds a PCI driver for the controllers found on Marvell MVEBU SoCs.
Besides the driver, this patch also removes the statically defined
PCI MBUS windows. As they are not needed anymore, since this PCIe
driver now creates the windows dynamically.
Tested on Armada XP db-mv784mp-gp eval board using an Intel E1000
PCIe card in all 3 PCIe slots. And on the Armada 38x db-88f6820-gp
eval board using this Intel E1000 PCIe card in the PCIe 0 slot.
This port was done in cooperation with Anton Schubert.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
This patch introduces the SDRAM scrubbing for ECC enabled board
to fill/initialize the ECC bytes. This is done via the XOR engine
to speed up the process. The scrubbing is a 2-stage process:
1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot
2) U-Boot scrubs the remaining SDRAM area(s)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for multiple hostcontrollers to the ehci-marvell driver
and enables all 3 usb-hcs on the db-mv784mp-gp board.
It depends on the initial Armada XP usb support patch from Stefan.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enables the USB EHCI support for the Marvell Armada XP (AXP)
SoCs. In compatism to the Armada 38x (A38x), the AXP needs to configure
the USB PLL and the USB PHY's specifically in U-Boot. The A38x has done
this already in the bin_hdr (SPL U-Boot). Without this, accessing the
controller registers in U-Boot or Linux will hang the CPU.
Additionally, the AXP uses a different USB EHCI base address. This
patch also takes care of this by runtime SoC detection in the Marvell
EHCI driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enables the NAND controller on the Armada XP/38x and provides
a new function that returns the NAND controller input clock. This
function will be used by the MVEBU NAND driver.
As part of this patch, the multiple BIT macro definitions are moved
to a common place in soc.h.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is tested on the DB-MV784MP-GP eval board. To really enable ECC
support on this board the I2C EEPROM needs to get changed. As it
saves the enabling of ECC support internally. For this the following
commands can be used to enable ECC support on this board:
Its recommended for first save (print) the value(s) in this EEPROM
address:
=> i2c md 4e 0.1 2
0000: 05 00 ..
To enable ECC support you need to set bit 1 in the 2nd byte:
Marvell>> i2c mw 4e 1.1 02
Marvell>> i2c md 4e 0.1 2
0000: 05 02 ..
To disable ECC support again, please use this command:
Marvell>> i2c mw 4e 1.1 00
Marvell>> i2c md 4e 0.1 2
0000: 05 00 ..
On other AXP boards, simply plugging an ECC DIMM should be enough to
enable ECC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Fix a condition that generate watchdog timeout inside "lpc32xx_i2c_write" when parameters alen = 0 and len = 0.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Fix a condition that generate watchdog timeout inside "lpc32xx_i2c_read" when parameters alen != 0 and len = 0.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
The HCLK is not constant and can take different value; use the api function to get the value of the HCLK for the I2C clock high and low computation.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Make the support for 4K subpage I/O on a SPI NOR flash configurable.
A board which requires the SPI NOR to be accessed in larger 32KiB
or 64KiB pages can disable the 4K subpage support, but by default,
the support for 4K subpage I/O is enabled. The functionality of this
option is the same as CONFIG_MTD_SPI_NOR_USE_4K_SECTORS in Linux.
This is extremely useful in case one uses UBI on a SPI NOR flash.
UBI needs at least 15k EBs and can not work on a flash which uses
4k ones, so disabling the support for 4k subpages lets UBI work on
such flash.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow
reuse of existing code for ARMv8 based Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This reverts commit df189d9ba3.
Unfortunately this commit breaks chromebook_link because it adds lots of PCI devices
before relocation and there is not enough pre-reloc malloc() memory.
Rathar then increase this memory, revert for now until we figure this out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This part of mentioned commit, was missed by my mistake during the rebase.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Original commit message:
power: pmic: pfuze100 support driver model
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Change-Id: I4fc88414f3c0285f9648e47ec7aed60addeccc4d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
These functions allow iteration through all PCI devices including bridges.
The children of each PCI bus are returned in turn. This can be useful for
configuring, checking or enumerating all the devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present there are no PCI functions which allow access to PCI
configuration using a struct udevice. This is a sad situation for driver
model as it makes use of PCI harder. Add these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.
While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the ANX9804 bridge chip, which can take pixel data coming
from a parallel LCD interface and translate it on the fly into a DP
interface for driving eDP TFT displays. It uses I2C for configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add support for using the mipi pll as lcd clock source, this is
necessary for getting higher dotclocks with lcd panels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
sun6i and later have a couple of io-blocks which are shared between the
main CPU core and the "R" cpu which is small embedded cpu which can be
active while the main system is suspended.
These gpio banks sit at a different mmio address then the normal banks,
and have a separate devicetree node and compatible, this adds support for
these banks to the sunxi-gpio code when built with device-model support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The tv-encoder on sun5i is slightly different compared to the one on
sun4i/sun7i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for making the visual area of the framebuffer smaller and
drawing a black border around it. This is intended for use with
overscanning monitors (esp. with composite video out), to avoid part
of the picture being invisible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
cfbconsole currently assumes that the width and stride of the framebuffer
are the same, in most places where stride matters it uses a VIDEO_LINE_LEN
helper macro.
This commit changes the few places not using VIDEO_LINE_LEN to also use
VIDEO_LINE_LEN, and protects the default VIDEO_LINE_LEN with a #ifndef
guard, allowing the boards config.h to override and, and thus support
cases where stride != width.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
The passed in width is always VIDEO_COLS. This is a preparation patch
for adding stride != width support to the cfbconsole code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Disable subpage writes as we do not provide ecc->hwctl.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
