Commit Graph

35 Commits

Author SHA1 Message Date
Bo Shen
c83cb5f665 Net: macb: reset GBE bit when fallback checking
If the GBE bit is set, when do next time autonegotiation,
if the result is not 1000Mbps, it will fallback to 100Mbps
checking. So, we need to clear the GBE bit.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-03-18 23:36:09 +01:00
Bo Shen
cabf61ce4b net: macb: enable GMAC IP without GE feature support
The User Register in GMAC IP is used to select interface type.
When with GE feature, it is used to select interface between
RGMII and GMII. If without GE feature, it is used to select
interface between MII and RMII.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:18 -05:00
Bo Shen
b2eff08869 net: macb: write mac address when initialization
When boot up without mac address setting, it will give the warning
message like: "Warning: failed to set MAC address", however when
execute network related command, it still execute them without any
warning information.

With this patch, it will exit directly with following information:
"gmac0: mac address is not valid"

It also solve the problem after bootup then set mac address and the
mac address won't set to net device issue.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:15 -05:00
Andreas Bießmann
476095772f macb: simplify gmac initialisation
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Bo Shen <voice.shen@atmel.com>
2014-10-10 21:51:15 +02:00
Wu, Josh
5ae0e38278 net: macb: enable dcache in macb
Add to code to flush the dcache after we writing in DMA buffer.
Also we need invalidate the dcache before we check the status in the
DMA buffer.

Tested in SAMA5D3x-EK with gmac0. Tftp download speed shows in below:
	Disable DCache: 1.1 MiB/s
	Enable DCache: 1.6 MiB/s
Increase speed with about 40%.

The code should have no impact with the boards which are not
enable_dcache().
Tested in AT91SAM9M10G45EK.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-06-14 18:07:01 +02:00
Andreas Bießmann
ceef983bf9 macb: make checkpatch clean
This also renames the CONFIG_SYS_MACB_xx defines. They are used just local and
therefore don't need the CONFIG_SYS_ prefix.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
2014-06-14 18:07:00 +02:00
Bo Shen
32e4f6bf2e net: macb: get DMA bus width from design config register
Get DMA bus width from design config register

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04 20:32:31 +01:00
Bo Shen
8314ccd8d4 net: macb: fix the following building warning
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22 16:49:29 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Bo Shen
d256be29f8 net: macb: add support for gigabit MAC
Add gigabit MAC support in macb driver
  - using IP version to distinguish whether MAC is GMAC

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-06-24 19:11:16 -05:00
Bo Shen
b1a0006eba net: macb: using phylib to configure phy device
using phylib to configure phy device in macb driver

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-06-24 19:11:15 -05:00
Bo Shen
d8f64b4441 net: macb: using AT91FAMILY replace #ifdeferry
Using CONFIG_AT91FAMILY replace #ifdeferry for atmel SoC

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-06-24 19:11:15 -05:00
Joe Hershberger
1b8c18b971 net: Fix build regression in macb.c
The added weak symbol must not be static.

This was introduced in 416ce623fb

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2013-06-24 19:10:42 -05:00
Shiraz Hashim
416ce623fb net/macb: Add arch specific routine to get mdio control
SPEAr310 and SPEAr320 Ethernet interfaces share same MDIO lines to control their
respective phys. Currently there is a fixed configuration in which only a
particular MAC can use the MDIO lines.

Call an arch specific function to take control of specific mdio lines at
runtime.

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>
2013-06-24 19:10:16 -05:00
Kim Phillips
eef1cf2d5c include/linux/byteorder: import latest endian definitions from linux
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives.  Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h.  They come with 'const' added for some swab functions, so
fix those up, too:

include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]

Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).

We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:

macb.c:54:0: warning: "barrier" redefined [enabled by default]

In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)).  This fixes
arch/powerpc/lib/bootm.c:

bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token

powerpc sparse builds yield:

include/common.h:356:22: error: marked inline, but without a definition

the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'

also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]

and:

Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here

and:

In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
2012-11-04 11:00:34 -07:00
Wolfgang Denk
a6f0c4faa4 Merge branch 'master' of git://git.denx.de/u-boot-avr32
* 'master' of git://git.denx.de/u-boot-avr32:
  net:macb: add line break
  avr32:portmux: fix setup for macb1
  avr32: Remove redundant LDSCRIPT definition

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-09-04 09:17:27 +02:00
Andreas Bießmann
6ed0e94071 net:macb: add line break
Without this patch we see annoying output like this:

---8<---
U-Boot> dhcp
macb1: PHY not foundmacb0: PHY present at 1
macb0: Starting autonegotiation...
--->8---

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
2012-09-03 23:39:11 +02:00
Bo Shen
f7fa2f3740 arm : Atmel : add at91sam9x5ek board support
Add at91sam9x5ek board support, this board support the following SoCs
  AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35

Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 14:58:14 +02:00
Joe Hershberger
9d9a89be3a drivers/net/macb.c: Fix compile warning
Fix this:
macb.c: In function 'macb_eth_initialize':
macb.c:564:15: warning: assignment from incompatible pointer type

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
2012-05-22 10:18:16 -05:00
andreas.devel@googlemail.com
6c169c12d7 macb: fix compile warning
This patch fixes following compile warning:

---8<---
macb.c: In function 'macb_write_hwaddr':
macb.c:525:2: warning: dereferencing type-punned pointer will break strict-aliasing rules
--->8---

Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
2011-06-21 22:26:22 +02:00
Reinhard Meyer
329f0f52fa ATMEL: fix related common atmel driver files
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18 07:56:51 +02:00
Mike Frysinger
5700bb6352 miiphy: constify device name
The driver name does not need to be writable, so constify it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09 11:52:29 -07:00
Ben Warren
6bb4679017 Write MAC address automatically on MACB-based boards
Also, remove all calls to eth_init() in boards that use MACB

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12 00:14:29 -07:00
Semih Hazar
0f751d6ef3 macb: Fix mii_phy_read and mii_phy_write functions
Enabling CONFIG_CMD_MII in AVR32 boards was not possible due to
compile errors.

This patch fixes miiphy_read and miiphy_write functions and
registers them properly.

Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Sedji Gaouaou
22ee647380 at91: Introduction of at91sam9g45 SOC.
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:43:34 +02:00
Nicolas Ferre
df486b1fa3 at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 14:48:16 +01:00
Gunnar Rangoy
fc01ea1e27 AVR32: macb - Search for PHY id
This patch adds support for searching through available PHY-addresses in
the macb-driver. This is needed for the ATEVK1100 evaluation board,
where the PHY-address will be initialized to either 1 or 7.

This patch adds a config option, CONFIG_MACB_SEARCH_PHY, which when
enabled tells the driver to search for the PHY address.

Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-28 23:59:28 -08:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Ben Warren
89973f8a82 Introduce netdev.h header file and remove externs
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02 21:18:16 -07:00
Shinya Kuribayashi
3b904ccb93 net: Conditional COBJS inclusion of network drivers
Replace COBJS-y with appropriate driver config names.

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-09 23:21:05 -07:00
Stelian Pop
8e429b3eee AT91SAM9263EK support
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:34:29 +02:00
Stelian Pop
0176d43e75 Add support for AT91SAM9260EK
Support for booting from internal DataFlash, external DataFlash card
or NAND flash is available.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-04-01 01:46:12 +02:00
Stelian Pop
7263ef191b AT91CAP9 support : MACB changes
Signed-off-by: Stelian Pop <stelian <at> popies.net>
Acked-by: Haavard Skinnemoen <hskinnemoen <at> atmel.com>
2008-02-14 09:37:58 +00:00
Ben Warren
422b1a0160 Fix Ethernet init() return codes
Change return values of init() functions in all Ethernet drivers to conform
to the following:

    >=0: Success
    <0:  Failure

All drivers going forward should return 0 on success.  Current drivers that
return 1 on success were left as-is to minimize changes.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-By: Timur Tabi <timur@freescale.com>
2008-01-10 01:06:02 +01:00
Jean-Christophe PLAGNIOL-VILLARD
2439e4bfa1 drivers/net : move net drivers to drivers/net
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25 18:35:17 +01:00