i2c changes for v2020.10
- Add support for I2C controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
- Add I2C controller support for Cortina Access CAxxxx SoCs
- new rtc methods, rtc command, and tests
- imx_lpi2c: Improve the codes to use private data
- stm32f7_i2c.c: Add new compatible "st,stm32mp15-i2c"
- stm32f7_i2c.c: Add Fast Mode Plus support
- pwm: Add PWM driver for SiFive SoC
Since the mdio code got upstreamed it is not possible
to activate network ports on CP110 Master and Slave.
The problem is in mvpp2_base_probe which is called for each
CP110 and it initializes the buffer area for descs and rx_buffers.
This should only happen once though and the bd space is actually
set to 0 after the first run of the function.
This leads to an error when the second CP110 tries the initialization
again and disables all network ports on this CP110.
This patch adds a static variable to check if the buffer area is
initialized only once globally.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Measurements on actual hardware shown that the read ODT is early by 3
clocks. Adjust the calculation to avoid this.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[upstream https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/22]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
In the Armada 385 functional spec (MV-S109094-00 Rev. C) the read sample
delay fields are 5 bits wide. Use the correct bitmask of 0x1f when
extracting the value.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[upstream https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/22]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Adds a PWM driver for PWM chip present in SiFive's HiFive Unleashed SoC
This driver is simple port of Linux pwm sifive driver from Linux v5.6
commit: 9e37a53eb051 ("pwm: sifive: Add a driver for SiFive SoC PWM")
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Read SYSCFG bindings to set Fast Mode Plus bits if Fast Mode Plus
speed is selected.
Handle the stm32mp15 specific compatible to handle FastMode+
registers handling which is different on the stm32mp15 compared
to the stm32f7 or stm32h7.
Indeed, on the stm32mp15, the FastMode+ set and clear registers
are separated while on the other platforms (F7 or H7) the control
is done in a unique register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a new compatible "st,stm32mp15-i2c" introduced in Linux kernel v5.8
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
It's more natural that any write that happens to touch the reset
register should cause a reset, rather than just a write that starts at
that offset.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The current set method is broken; a simple test case is to first set
the date to something in April, then change the date to 31st May:
=> date 040412122020.34
Date: 2020-04-04 (Saturday) Time: 12:12:34
=> date 053112122020.34
Date: 2020-05-01 (Friday) Time: 12:12:34
or via the amending of the existing rtc_set_get test case similarly:
$ ./u-boot -T -v
=> ut dm rtc_set_get
Test: dm_test_rtc_set_get: rtc.c
expected: 31/08/2004 18:18:00
actual: 01/08/2004 18:18:00
The problem is that after each register write,
sandbox_i2c_rtc_complete_write() gets called and sets the internal
time from the current set of registers. However, when we get to
writing 31 to mday, the registers are in an inconsistent state (mon is
still 4), so the mktime machinery ends up translating April 31st to
May 1st. Upon the next register write, the registers are populated by
sandbox_i2c_rtc_prepare_read(), so the 31 we just wrote to mday gets
overwritten by a 1.
Fix it by writing all registers at once, and for consistency, update
the get method to retrieve them all with one "i2c transfer".
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This simply consists of renaming the existing pcf2127_read_reg()
helper to follow the naming of the other
methods (i.e. pcf2127_rtc_<method name>) and changing the type of its
"len" parameter.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Similar to how the dm_rtc_{read,write} functions fall back to using
the {read,write}8 methods, do the opposite in the rtc_{read,write}8
functions.
This way, each driver only needs to provide either ->read8 or ->read
to make both rtc_read8() and dm_rtc_read() work - without this, a
driver that provides ->read() would most likely just duplicate the
logic here for implementing a ->read8() method in term of its ->read()
method. The same remarks of course apply to the write case.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Similar to dm_rtc_read(), introduce a helper that allows the caller to
write multiple consecutive 8-bit registers with one call. If the
driver provides the ->write method, use that, otherwise loop using
->write8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Some users may want to read multiple consecutive 8-bit
registers. Instead of each caller having to implement the loop,
provide a dm_rtc_read() helper. Also, allow a driver to provide a
->read method, which can be more efficient than reading one register
at a time.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Current driver calls the devfdt_get_addr to get the base address
of lpi2c controller in each sub-functions. Since the devfdt_get_addr
accesses the DTB and translate the address, it introduces much
overhead.
Improve the codes to use private variable which has recorded the
base address from probe.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The offset at which the image to be loaded from NAND is located is
retrieved from the itb header. The presence of bad blocks in the area
of the NAND where the itb image is located could invalidate the offset
which must therefore be adjusted taking into account the state of the
sectors concerned.
cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
tpm_tis_spi.c directly includes tpm_tis.h and tpm-v2.h which both
define the same enums (see e.g. TPM_ACCESS_VALID). Add an #ifndef to
prevent redeclaration errors.
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
This solves a compatibility issue with Linux device trees
that contain TPMv2.x hardware. So it's easier to import DTS
from upstream kernel when migrating board init from C code
to DTS.
The issue is that fallback binding is different between Linux
and u-Boot.
Linux: "tcg,tpm_tis-spi"
U-Boot: "tis,tpm2-spi"
As there are currently no in-tree users of the U-Boot binding,
it makes sense to use Linux fallback binding.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Even though the sata_sil driver was converted over to the driver model,
it still assumed that the PCI controller is using the legacy interface.
Allow the "devno" member to be a struct udevice pointer and use
DM_PCI_COMPAT to covert the rest of the interface.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When compiled as a DM_ETH driver, the scm911x driver was reading the MAC
address from the optional EEPROM storage, but failed to copy this to the
platdata struct. Since it was also missing a definition of the
read_rom_hwaddr() function, the generic Ethernet code was dismissing
this MAC address, falling back to a random address or denying to start
at all.
Add an implementation of .read_rom_hwaddr, and refactor the function
reading the ROM address to be called by all interested parties.
This fixes MAC address issues when using the driver in DM_ETH "mode".
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
dm_gpio_lookup_name() searches for a gpio through
the bank name. But we have also gpio labels, and it
makes sense to search for a gpio also in the labels
we have defined, if no gpio is found through the
bank name definition.
This is useful for example if you have a wp pin on
different gpios on different board versions.
If dm_gpio_lookup_name() searches also for the gpio labels,
you can give the gpio an unique label name and search
for this label, and do not need to differ between
board revisions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Don't enable by default]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patchs adds glue logic to enable designware mac present on
Action Semi based S700 SoC, Configures SoC specific bits.
Undocumented bit that programs the PHY interface select register
comes from vendor source.
It has been tested on Cubieboard7-lite based on S700 SoC.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.
This commits lets proper packets to be transmitted over the network.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds support for Realtek PHY RTL8201F 10/100Mbs
(with variants: RTL8201FN and RTL8201FL) PHYceiver. It is
present on Actions Semi Cubieboard7 board.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This commit adds clocks needed for ethernet operations for
Actions OWL family of SoCs (S700 and S900).
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Renamed dm "drivers" subcommand to "compat" (as it listed
compatibility strings) and prevent it from segfaulting when
drivers have no of_match populated.
Added a new "drivers" subcommand to dump a list of all known DM
drivers and for each, their uclass id, uclass driver and names of
attached devices.
Added a new "static" subcommand to dump a list of DM drivers with
statically defined platform data.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add size and addr parameter to test "All" to override the default
value (4kB and STM32_DDR_BASE) used in tests with these optional
parameters: [size] or [addr].
When other optional parameters are present before [addr],
they are replaced by default value:
- [loop] = "1"
- [pattern] = "-" (new: force default pattern)
Example to use:
DDR>test 0 1 0x20000
DDR>test 0 1 0x1000000 0xD0000000
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The test 4 = "AddressBus [size] [addr]" without parameter
detects alias for any address bit only when:
- size = real size of DDR
- addr = start of DDR = 0xC0000000
These value must be the default value when parameters are absent.
This patch sets bufsize to STM32_DDR_SIZE and get_bufsize() selects
the correct value for bufsize when this parameter is absent =
full size of the DDDR
On EV1 board :
DDR> test 4
running at 0xC0000000 length 0x40000000
On DK2 board
DDR> test 4
running at 0xC0000000 length 0x20000000
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a parameter addr in test FrequencySelectivePattern to select
the base address used to execute the tests.
Default value (when the parameter is absent) is STM32_DDR_BASE,
selected in get_addr() function.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add protection on minimum value for result of get_bufsize
and check the alignment of buffer size: only multiple min_size
is allowed; only 4 bytes alignment was checked previously
(value & 0x3).
For example the "Random" test raises an issue when size is not 8 bytes
aligned because address for buffer = address + size / 2 is not word
aligned.
This patch avoid test error for unsupported size value.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
There maybe an overshoot:
- when disabling, then re-enabling vrefbuf too quickly
- or upon platform reset as external capacitor maybe slow
discharging (VREFBUF is HiZ at reset by default).
VREFBUF is used by ADC/DAC on some boards. An overshoot on the reference
voltage make the conversions inaccurate for a short period of time. So:
- Don't put the VREFBUF in HiZ when disabling, to force an active
discharge.
- Enforce a 1ms OFF/ON delay, also upon reset
Penalty is a 1ms delay is applied (even for a cold boot), when enabling
VREFBUF.
Fixes: 93cf0ae775 ("power: regulator: Add support for stm32-vrefbuf")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add information on pin configuration used for pinmux command:
- bias configuration for output (disable, pull up, pull down)
- otype for input (open drain or push pull)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add information on pin configuration used for pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of ops get_dir_flags() to read dir flags from
STMFX registers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the helper functions stmfx_read_reg() and stmfx_write_reg() to avoid
duplicated code for access to stmfx's register with mask.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Rename the two function used to change the pin configuration
from stmfx_pinctrl_.. stmfx_conf_... to clarify the function usage.
No functional change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the functions stmfx_pinctrl_set_pupd and stmfx_pinctrl_set_type;
they can be used by the new ops get_dir_flags and set_dir_flags introduced
by next patch.
No functional change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add ops get_dir_flags() to read dir flags from GPIO registers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a weak functions to save the vddcore voltage value provided
in the OPP node when the clock tree is initialized.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The PLL1 node (st,pll1) is optional in device tree, the max supported
frequency define in OPP node is used when the node is absent.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update the compatible associated with the STM32 MPU glue
in the DWC ethernet driver.
The supported compatible is the specific "st,stm32mp1-dwmac"
as indicated in Linux binding
Documentation/devicetree/bindings/net/stm32-dwmac.txt
and not the "snps,dwmac-4.20a" only used to the select IP
version.
This glue is implemented in Linux kernel in:
drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
For information in stm32mp151.dtsi, the 2 compatibles are
supported:
ethernet0: ethernet@5800a000 {
compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch restores CONFIG_VIDCONSOLE_AS_LCD as boolean
and introduce a separate sting as CONFIG_VIDCONSOLE_AS_NAME
to search this string in stdout used as videoconsole.
This patch avoid issue with board defconfig or code expecting
CONFIG_VIDCONSOLE_AS_LCD as boolean.
Fixes: 22b897a123 ("video: extend stdout video console work-around for 'vga'")
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Resync Kconfiglib with the v14.1.0 release.
- Re-sync our <linux/compiler*h> files with v5.7-rc5 from upstream.
- Fully resync checkpatch.pl with v5.7 release.
To safely to all of the above, we have a few bugfixes about functions
that need a 'static inline' but weren't. We also stop setting
CROSS_COMPILE in arch/*/config.mk. Finally, with the above changes
boards can now opt-in to optimizing inlining and we do this for the
socfpga stratix10 platform for space savings.
save the GPIOD_ flags also in the gpio descriptor.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fixes: 788ea83412 ("gpio: add function _dm_gpio_set_dir_flags")
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Walter Lozano <walter.lozano@collabora.com>
