We are using "u-boot,spl-boot-order" now and re-use the
definition from rk3288-u-boot.dtsi, so remove it directly here.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk3288 has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Only firefly-rk3288 has the dts node "u-boot,boot-led",
while CONFIG_SPL_LED is not enable, move code to firefly-rk3288
now in case someone need this code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update to fix warning:
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/uboot@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/optee@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/fdt@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /configurations/conf@1
has a unit name, but no reg property
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk322x has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk3188 has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
SPL bootrom support is a boot device just like mmc and etc,
use formal boot device instead of jump to bootrom directly.
Enable the Kconfig by default if ROCKCHIP_BACK_TO_BROM is enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Init CPU frquency in clock driver instead of in SPL board file,
this will help for use common board file later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The common spl board file handles board_init_f() in SPL,
and with board_early_init_f() and arch_cpu_init() callback,
other operateion after board_init_f() should go to board specific
spl_board_init().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the ddc-i2c-bus device tree property which allows
for using an external i2c master for reading the display's EDID.
Signed-off-by: Niklas Schulze <me@jns.io>
Add support for the new mode_valid() display op to filter out unsupported
display DMT timings.
This is useful when connected to 4k displays, since we only support DMT
monitors up to 1920x1080, the 4k native timings are discarded to select
supported timings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a new display op, mode_valid() to be used with the newly
introduced edid_get_timing_validate() function, to filter supported
monitor timings if handled by the display driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The original edid_get_timing() function returns the first valid timing,
but on some plaforms, we could only supports a subset of the listed
monitot's navite timing.
Let's introduce a edid_get_timing_validate() adding a mode_valid callback
including a private cookie pointer.
If the callback returns false, the current timing is discared and the next
one is checked. If no valid & supported timings are found, the function
would return an error.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
in case of bmp_logo, the video_bmp driver is used for
drawing a bmp logo. This driver supports only "full"
bmp data. Adding a logo with the bmp_logo tool to
u-boot binary adds currently only real data and drops
the bmp header.
This patch adds now the full bmp data to the u-boot
binary, so video_bmp driver works with the logo embedded
into u-boot.
Fixed also some checkpatch error poping up with this
patch.
Signed-off-by: Heiko Schocher <hs@denx.de>
Use CONFIG_DM_VIDEO=y by default for Colibri iMX6ULL.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Provide proper display timings for lcdif node, used by mxsfb DM_VIDEO
enabled framebuffer driver.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
1. This fixes linking issues when building with DM_VIDEO enabled mxsfb
driver.
2. Provide proper defines for both VIDEO=y and DM_VIDEO=y.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Fix lcdif DT node and make it conform to the structure defined in the
Linux devicetree bindings [1]. Currently there is support only for
old style lcdif node definitions.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add support for display and bits-per-pixel properties.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add dumb node for NXP Display Control Unit0(DCU), which permits DM_ENABLED
converted driver to be probed. Currently no display timings are provided
in this node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to fsl_dcu_fb device.
Currently display timings aren't obtained from DT.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Move dcu-related code to fsl_dcu_probe_common, keep in video_hw_init()
only legacy video stack (filling GraphicPanel struct etc.).
Add wrappers for all init functions, that will let to provide
struct fb_info as an additional param (needed for further moving it from
the global scope to driver private data struct in DM converted driver).
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
ttyO2 console enables legacy CONFIG_SERIAL_OMAP driver in kernel.
Nowadays it's preferred to use the generic CONFIG_SERIAL_8250_OMAP
driver, which being enabled via ttyS2 console. Both drivers are enabled
in multi_v7_defconfig and in omap2plus_defconfig, for compatibility
reasons. Let's switch to ttyS2 console, to be sure that standard 8250
serial driver is used.
Similar behavior can be also achieved by enabling
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP option in kernel, but it's better not
to rely on that, as it can be disabled or removed after transitional
period.
Right now on DRA7/AM57x platforms the 8250-omap driver is being probed
first, and omap-serial driver is only probed if the first one failed.
It can be seen from uart3 definition in arch/arm/boot/dts/dra7-l4.dtsi:
compatible = "ti,dra742-uart", "ti,omap4-uart";
So the kernel already uses 8250 driver. This change basically allows
kernel developers to throw away the omap-serial driver and associated
compatibility options. Similar discussions [1,2] have started several
years ago, so it should be safe to do that now.
[1] https://patchwork.kernel.org/patch/6198471/
[2] http://processors.wiki.ti.com/index.php/Sitara_Linux_UART_-_Switching_to_8250_Driver
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
[trini: Update omap5_uevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
linux-mainline with multi_v7_defconfig + Android configs takes more
space than regular TI Android kernel and bootm will fail to load it.
Let's increase max kernel size up to 64 MiB to make it possible to run
such kernel.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The DA8850-evm supports DM_I2C and boots with SPL_DM, so we can
drop some of the code which disables DM_I2C in SPL. This
patch removes some #undef's now rendered obsolete.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SOM-LV and Torpedo boards are very similar, but something
happened growing SPL enough to break the Torpedo. The SOM-LV
board were not doing alias sequencing during SPL and they
continue to work while something broke the Torpedo. This
patch disables SPL_DM_SEQ_ALIAS allowing it to boot again.
Signed-off-by: Adam Ford <aford173@gmail.com>
OHCI was added with DM_USB support, so there are a few unneeded
items in the header file that can be removed. This also
unifies da850evm with NOR and NAND booting options so all have
OHCI support.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate da850_am18xxevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch enables the pinmuxing to support gpio_57 for phy reset
and fixes the pinmuxing for the ECHI tranceiver. The clocks
don't appear to by fully enabled yet, so OMAP-EHCI on am3517 is
still not yet working, but we're one step closer.
Signed-off-by: Adam Ford <aford173@gmail.com>
The OMAP35 and AM/DM37 Torpedo boards do not have a USB
tranceiver connected to the USB host port, so this patch
removes it from the defconfig files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SOM-LV boards support the OMAP EHCI driver using port 2.
With the driver updated to support device tree, this patch sets
the corresponding pin muxing for the tranceiver as well as the
reset pin.
Signed-off-by: Adam Ford <aford173@gmail.com>
With both SPL and U-Boot now supporting DM, we can start removing
legacy code. This patch removes the legacy MMC initalization and
legacy I2C initialization since both are now available via DM and
device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Like the other Logic PD OMAP35/DM37 boards, this board has device
tree enabled for U-Boot. This patch converts the board to enable
SPL_OF_CONTROL and further shrinks the device tree in SPL to limit
it to UART3 (console), MMC1, i2c1, and GPIO4 (for mmc1 CD and WP).
There appears to be a bug in minicom so users may need to
switch the minicom terminal emulation to ANSI from VT102 due
to the junk that gets pushed out of the UART on startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
arch_cpu_init() initializes the pinmuxing which is called fairly
early in the start sequences, so the board_init function doesn't
need to do it again. This patch removes the call from board_init.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Low Level init functions start the UART, so it doesn't need
to happen during board_init. This patch removes it from
board_init.
Signed-off-by: Adam Ford <aford173@gmail.com>
The reset line going to the ethernet controller is controlled
by a global reset controlling multiple peripherals. There
is no need to manually invoke the reset.
Signed-off-by: Adam Ford <aford173@gmail.com>
