The address value and size value set for QSPI dts node "reg"
property have type of u64 on arm64.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is mandatory, otherwise the USB does not work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
This is a binding which only exists in U-Boot, but is
required to get working serial in U-Boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import the upstream kernel dts into U-Boot. Currently
only serial is supported, but a lot more DT changes are
queued for v4.7.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
PH1-LD20 does not support 1.8V signaling for SD card; only Default
Speed and High Speed (up to 50MHz) with 3.3V signaling is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtgrep would not accept uniphier-ph1-ld20-ref.dtb
and uniphier-ph1-ld11-ref.dtb unless the aliases node comes
the first in the root node.
$ make -s uniphier_pxs2_ld6b_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-ld20-ref
[snip]
LDS spl/u-boot-spl.lds
LD spl/u-boot-spl
OBJCOPY spl/u-boot-spl-nodtb.bin
FDTGREP spl/u-boot-spl.dtb
Error at 'fdt_find_regions': FDT_ERR_BADLAYOUT
/aliases node must come before all other nodes
Error: FDT_ERR_BADMAGIC
make[1]: *** [spl/u-boot-spl.dtb] Error 1
make: *** [spl/u-boot-spl] Error 2
This commit moves the aliases node as the error message from the
fdtgrep tool suggests, although this requirement does not sound
reasonable to me.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This enables full ethernet usage, including U-Boot to write the board
specific MAC address (ethaddr) into the DT blob before passing it to
Linux.
Without this, the ethaddr is not detected in U-Boot at all, resulting
in this error upon bootup:
...
Model: EBV SOCrates
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Fix a small typo in some of the SoCFPGA dts files that has spread via
copy-and-paste.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA72x and AM57xx EVMs the card detect gpio is designed as
active low gpio. So correcting the dt card detect gpio
definition.
Also adding card-detect gpio for DRA74x EVM.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds the sata port phy OOB timing values in the sata
device-tree node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline kernel has no r1p12 compatible string that's why console stops
to work with the latest DTS files. Append generic compatible string.
Keep in your mind that using this generic compatible string not all uart
features will be available.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modifying device tree node to support legacy interrupts.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GPIO driver supports an input interrupt that's why gpio node itself can
be labeled as interrupt controller.
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds ddrc memory controller node in dts.
size mentioned in dts is 0x30000, because we need to access DDR_QOS
INTR registers located at fd090208 from this driver.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP DMA's main clock and apb clock are added
in zynqmp DT.
Signed-off-by: VNSL Durga <vnsldurg@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
ZynqMP is not using global interrupt-parent setting that's why
it has to be listed in every node separately. PMU node missed it and
this patch is adding it.
Reported-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add power-domains to the DT and attach devices to them.
The power-domains are all logical domains as understood by firmware.
Each PD is identified by a unique identifier that the platform firmware
understands.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds broken-tuning property to SD and
eMMC nodes.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove jumbo properties which are handled in the driver directly
and use mainline compatible string which is already handled by the
driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add 8-bit bus width property to eMMC node.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes compatible string as "m25p80" for qspi node in
ep108 device tree file
Signed-off-by: Ranjit Waghmode <ranjit.waghmode@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all ZynqMP device trees inline
with each other.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing adv7511 and configure to match Base TRD.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Reviewed-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
