When u-boot is compiled for PXA25x processor, pxa/start.S is calling
cpu_init_crit by BL instruction. BL is overwriting lr register so
relocate_code is going into infinite loop. This patch preservs lr
register in r12 before calling cpu_init_crit and after function returns
restores it.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Mobile storage is used the CLK_DIV_FSYS3 value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
To get exactly clock value for mmc, support the get_mmc_clk() like
set_mmc_clk().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With VPLL as source clock to FIMD,
Exynos DP Initializaton was failing sometimes with unstable clock.
Changing FIMD source to MPLL resolves this issue.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add workaround for the following ARM errata: 743622 and 751472.
The motivation for this change is the following kernel commit 62e4d357a
(ARM: 7609/1: disable errata work-arounds which access
secure registers), which removes the errata from multiplatform kernel.
Since imx has been converted to multiplatform in the kernel, we need to apply
such workarounds into the bootloader.
Workaround code has been taken from arch/arm/mm/proc-v7.S from 3.7.1 kernel.
Explanation of each erratum is provided at "Chip Errata for the i.MX 6Dual/6Quad"
document available at: cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().
Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).
Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Api is added to decode peripheral id based on the interrupt number
of the peripheral.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add pinmux settings for Exynos4 for mmc0 and mmc2
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds functions to extract clock frequency of Exynos4x12 IPs.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.
This patch add pinmux for I2C for Exynos4
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
This patch adds i2c clock for Exynos4
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
This algorithm computes the values of TIMING{0,1,2} registers for the
MX28 I2C block. This algorithm was derived by using a scope, but the
result seems correct.
The resulting values programmed into the registers do not correlate
with the contents in datasheet. When using the values from the datasheet,
the I2C clock were completely wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
The reset procedure works on watchdog timer while before it was modifying
TIMER_1 registers.
Tested on DM365.
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
DMM_LISA_MAP registers program whether memory is mapped
on particular EMIF or not. Irrespective of these registers
EMIF is getting configured. Correcting the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Git commit d417d1db5f replaced the
omap-common file reset.S with reset.c, but the Makefile was not
adjusted for that.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
No functional changes, just more comments for readability when a
preprocessor check spans more than a few lines, and for consistency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings. This saves about
90 bytes of space in SPL.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
AM33XX has Error Location Module (ELM) that can be used in conjuction
with GPMC controller to implement BCH codes fully in hardware.
This code is mostly taken from arago tree.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
TI AM33XX has the same GPMC controller as OMAP3 so we could just use the
existing omap_gpmc driver. This patch adds adds required
definitions/intialization.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Include asm/arch/sys_proto.h for gpmc_init prototype.
Without this we get a warning while building for AM335x.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
These GPMC_CS defines are a leftover from prior gpmc_init(). Commit 187af954
removed the need for these definitions but missed to remove them.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Conflicts:
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/woodburn_common.h
board/woodburn/woodburn.c
These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.
Fix all conflicts and update woodburn to use Power Framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Use a generic 'dram_vals[]' array that has the full initialization
sequence and rename the initialization method so it doesn't has a
frequency on its name.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The MXS SPL didn't mark local functions "static". Fix it. This also makes the
SPL smaller by roughly 300 bytes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The memory setup code adjusted the VDDD voltage. Remove this adjustment
and configure the VDDD voltage correctly in the power supply setup code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Implement common function to setup the VDDIO, VDDD and VDDA voltage.
Right now, there are two almost identical functions to setup VDDIO
and VDDD, which is prone to breakage. Pull out the differences into
constant structure and pass them as an argument to the common function.
Moreover, the function has almost identical loops for setting higher
and lower VDDx voltage. Merge these two loops.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
AM33xx has support for dual port MUSB OTG controller. This patch
adds initialization for the controller using new MUSB gadget
driver and ether gadget.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
