Commit Graph

494 Commits

Author SHA1 Message Date
David A. Long
a28afca57d Add uboot "fdt_high" enviroment variable
Add a new "fdt_high" enviroment variable. This can be used to control (or prevent) the
relocation of the flattened device tree on boot. It can be used to prevent relocation
of the fdt into highmem.  The variable behaves similarly to the existing "initrd_high"
variable.

Signed-off-by: David A. Long <dave.long@linaro.org>
2011-07-16 11:58:30 -04:00
Yoshihiro Shimoda
afb35666da mmc: sh_mmcif: add support for Renesas MMCIF
Some Renesas SuperH have MMCIF module. This driver supports it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-07-15 20:29:21 -05:00
York Sun
1b3e3c4f26 powerpc/mpc8xxx: Enable calculation for fixed DDR chips
We used to have fixed parameters for soldered DDR chips. This patch
introduces CONFIG_SYS_DDR_RAW_TIMING to enable calculation based on timing
data from DDR chip datasheet, implemneted in board-specific files or header
files.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
Aneesh V
93bc21930a armv7: add PL310 support to u-boot
PL310 is the L2$ controller from ARM used in many SoCs
including the Cortex-A9 based OMAP4430

Add support for some of the key PL310 operations
	- Invalidate all
	- Invalidate range
	- Flush(clean & invalidate) all
	- Flush range

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-04 10:55:25 +02:00
Aneesh V
2c451f7831 armv7: cache maintenance operations for armv7
- Add a framework for layered cache maintenance
	- separate out SOC specific outer cache maintenance from
	  maintenance of caches known to CPU

- Add generic ARMv7 cache maintenance operations that affect all
  caches known to ARMv7 CPUs. For instance in Cortex-A8 these
  opertions will affect both L1 and L2 caches. In Cortex-A9
  these will affect only L1 cache

- D-cache operations supported:
	- Invalidate entire D-cache
	- Invalidate D-cache range
	- Flush(clean & invalidate) entire D-cache
	- Flush D-cache range
- I-cache operations supported:
	- Invalidate entire I-cache

- Add maintenance functions for TLB, branch predictor array etc.

- Enable -march=armv7-a so that armv7 assembly instructions can be
  used

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-04 10:55:25 +02:00
Alex Waterman
eced4626e4 NAND: Add 16bit NAND support for the NDFC
This patch adds support for 16 bit NAND devices attached to the
NDFC on ppc4xx processors. Two config entries were added:

  CONFIG_SYS_NDFC_16        - Setting this tells the NDFC that a
			      16 bit device is attached.
  CONFIG_SYS_NDFC_EBC0_CFG  - This is for the External Bus
			      Controller configuration register.

Also, a new ndfc_read_byte() function was added which does not
first convert the data to little endian.

The NAND SPL was also modified to do 16bit bad block testing
when a 16 bit chip is being used.

Signed-off-by: Alex Waterman <awaterman@dawning.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-07-01 15:56:52 -05:00
Wolfgang Denk
566e5cf451 ARM: drop unsupported 'trab' board
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it.  Drop it.

This includes support for VFD displays which have always been used by
this board only.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-22 20:00:51 +02:00
Kumar Gala
8f29084a4f powerpc/fsl_pci: Fix device tree fixups for newer platforms
We assumed that only a small set of compatiable strings would be needed
to find the PCIe device tree nodes to be fixed up.  However on newer
platforms the simple rules no longer work.  We need to allow specifying
the PCIe compatiable string for each individual SoC.

We introduce CONFIG_SYS_FSL_PCIE_COMPAT for this purpose and set it if
the default isn't sufficient.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-05-20 00:48:41 -05:00
Luca Ceresoli
7a83af07ae TFTP: add tftpsrv command
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-05-19 21:38:32 +02:00
Detlev Zundel
6abe6fb68b README: Clarify difference of CONFIG_WATCHDOG and CONFIG_HW_WATCHDOG
Now that we have the documentation, the code should be changed to reflect
it ;)

Asd far as I can see, these are the places where HW_WATCHDOG is used
instead of WATCHDOG:

arch/blackfin/cpu/blackfin/watchdog.c
arch/m68k/cpu/mcf547x_8x/cpu.c

The relevant maintainers are on CC.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
2011-05-12 23:26:07 +02:00
Luca Ceresoli
8eccee7ae7 README: remove spurious line
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-05-12 19:37:10 +02:00
John Rigby
910f1ae3eb Serial: p1011: new vendor init options
Two new options:

CONFIG_PL011_SERIAL_RLCR

Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
have separate receive and transmit line control registers.  Set
this variable to initialize the extra register.

CONFIG_PL011_SERIAL_FLUSH_ON_INIT

On some platforms (e.g. U8500) U-Boot is loaded by a second stage
boot loader that has already initialized the UART.  Define this
variable to flush the UART at init time.
empty fifo on init

Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
2011-05-12 19:09:07 +02:00
Wolfgang Denk
aeabdeb7a3 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2011-04-30 22:45:55 +02:00
Macpaul Lin
0abddf82d5 cmd_ide: enhance new feature "CONFIG_IDE_AHB"
Although most IDE controller is designed to be connected to PCI bridge,
there are still some IDE controller support AHB interface for SoC design.

The driver implementation of these IDE-AHB controllers differ from other
IDE-PCI controller, some additional registers and commands access is required
during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" in cmd_ide.c is
required to be defined to support these kinds of SoC controllers. Such as
Faraday's FTIDE020 series and Global Unichip's UINF-0301.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-04-30 21:04:25 +02:00
Kumar Gala
66412c6371 powerpc/85xx: Change timebase divisor to be defined per processor
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because
different SoCs have different divisor amounts.  All the PQ3 parts are
/8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:24 -05:00
Timur Tabi
ba8e76bd49 powerpc: use 'video-mode' environment variable to configure DIU
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration.  Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.

The old definition of the "monitor" environment variable only determines
which video port to use for output.  This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port.  The
resolution was hard-coded into board-specific code.  The Linux command-line
arguments needed to be hard-coded to the proper video definition string.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-04-28 21:31:16 +02:00
Kim Phillips
a000b7950d common: add a grepenv command
u-boot environments, esp. when boards are shared across multiple
users, can get pretty large and time consuming to visually parse.
The grepenv command this patch adds can be used in lieu of printenv
to facilitate searching.  grepenv works like printenv but limits
its output only to environment strings (variable name and value
pairs) that match the user specified substring.

the following examples are on a board with a 5313 byte environment
that spans multiple screen pages:

Example 1:  summarize ethernet configuration:

=> grepenv eth TSEC
etact=FM1@DTSEC2
eth=FM1@DTSEC4
ethact=FM1@DTSEC2
eth1addr=00:E0:0C:00:8b:01
eth2addr=00:E0:0C:00:8b:02
eth3addr=00:E0:0C:00:8b:03
eth4addr=00:E0:0C:00:8b:04
eth5addr=00:E0:0C:00:8b:05
eth6addr=00:E0:0C:00:8b:06
eth7addr=00:E0:0C:00:8b:07
eth8addr=00:E0:0C:00:8b:08
eth9addr=00:E0:0C:00:8b:09
ethaddr=00:E0:0C:00:8b:00
netdev=eth0
uprcw=setenv ethact $eth;setenv filename p4080ds/R_PPSXX_0xe/rcw_0xe_2sgmii_rev2_high.bin;setenv start 0xe8000000;protect off all;run upimage;protect on all
upuboot=setenv ethact $eth;setenv filename u-boot.bin;setenv start eff80000;protect off all;run upimage;protect on all
upucode=setenv ethact $eth;setenv filename fsl_fman_ucode_P4080_101_6.bin;setenv start 0xef000000;protect off all;run upimage;protect on all
usdboot=setenv ethact $eth;tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/initramfs.cpio.gz.uboot;tftp c00000 $dir/p4080ds-usdpaa.dtb;setenv bootargs root=/dev/ram rw console=ttyS0,115200 $othbootargs;bootm 1000000 2000000 c00000;
=>

Example 2: detect unused env vars:

=> grepenv etact
etact=FM1@DTSEC2
=>

Example 3: reveal hardcoded variables; e.g., for fdtaddr:

=> grepenv fdtaddr
fdtaddr=c00000
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
=> grep $fdtaddr
fdtaddr=c00000
my_boot=bootm 0x40000000 0x41000000 0x00c00000
my_dtb=tftp 0x00c00000 $prefix/p4080ds.dtb
nohvboot=tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/$ramdiskfile;tftp c00000 $dir/$fdtfile;setenv bootargs root=/dev/ram rw ramdisk_size=0x10000000 console=ttyS0,115200;bootm 1000000 2000000 c00000;
=>

This patch also enables the grepenv command by default on
corenet_ds based boards (and repositions the DHCP command
entry to keep the list sorted).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2011-04-28 01:00:07 +02:00
Wolfgang Denk
f38536f913 Merge branch 'master' of git://git.denx.de/u-boot-arm 2011-04-27 21:48:09 +02:00
Minkyu Kang
d32a1a4caa Don't grab memory for LCD if FB address is defined
If FB address is defined specific address then don't grab memory for LCD

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
2011-04-27 19:38:11 +02:00
Matthias Weisser
d8834a1323 arm: Use optimized memcpy and memset from linux
Using optimized versions of memset and memcpy from linux brings a quite
noticeable speed (x2 or better) improvement for these two functions.

Here are some numbers for test done with jadecpu

                           | HEAD(1)| HEAD(1)| HEAD(2)| HEAD(2)|
                           |        | +patch |        | +patch |
---------------------------+--------+--------+--------+--------+
Reset to prompt            |  438ms |  330ms |  228ms |  120ms |
                           |        |        |        |        |
TFTP a 3MB img             | 4782ms | 3428ms | 3245ms | 2820ms |
                           |        |        |        |        |
FATLOAD USB a 3MB img*     | 8515ms | 8510ms | ------ | ------ |
                           |        |        |        |        |
BOOTM LZO img in RAM       | 3473ms | 3168ms |  592ms |  592ms |
 where CRC is              |  615ms |  615ms |   54ms |   54ms |
 uncompress                | 2460ms | 2462ms |  450ms |  451ms |
 final boot_elf            |  376ms |   68ms |   65ms |   65ms |
                           |        |        |        |        |
BOOTM LZO img in FLASH     | 3207ms | 2902ms | 1050ms | 1050ms |
 where CRC is              |  600ms |  600ms |  135ms |  135ms |
 uncompress                | 2209ms | 2211ms |  828ms |  828ms |
                           |        |        |        |        |
Copy 1.4MB from NOR to RAM |  134ms |   72ms |  120ms |   70ms |

(1) No dcache
(2) dcache enabled in board_init
*Does not work when dcache is on

Size impact:

C version:
   text    data     bss     dec     hex filename
 202862   18912  266456  488230   77326 u-boot

ASM version:
   text    data     bss     dec     hex filename
 203798   18912  266288  488998   77626 u-boot
222712  u-boot.bin

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-04-27 19:38:07 +02:00
Grant Likely
c3624e6ed0 Default to bootm_size() when CONFIG_SYS_BOOTMAPSZ is not defined
This patch adds a function getenv_bootm_mapsize() for obtaining the
size of the early mapped region accessible by the kernel during early
boot.  It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined,
defaults to getenv_bootm_size(), which in turn defaults to the size of
RAM.

getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize"
environmental variable.

Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-25 21:11:20 -04:00
Heiko Schocher
71d19f30d6 rtc, rv3029: add trickle charger support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-26 00:24:40 +02:00
Wolfgang Denk
9dd5dad887 Merge branch 'misc' of git://git.denx.de/u-boot-blackfin 2011-04-20 22:57:35 +02:00
Mike Frysinger
710b99385c crc32: make command optional
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-13 15:56:43 -04:00
Mike Frysinger
a641b9794b make go optional
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-13 15:56:39 -04:00
Mike Frysinger
0c79cda01b env: make import/export optional
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-13 15:56:34 -04:00
Graeme Russ
fea2572001 x86: Rename i386 to x86
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2011-04-13 19:43:28 +10:00
Wolfgang Denk
8ae86b76c6 Make STANDALONE_LOAD_ADDR configurable per board
Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR
and allow that the architecture-specific default value gets
overwritten by defining the value in the board header file.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-04-12 22:58:32 +02:00
Mike Frysinger
1ba7fd2567 Blackfin: ldrinfo: new command
Simple command to decode/check an LDR image before we try to boot it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:27 -04:00
Timur Tabi
7d3053fbf1 powerpc: clean up DIU macro definitions for Freescale reference boards
Clean up the macro defintions used to enable DIU (video) support on the
MPC8610HPCD and the MPC5121ADS so that they look more like the P1022DS,
which is newer.  Add software cursor support to all three boards.

Also document the CONFIG_FSL_DIU_FB in the README.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 22:32:18 -05:00
Lei Wen
cf946c6d09 mv: seperate kirkwood and armada from common setting
Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.

This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.

This patch is tested with compilation for armada100 and guruplug.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-02-21 08:30:55 +01:00
Yoshihiro Shimoda
6639562e6a spi: add support SuperH SPI module
SH7757 has SPI module. This patch supports it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-02-02 16:38:41 +09:00
Yoshihiro Shimoda
68260aab93 net: sh_eth: add cache handling
Some CPU needs cache handling. So this patch add the config of
CONFIG_SH_ETHER_CACHE_WRITEBACK, and it calls wback function.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-02-02 16:38:41 +09:00
Yoshihiro Shimoda
3d0075fa7a README: add description of sh_eth driver
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-02-02 16:38:41 +09:00
Alexander Holler
c6b1ee664a Fix defines needed to enable command sha1sum
Documented is CONFIG_CMD_SHA1, through confusion in the source
CONFIG_CMD_SHA1 and CONFIG_CMD_SHA1SUM has to be used to enable
sha1sum.

Fix both, the documentation and the source, so that only
CONFIG_CMD_SHA1SUM is needed to enable the command sha1sum.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
2011-01-19 09:39:10 +01:00
Wolfgang Denk
e1ccf97c5d Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2011-01-17 20:31:46 +01:00
Wolfgang Denk
aad813a342 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2011-01-17 20:11:40 +01:00
Kumar Gala
a09b9b68d4 powerpc/8xxx: Refactor SRIO initialization into common code
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO.  We mimic what we do with PCIe
controllers for SRIO.

We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.

We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.

Introduced the following standard defines for board config.h:

CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available

(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)

[ These mimic what we have for PCI and PCIe controllers ]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-14 01:32:21 -06:00
Chris Packham
5dec49ca22 pca953x: support 16-pin devices
This adds support for for the PCA9535/PCA9539 family of gpio devices which
have 16 output pins.

To let the driver know which devices are 16-pin it is necessary to define
CONFIG_SYS_I2C_PCA953X_WIDTH in your board config file. This is used to
create an array of {chip, ngpio} tuples that are used to determine the
width of a particular chip. For backwards compatibility it is assumed that
any chip not defined in CONFIG_SYS_I2C_PCA953X_WIDTH has 8 pins.

Acked-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
2011-01-10 07:53:00 +01:00
Macpaul Lin
b3dbf4a51f ftgmac100: support of gigabit eth ftgmac100
Add Faraday's ftgmac100 (gigabit ethernet)
MAC controller's driver.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-01-09 22:16:51 +01:00
Wolfgang Denk
844f07d8a1 Coding Style (white space) cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-11-27 23:35:14 +01:00
Wolfgang Denk
e03f316974 Drop support for CONFIG_SKIP_RELOCATE_UBOOT
For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE).  The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().

With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway.  So don't keep this relict any
longer.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:40:08 +02:00
Wolfgang Denk
071bc92330 Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-27 22:48:30 +02:00
Wolfgang Denk
553f09823c Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken.  Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:03:25 +02:00
John Rigby
fca43cc801 boot: change some arch ifdefs to feature ifdefs
The routines boot_ramdisk_high, boot_get_cmdline and boot_get_kbd
are currently enabled by various combinations of CONFIG_M68K,
CONFIG_POWERPC and CONFIG_SPARC.

Use CONFIG_SYS_BOOT_<FEATURE> defines instead.

CONFIG_SYS_BOOT_RAMDISK_HIGH
CONFIG_SYS_BOOT_GET_CMDLINE
CONFIG_SYS_BOOT_GET_KBD

Define these as appropriate in arch/include/asm/config.h files.

Signed-off-by: John Rigby <john.rigby@linaro.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:53:32 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Scott Wood
fdd813def8 README: Add new NAND env features
CONFIG_ENV_SIZE does not need block alignment.

Document CONFIG_ENV_RANGE and CONFIG_ENV_OFFSET_OOB.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2010-10-11 15:11:33 -05:00
Wolfgang Denk
544d97e9aa PCU_E: remove code for yet another corpse
The PCU_E board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot.  Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-06 22:22:24 +02:00
Wolfgang Denk
2e6e1772c0 Merge branch 'next' of /home/wd/git/u-boot/next
Conflicts:
	include/ppc4xx.h

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-28 23:30:47 +02:00
Thomas Weber
360d883aa0 README: Fix description of version numbering scheme
The version numbering scheme was changed in Oct, 2008.
This patch brings the documentation to the actual level.
The description is taken from:
http://www.denx.de/wiki/U-Boot/ReleaseCycle

Signed-off-by: Thomas Weber <weber@corscience.de>

Changed text slightly.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-28 14:37:58 +02:00
Stefan Roese
24956642ef Remove unused CONFIG_SERIAL_SOFTWARE_FIFO feature
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2010-09-23 09:02:05 +02:00
Stefan Roese
e3c78c9b3c ppc4xx: Remove now unused CONFIG_UART1_CONSOLE
CONFIG_UART1_CONSOLE was a PPC4xx specific implementation and is now
removed since the move from the 4xx UART driver to the common NS16550
UART driver. Let's remove all references to this define now.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Wolfgang Denk
ea882baf9c New implementation for internal handling of environment variables.
Motivation:

* Old environment code used a pessimizing implementation:
  - variable lookup used linear search => slow
  - changed/added variables were added at the end, i. e. most
    frequently used variables had the slowest access times => slow
  - each setenv() would calculate the CRC32 checksum over the whole
    environment block => slow
* "redundant" envrionment was locked down to two copies
* No easy way to implement features like "reset to factory defaults",
  or to select one out of several pre-defined (previously saved) sets
  of environment settings ("profiles")
* No easy way to import or export environment settings

======================================================================

API Changes:

- Variable names starting with '#' are no longer allowed

  I didn't find any such variable names being used; it is highly
  recommended to follow standard conventions and start variable names
  with an alphanumeric character

- "printenv" will now print a backslash at the end of all but the last
  lines of a multi-line variable value.

  Multi-line variables have never been formally defined, allthough
  there is no reason not to use them. Now we define rules how to deal
  with them, allowing for import and export.

- Function forceenv() and the related code in saveenv() was removed.
  At the moment this is causing build problems for the only user of
  this code (schmoogie - which has no entry in MAINTAINERS); may be
  fixed later by implementing the "env set -f" feature.

Inconsistencies:

- "printenv" will '\\'-escape the '\n' in multi-line variables, while
  "printenv var" will not do that.

======================================================================

Advantages:

- "printenv" output much better readable (sorted)
- faster!
- extendable (additional variable properties can be added)
- new, powerful features like "factory reset" or easy switching
  between several different environment settings ("profiles")

Disadvantages:

- Image size grows by typically 5...7 KiB (might shrink a bit again on
  systems with redundant environment with a following patch series)

======================================================================

Implemented:

- env command with subcommands:

  - env print [arg ...]

    same as "printenv": print environment

  - env set [-f] name [arg ...]

    same as "setenv": set (and delete) environment variables

    ["-f" - force setting even for read-only variables - not
    implemented yet.]

  - end delete [-f] name

    not implemented yet

    ["-f" - force delete even for read-only variables]

  - env save

    same as "saveenv": save environment

  - env export [-t | -b | -c] addr [size]

    export internal representation (hash table) in formats usable for
    persistent storage or processing:

	-t:	export as text format; if size is given, data will be
		padded with '\0' bytes; if not, one terminating '\0'
		will be added (which is included in the "filesize"
		setting so you can for exmple copy this to flash and
		keep the termination).
	-b:	export as binary format (name=value pairs separated by
		'\0', list end marked by double "\0\0")
	-c:	export as checksum protected environment format as
		used for example by "saveenv" command
	addr:	memory address where environment gets stored
	size:	size of output buffer

	With "-c" and size is NOT given, then the export command will
	format the data as currently used for the persistent storage,
	i. e. it will use CONFIG_ENV_SECT_SIZE as output block size and
	prepend a valid CRC32 checksum and, in case of resundant
	environment, a "current" redundancy flag. If size is given, this
	value will be used instead of CONFIG_ENV_SECT_SIZE; again, CRC32
	checksum and redundancy flag will be inserted.

	With "-b" and "-t", always only the real data (including a
	terminating '\0' byte) will be written; here the optional size
	argument will be used to make sure not to overflow the user
	provided buffer; the command will abort if the size is not
	sufficient. Any remainign space will be '\0' padded.

        On successful return, the variable "filesize" will be set.
        Note that filesize includes the trailing/terminating '\0'
        byte(s).

        Usage szenario: create a text snapshot/backup of the current
	settings:

		=> env export -t 100000
		=> era ${backup_addr} +${filesize}
		=> cp.b 100000 ${backup_addr} ${filesize}

	Re-import this snapshot, deleting all other settings:

		=> env import -d -t ${backup_addr}

  - env import [-d] [-t | -b | -c] addr [size]

    import external format (text or binary) into hash table,
    optionally deleting existing values:

	-d:	delete existing environment before importing;
		otherwise overwrite / append to existion definitions
	-t:	assume text format; either "size" must be given or the
		text data must be '\0' terminated
	-b:	assume binary format ('\0' separated, "\0\0" terminated)
	-c:	assume checksum protected environment format
	addr:	memory address to read from
	size:	length of input data; if missing, proper '\0'
		termination is mandatory

  - env default -f

    reset default environment: drop all environment settings and load
    default environment

  - env ask name [message] [size]

    same as "askenv": ask for environment variable

  - env edit name

    same as "editenv": edit environment variable

  - env run

    same as "run": run commands in an environment variable

======================================================================

TODO:

- drop default env as implemented now; provide a text file based
  initialization instead (eventually using several text files to
  incrementally build it from common blocks) and a tool to convert it
  into a binary blob / object file.

- It would be nice if we could add wildcard support for environment
  variables; this is needed for variable name auto-completion,
  but it would also be nice to be able to say "printenv ip*" or
  "printenv *addr*"

- Some boards don't link any more due to the grown code size:
  DU405, canyonlands, sequoia, socrates.

	=> cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
	       Stefan Roese <sr@denx.de>,
	       Heiko Schocher <hs@denx.de>

- Dropping forceenv() causes build problems on schmoogie

	=> cc: Sergey Kubushyn <ksi@koi8.net>

- Build tested on PPC and ARM only; runtime tested with NOR and NAND
  flash only => needs testing!!

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
Cc: Stefan Roese <sr@denx.de>,
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kubushyn <ksi@koi8.net>
2010-09-19 19:29:48 +02:00
Heiko Schocher
48690d8024 net ppc: fix ethernet device names with spaces
since commit 1384f3bb8a ethernet names
with spaces drop a

Warning: eth device name has a space!

message. This patch fix it for:

- "FEC ETHERNET" devices found on
  mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
  renamed to "FEC".
- "SCC ETHERNET" devices found on
  mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
  Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
  boards. Renamed to "FCC"

Tested on the kup4k board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09 11:52:28 -07:00
Wolfgang Denk
cdb749778a Rename getenv_r() into getenv_f()
While running from flash, i. e. before relocation, we have only a
limited C runtime environment without writable data segment. In this
phase, some configurations (for example with environment in EEPROM)
must not use the normal getenv(), but a special function.  This
function had been called getenv_r(), with the idea that the "_r"
suffix would mean the same as in the _r_eentrant versions of some of
the C library functions (for example getdate vs. getdate_r, getgrent
vs. getgrent_r, etc.).

Unfortunately this was a misleading name, as in U-Boot the "_r"
generally means "running from RAM", i. e. _after_ relocation.

To avoid confusion, rename into getenv_f() [as "running from flash"]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2010-08-04 00:45:36 +02:00
Mike Frysinger
793b5726f7 i2c: soft_i2c: add simple GPIO implementation
Since the vast majority of GPIO I2C implementations behave the same way,
support the common GPIO framework with default settings.

This adds two new defines CONFIG_SOFT_I2C_GPIO_{SCL,SDA} so that boards
which want GPIO I2C support need only define these.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-07-22 08:03:47 +02:00
Wolfgang Denk
a9046b9e1a Prepare v2010-rc2
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-06-13 17:48:15 +02:00
Thomas Chou
1117cbf2ad nios: remove nios-32 arch
The nios-32 arch is obsolete and broken. So it is removed.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-28 10:56:04 -04:00
Thomas Chou
0df01fd3d7 nios2: fix r15 issue for gcc4
The "-ffixed-r15" option doesn't work well for gcc4. Since we
don't use gp for small data with option "-G0", we can use gp
as global data pointer. This allows compiler to use r15. It
is necessary for gcc4 to work properly.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-05-28 10:56:03 -04:00
Ben Warren
ecee9324d7 Program net device MAC addresses after initializing
Add a new function to the eth_device struct for programming a network
controller's hardware address.

After all network devices have been initialized and the proper MAC address
for each has been determined, make a device driver call to program the
address into the device.  Only device instances with valid unicast addresses
will be programmed.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Tested-by: Prafulla Wadaskar <prafulla@marvell.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-03 14:52:49 -07:00
Wolfgang Denk
b919a3f298 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2010-04-24 21:11:56 +02:00
Stefan Roese
a47a12becf Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.

Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00
Richard Retanubun
26a33504a5 fsl_i2c: Added a callpoint for i2c_board_late_init
This patch adds a callpoint in i2c_init that allows board specific
i2c board initialization (typically for i2c bus reset) that is called
after i2c_init operations, allowing the i2c_board_late_init function
to use the pre-configured i2c bus speed and slave address.
2010-04-19 07:46:35 +02:00
Peter Tyser
8d321b81c5 Update README to reflect new directory structure
Also fix up some whitespace issues that were introduced when moving
directory locations.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:27 +02:00
Peter Tyser
8d1f268204 ppc: Move cpu/$CPU to arch/ppc/cpu/$CPU
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:16 +02:00
Peter Tyser
78acc472d9 Rename lib_generic/ to lib/
Now that the other architecture-specific lib directories have been
moved out of the top-level directory there's not much reason to have the
'_generic' suffix on the common lib directory.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:04 +02:00
Peter Tyser
ea0364f1bb Move lib_$ARCH directories to arch/$ARCH/lib
Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk

This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:03 +02:00
Anatolij Gustschin
d5011762f5 video: cfb_console.c: add support for RLE8 bitmaps
Allow displaying 8-bit RLE BMP images.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-08 15:25:43 +02:00
Wolfgang Denk
c96f86eefc TFTP: allow for adjustable retransmission timout
So far, TFTP negotiated a fixed retransmission timeout of 5 seconds.
In some cases (busy networks, slow TFTP servers) this caused very
slow transfers. A new environment variable "tftptimeout" allows to
set this timeout. Lowering this value may make downloads succeed
faster in networks with high packet loss rates or with unreliable
TFTP servers.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-03-21 22:22:44 +01:00
Jens Scharsig
c041e9d212 new at91_emac network driver (NET_MULTI api)
* add's at91_emac (AT91RM9200) network driver (NET_MULTI api)
* enable driver with CONFIG_DRIVER_AT91EMAC
* generic PHY initialization
* modify AT91RM9200 boards to use NET_MULTI driver
* the drivers has been tested with LXT971 Phy and DM9161 Phy at
  MII and RMII interface

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Joakim Tjernlund
e6bee80814 ppc: Update README about the new GOT ptr.
r14 is no longer used as non volatile GOT ptr. Instead
the volatile r12 is used so be sure to do GET_GOT in
asm code when you need to access global data.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
2010-01-26 19:30:15 +01:00
Heiko Schocher
548738b4d4 cmd_eeprom: I2C updates
- CONFIG_ENV_EEPROM_IS_ON_I2C
  define this, if you have I2C and SPI activated, and your
  EEPROM, which holds the environment, is on the I2C bus.

- CONFIG_I2C_ENV_EEPROM_BUS
  if you have an Environment on an EEPROM reached over
  I2C muxes, you can now define, how to reach this
  EEPROM.

Signed-off-by: Heiko Schocher <hs@denx.de>
2010-01-18 00:42:37 +01:00
Heiko Schocher
4b142febff common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-08 22:14:07 +01:00
Mike Rapoport
c2fff331a3 smc911x: update SMC911X related configuration description
Since commit 736fead8fd "Convert SMC911X
Ethernet driver to CONFIG_NET_MULTI API" SMC911X configration options
are called CONFIG_SMC911X rather than CONFIG_DRIVER_SMC911X. Update
README to reflect that change.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
2009-12-07 22:05:43 +01:00
Detlev Zundel
cccfc2ab77 README: Rearrange paragraphs to regain linear arrangement.
Two later additions to the Configuration Option section unfortunately
split the description of Show boot progress and the list of its call outs.

Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-12-05 01:47:45 +01:00
Robert P. J. Day
ad53226156 README: Update the list of directories.
Bring the directory listing more into line with current content.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2009-12-02 23:37:14 +01:00
Peter Tyser
246c69225c Add 'editenv' command
The editenv command can be used to edit an environment variable.
Editing an environment variable is useful when one wants to tweak an
existing variable, for example fix a typo or change the baudrate in the
'bootargs' environment variable.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-10-27 20:58:25 +01:00
Wolfgang Denk
a747a7f310 Revert "env: only build env_embedded and envcrc when needed"
Breaks building on many boards, and no really clean fix available yet.

This reverts commit 6dab6add2d.
2009-10-27 20:46:31 +01:00
Mike Frysinger
6dab6add2d env: only build env_embedded and envcrc when needed
The env code is protected by the ENV_IS_EMBEDDED define, so attempting to
compile the code when this isn't defined is pointless.  Now that the env
headers have unified around CONFIG_ENV_IS_EMBEDDED, convert the build
system to only build the env objects when this is enabled.  And now that
the env code is conditionally compiled, we can drop the source code checks.

For people who want to extract the environment manually, add a new option
CONFIG_BUILD_ENVCRC that only enables the envcrc utility.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-18 22:53:18 +02:00
Heiko Schocher
3887c3fbdb mucmc52, uc101: delete ata@3a00 node, if no CF card is detected
U-Boot can detect if an IDE device is present or not.
If not, and this new config option is activated, U-Boot
removes the ATA node from the DTS before booting Linux,
so the Linux IDE driver does not probe the device and
crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-09-25 01:22:13 +02:00
Peter Tyser
3202d33169 Remove deprecated 'autoscr' command/variables
The more standard 'source' command provides identical functionality to
the autoscr command.

Environment variable names/values on the MVBC_P, MVBML7, kmeter1,
mgcoge, and km8xx boards are updated to no longer refernce 'autoscr'.

The 'autoscript' and 'autoscript_uname' environment variables are
also removed.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
2009-09-22 23:03:24 +02:00
Marcel Ziswiler
b55ae40249 FDT: remove obsolete OF_CPU and OF_SOC macros.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@noser.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2009-09-22 22:59:27 +02:00
Eric Millbrandt
5da71efa18 Reset i2c slave devices during init on mpc5xxx cpus
Reset any i2c devices that may have been interrupted during a system reset.
Normally this would be accomplished by clocking the line until SCL and SDA
are released and then sending a start condtiion (From an Atmel datasheet).
There is no direct access to the i2c pins so instead create start commands
through the i2c interface.  Send a start command then delay for the SDA Hold
time, repeat this by disabling/enabling the bus a total of 9 times.

Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
2009-09-06 11:26:04 +02:00
Robin Getz
c4db335c2e Blackfin: change global data register from P5 to P3
Since the Blackfin ABI favors higher scratch registers by default, use the
last scratch register (P3) for global data rather than the first (P5).
This allows the compiler's register allocator to use higher number scratch
P registers, which in turn better matches the Blackfin instruction set,
which reduces the size of U-Boot by more than 1024 bytes...

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02 05:14:02 -04:00
Eric Millbrandt
307ecb6db0 Add support for USB on PSC3 for the mpc5200
Support USB on PSC3 on the mpc5200.  Before this patch, enabling USB support
would reconfigure PSC4 and PSC5 to USB.  The mpc5200 does not support USB
enabled on both the standard USB port and PSC3.  This patch masks the
appropriate bits when enabling USB.

Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Remy Bohmer <linux@bohmer.net>
2009-08-25 12:57:55 +02:00
Robin Getz
02c9aa1d41 Add md5sum and sha1 commands...
Now that we have sha1 and md5 in lib_generic, allow people to use
them on the command line, for checking downloaded files.

Signed-off-by: Robin Getz <rgetz@analog.com>
2009-08-25 12:57:54 +02:00
Robin Getz
97cfe86163 Save server's MAC address in environment
Linux's netconsole works much better when you can pass it the MAC address of
the server. (otherwise it just uses broadcast, which everyone else on my
network complains about :)

This sets the env var "serveraddr" (to match ethaddr), so that you can pass
it to linux with whatever bootargs you want to....

addnetconsole=set bootargs $(bootargs) netconsole=@$(ipaddr)/eth0,@$(serverip)/$(serveraddr)

Signed-of-by: Robin Getz <rgetz@blackfin.uclinux.org>

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22 23:17:01 -07:00
Wolfgang Denk
a694610d33 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2009-07-19 00:38:23 +02:00
Matthias Weisser
1ca298ced0 Added support for splash screen positioning
This patch adds support splash image positioning by adding an
additional variable "splashpos" to the environment. Please see
README for details.

Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2009-07-17 15:23:41 +02:00
Scott Wood
be33b046b5 Remove legacy NAND and disk on chip code.
Legacy NAND had been scheduled for removal.  Any boards that use this
were already not building in the previous release due to an #error.

The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed.  There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 19:07:47 -05:00
Jerry Van Baren
6c3fef28b9 Improve U-Boot Porting Guide in the README
Update for...
* BDI2000 -> BDI3000 (BDI2000 is obsolete).
* Add a line to read the doc/README.* files
* Fix coding standard violations

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2009-07-16 21:45:51 +02:00
Guennadi Liakhovetski
b74ab73736 nand_spl: read environment early, when booting from NAND using nand_spl
Currently, when booting from NAND using nand_spl, in the beginning the default
environment is used until later in boot process the dynamic environment is read
out. This way environment variables that must be interpreted early, like the
baudrate or "silent", cannot be modified dynamically and remain at their
default values. Fix this problem by reading out main and redundand (if used)
copies of the environment in the nand_spl code.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:07 -05:00
Magnus Lilja
df81238b3e ARM1136: Introduce CONFIG_PRELOADER macro.
Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2009-06-21 16:18:12 +02:00
Stefan Roese
d558107c18 mtd: Introduce CONFIG_MTD_DEVICE to select compilation of mtdcore.o
This new define enables mtdcore.c compilation and with this we can
select the MTD device infrastructure needed for the reworked mtdparts
command.

We now have the 2 MTD infrastructure defines, CONFIG_MTD_DEVICE and
CONFIG_MTD_PARTITIONS. CONFIG_MTD_DEVICE is needed (as explained above)
for the "mtdparts" command and CONFIG_MTD_PARTITIONS is needed for UBI.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
2009-06-12 20:45:47 +02:00
Peter Tyser
0f89c54be9 i2c: Update references to individual i2c commands
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:46 +02:00
Peter Tyser
d48eb5131d i2c: Remove deprecated individual i2c commands
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.

The functionality of the individual commands is still available via
the 'i2c' command.

This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:46 +02:00
Peter Tyser
2f8d396b93 Add support for building native win32 tools
Add support for compiling the host tools in the tools directory using
the MinGW toolchain.  This produces executables which can be used on
standard Windows computers without requiring cygwin.

One must specify the MinGW compiler and strip utilities as if they
were the host toolchain in order to build win32 executables, eg:

make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-04-04 01:21:02 +02:00
Wolfgang Denk
74de7aefd7 Add "source" command; prepare removal of "autoscr" command
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.

This patch prepares this change and starts a 6 month transition
period as follows:

- The new "source" command has been added, which implements exactly
  the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
  new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
  have *not* been adapted yet; these will be renamed resp. removed in
  a separate patch when the support for the "autoscr" command get's
  finally dropped.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-03 22:01:42 +02:00
Stefan Roese
68d7d65100 Separate mtdparts command from jffs2
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-03-20 22:39:14 +01:00
Heiko Schocher
506f391888 8xx, icache: enabling ICache not before running from RAM
with the new CONFIG_SYS_DELAYED_ICACHE config option, ICache
is not enabled before code runs from RAM.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-18 20:48:29 +01:00
Kim Phillips
c157cec3c3 README: remove duplicate entry
it's been around since the original commit (2ad6b513) that added two
identical entries.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-19 01:01:25 +01:00
Ron Madrid
f5675aa5ce Create configuration option for restricted ns16550 functions
This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error.  This option will exclude all functions with exception of
NS16550_putc and NS16550_init.  This will be used primarily to save space and
remove unused code from builds in which space is limited.

Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
2009-02-19 00:34:51 +01:00
Mike Frysinger
bdab39d358 rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENV
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment.  So, let's make sure the define is named accordingly.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-18 00:47:43 +01:00
Dirk Eibach
9cacf4fc40 ppc4xx: Add README entry for CONFIG_PCI_DISABLE_PCIE
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-12 06:18:20 +01:00
Heiko Schocher
2b3f12c214 8xx serial, smc: add configurable SMC Rx buffer len
This patch adds the configuration option CONFIG_SYS_SMC_RXBUFLEN.
With this option it is possible to allow the receive
buffer for the SMC on 8xx to be greater then 1. In case
CONFIG_SYS_SMC_RXBUFLEN == 1 this driver works as the
old version.

When defining CONFIG_SYS_SMC_RXBUFLEN also
CONFIG_SYS_MAXIDLE must be defined to setup the maximum
idle timeout for the SMC.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-11 23:18:13 +01:00
Heiko Schocher
c92fac91a0 82xx serial, smc: add configurable SMC Rx buffer len
This patch adds the configuration option CONFIG_SYS_SMC_RXBUFLEN.
With this option it is possible to allow the receive
buffer for the SMC on 82xx to be greater then 1. In case
CONFIG_SYS_SMC_RXBUFLEN == 1 this driver works as the
old version.

When defining CONFIG_SYS_SMC_RXBUFLEN also
CONFIG_SYS_MAXIDLE must be defined to setup the maximum
idle timeout for the SMC.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-10 00:54:42 +01:00
Jean-Christophe PLAGNIOL-VILLARD
b4e2f89dfc ixp: remove the option to include the Microcode
instead the board will have to load it from flash or ram
which will be specified by npe_ucode env var

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-31 09:53:39 +01:00
Peter Tyser
2fb2604d5c Command usage cleanup
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28 08:49:52 +01:00
Andrew Dyer
2ac6985a74 soft_i2c.c add option for repeated start in i2c_read()
This patch adds a #define to optionally change the behaviour of
i2c_read() in soft_i2c.c to send an I2C repeated start instead of a
stop-start between sending the device address pointer write and
reading back the data.  The current behaviour is retained as the
default.

While most devices will work either way, I have a smart battery(*)
that requires repeated start, and someone at some point found a
device that required a stop-start.

(*) http://www.inspired-energy.com/Standard_Products/NL2054/NL2054%20Rev1.0%20Data%20Sheet.pdf

Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
2009-01-27 22:26:31 +01:00
Peter Tyser
a7c9310457 Add support for Maxim's DS4510 I2C device
Initial support for the DS4510, a CPU supervisor with
integrated EEPROM, SRAM, and 4 programmable non-volatile
GPIO pins. The CONFIG_DS4510 define enables support
for the device while the CONFIG_CMD_DS4510 define
enables the ds4510 command. The additional
CONFIG_DS4510_INFO, CONFIG_DS4510_MEM, and
CONFIG_DS4510_RST defines add additional sub-commands
to the ds4510 command when defined.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-24 01:47:50 +01:00
Wolfgang Denk
f85cd46918 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2008-12-30 23:30:47 +01:00
Wolfgang Denk
0668236baf README: update mailing list name and hits to patch submission.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-30 22:56:11 +01:00
Peter Tyser
e92739d34e Add support for PCA953x I2C gpio devices
Initial support for NXP's 4 and 8 bit I2C gpio expanders
(eg pca9537, pca9557, etc). The CONFIG_PCA953X define
enables support for the devices while the CONFIG_CMD_PCA953X
define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO
define enables an 'info' sub-command which provides summary
information for the given pca953x device.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19 18:11:49 -06:00
Niklaus Giger
0b2f4ecad4 README: Document CONFIG_SYS parameters for vxworks
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
2008-12-07 00:14:56 +01:00
Piotr Ziecik
91809ed51d cfi-mtd: Add cfi-mtd driver.
Add cfi-mtd driver, which exports CFI flash to MTD layer.
This allows CFI flash devices to be used from MTD layer.

Building of the new driver is controlled by CONFIG_FLASH_CFI_MTD
option. Initialization is done by calling cfi_mtd_init() from
flash_init().

Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-24 11:05:25 +01:00
Mike Frysinger
adbfeeb7b3 Blackfin: document some of the blackfin directories
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23 05:03:50 -04:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Heiko Schocher
67b23a3228 I2C: adding new "i2c bus" Command to the I2C Subsystem.
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.

Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:02 +02:00
richardretanubun
07f3d789b9 Add support for CONFIG_EFI_PARTITION (GUID Partition Table)
The GUID (Globally Unique Identifier) Partition Table (GPT) is a part
of EFI. See http://en.wikipedia.org/wiki/GUID_Partition_Table

Based on linux/fs/partitions/efi.[ch]

Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
2008-10-18 21:54:01 +02:00
Bartlomiej Sieka
4bae90904b Automatic software update from TFTP server
The auto-update feature allows to automatically download software updates
from a TFTP server and store them in Flash memory during boot. Updates are
contained in a FIT file and protected with SHA-1 checksum.

More detailed description can be found in doc/README.update.

Signed-off-by: Rafal Czubak <rcz@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2008-10-18 21:54:00 +02:00
richardretanubun
c68a05feeb Adds two more ethernet interface to 83xx
Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.

Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-10-18 21:54:00 +02:00
Peter Tyser
0c32565f53 Update mailing list email and archive addresses
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-09-13 02:12:41 +02:00
Luigi 'Comio' Mantellini
fc9c1727b5 Add support for LZMA uncompression algorithm.
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-13 01:59:07 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD
5a1aceb068 rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
9314cee691 rename CFG_ENV_IS_IN_NVRAM in CONFIG_ENV_IS_IN_NVRAM
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:59 +02:00
Jean-Christophe PLAGNIOL-VILLARD
51bfee1920 rename CFG_ENV_IS_IN_NAND in CONFIG_ENV_IS_IN_NAND
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:58 +02:00
Jean-Christophe PLAGNIOL-VILLARD
057c849c45 rename CFG_ENV_IS_IN_DATAFLASH in CONFIG_ENV_IS_IN_DATAFLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:58 +02:00
Jean-Christophe PLAGNIOL-VILLARD
bb1f8b4f8b rename CFG_ENV_IS_IN_EEPROM in CONFIG_ENV_IS_IN_EEPROM
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:38 +02:00
Victor Gallardo
9ebbb54f7a ppc4xx: Allow DTT_I2C_DEV_CODE configured by CFG_I2C_DTT_ADDR
On AMCC Arches board DTT_I2C_DEV_CODE is different then canyonlands
and glacier.

Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
2008-09-10 11:08:45 +02:00
Peter Tyser
f5ed9e3908 Add support for booting of INTEGRITY operating system uImages
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-09-09 15:54:10 +02:00
Kumar Gala
9ba2e2c819 Remove support for booting ARTOS images
Pantelis Antoniou stated:
	AFAIK, it is still used but the products using PPC are long gone.
	Nuke it plz (from orbit).

So remove it since it cleans up a usage of env_get_char outside of
the environment code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-09 15:52:35 +02:00
Andreas Engel
48d0192fe8 Moved conditional compile into Makefile
Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
2008-09-09 14:42:02 +02:00
Markus Heidelberg
1dc306931c README: fix missing subdirectory in the documentation
Signed-off-by: Markus Heidelberg <markus.heidelberg@web.de>
2008-09-09 12:05:26 +02:00
Jean-Christophe PLAGNIOL-VILLARD
00b1883a4c drivers/mtd: Move conditional compilation to Makefile
rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:42 +02:00
Magnus Lilja
0d28f34bbe Update the U-Boot wiki URL.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2008-08-11 00:08:01 +02:00
Marcel Ziswiler
11ccc33fa2 Many spelling fixes in README.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-07-10 00:50:05 +02:00
Wolfgang Denk
cdeb62e20d Merge branch 'master' of git://www.denx.de/git/u-boot-fdt 2008-06-11 22:30:47 +02:00
Gerald Van Baren
fec6d9ee7c Remove the deprecated CONFIG_OF_FLAT_TREE
Use CONFIG_OF_LIBFDT instead to support flattened device trees.  It is
cleaner, has better functionality, and is better supported.

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2008-06-09 21:13:35 -04:00
Ben Warren
e44f3ea4e8 Merge branch 'master' of git://git.denx.de/u-boot 2008-06-08 22:04:22 -07:00
Jean-Christophe PLAGNIOL-VILLARD
42fd5f87b1 Merging Stelian Pop AT91 patches
Merge branch 'testing-V2'

Conflicts:

	board/atmel/at91cap9adk/Makefile
                Fixing copyright
	board/atmel/at91sam9260ek/Makefile
                Fixing copyright
	board/atmel/at91sam9260ek/u-boot.lds
                Delete no more needed ld script

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-24 12:56:53 +02:00
Jens Gehrlein
557b377d8b smc911x: add 16 bit support
Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-05-22 23:10:01 -07:00
Stelian Pop
39cf480484 Add ATMEL LCD driver
This patch adds support for the ATMEL LCDC driver which is used on some
AT91 and AVR platforms.

Is has been tested with the AT91CAP9ADK, AT91SAM9261EK, AT91SAM9263EK and
AT91SAM9RLEK boards. Adaptation for AVR32 should probably be easy.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:44:55 +02:00
Adrian Filipi
8fbc985bda Fix some typos
This patch fixes three typos.
The first is a repetition of CONFIG_CMD_BSP.
The second makes the #endif comment match its #if.
The third is a spelling error.

Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
2008-05-09 20:53:52 +02:00
Guennadi Liakhovetski
40cb90ee2b net: make ARP timeout configurable
Currently the timeout waiting for an ARP reply is hard set to 5 seconds.
On i.MX31ADS due to a hardware "strangeness" up to four first IP packets
to the boards get lost, which typically are ARP replies. By configuring
the timeout to a lower value we significantly improve the first network
transfer time on this board. The timeout is specified in milliseconds,
later internally it is converted to deciseconds, because it has to be
converted to hardware ticks, and CFG_HZ ranges from 900 to 27000000 on
different boards.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-04-28 22:23:21 -07:00
Guennadi Liakhovetski
7ce6370982 RTC driver for MC13783
MC13783 is a multifunction IS with an SPI interface to the host. This
driver handles the RTC controller in this chip.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-18 00:43:50 -07:00
Guennadi Liakhovetski
38254f45b0 New i.MX31 SPI driver
This is an SPI driver for i.MX and MXC based SoCs from Freescale. So far
only implemented and tested on i.MX31, can with a modified register layout
and definitions be used for i.MX27, I think, MXC CPUs have similar SPI
controllers too.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-18 00:43:23 -07:00
Bartlomiej Sieka
7d721e34ae Boot-related documentation update
- document 'bootm_low' and 'bootm_size' environment variables
- update inaccurate CFG_BOOTMAPSZ entry

Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2008-04-17 23:35:23 -07:00
Wolfgang Denk
d6f98e76a0 Merge branch 'master' of git://www.denx.de/git/u-boot-cfi-flash 2008-04-13 09:40:35 -07:00
Guennadi Liakhovetski
96ef831f71 cfi_flash: Support buffered writes on non-standard Spansion NOR flash
Some NOR flash chip from Spansion, for example, the s29ws-n MirrorBit
series require different addresses for buffered write commands. Define a
configuration option to support buffered writes on those chips. A more
elegant solution would be to automatically detect those chips by parsing
their CFI records, but that would require introduction of a fixup table
into the cfi_flash driver.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-12 08:59:09 +02:00