Commit Graph

463 Commits

Author SHA1 Message Date
Tom Rini
98bc1228c8 am335x_evm: Add am335x_evm_usbspl build target
We add USB (RNDIS gadget) SPL support as a separate target.  We need to
pull out YMODEM support in order to be a small enough target binary.

Signed-off-by: Tom Rini <trini@ti.com>
2013-03-08 16:41:12 -05:00
Albert ARIBAUD
a5627914da Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-02-21 21:30:47 +01:00
Albert ARIBAUD
03268374db Merge 'u-boot-microblaze/mainline/arm' into 'u-boot-arm/master'
This pulls the three following ZYNQ commits into ARM master:

7dca54f8: xilinx: zynq: Enable DCC and create new zynq_dcc board
59c651f4: arm: zynq: Add SLCR support with system reset
00ed3458: arm: zynq: Add lowlevel initialization to C
2013-02-21 16:43:19 +01:00
Tom Rini
4adfcd68cc am335x evm: Add am335x_evm_spiboot target
This target will move the environment into SPI flash and documents
the expected layout.  We correct the SPL define for where U-Boot is
and remove an unused define.

Signed-off-by: Tom Rini <trini@ti.com>
2013-02-18 13:51:20 -05:00
Enric Balletbo i Serra
d9aacf4190 OMAP3: igep00x0: Add new IGEP COM PROTON.
The IGEP COM PROTON is a new ultra compact module design with an
on-board ethernet controller.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-02-18 13:51:19 -05:00
Simon Glass
7e8c53d7d4 x86: Remove eNET boards
These are no longer used and should be removed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
2013-02-14 20:18:58 -08:00
Tom Rini
951c6baaf4 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-02-12 10:18:31 -05:00
Tom Warren
07067145de Tegra114: Add/enable Dalmore build (T114 reference board)
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-02-11 10:35:26 -07:00
Lars Poeschel
1c1b7c3739 pcm051: Add support for Phytec phyCORE-AM335x
The board is named pcm051 and has this hardware:
SOC: TI AM3359
DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB
ETH 1: LAN8710AI
SPI-Flash: W25Q64BVSSIG
RTC: RV-4162-C7
I2C-EEPROM: CAT32WC32
NAND: MT29F4G08_VFPGA63
PMIC: TPS65910A3
LCD

Supported:
UART 1
MMC/SD
ETH 1
USB
I2C
SPI

Not yet supported:
NAND
RTC
LCD

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
[trini: Add #define CONFIG_PHY_ADDR 0 to config]
Signed-off-by: Tom Rini <trini@ti.com>
2013-02-07 10:36:26 -05:00
Javier Martinez Canillas
77eea28074 OMAP3: use a single board file for IGEP devices
Even when the IGEPv2 board and the IGEP Computer-on-Module
are different from a form factor point of view, they are
very similar in the fact that share many components and how
they are wired.

So, it is possible (and better) to have a single board file
for both devices and just use the CONFIG_MACH_TYPE to make
a differentiation between each board when needed.

This change avoids code duplication by removing 298 lines of
code and makes future maintenance easier.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-02-07 10:36:25 -05:00
Michal Simek
7dca54f872 xilinx: zynq: Enable DCC and create new zynq_dcc board
Enable DCC driver for arm zynq platform to be compiled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-02-07 09:18:41 +01:00
Albert ARIBAUD
e5f5c4a977 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-02-02 19:29:59 +01:00
Prabhakar Kushwaha
41d910118c powerpc/85xx: Add BSC9132QDS support
BSC9132QDS is a Freescale reference design board for BSC9132 SoC.
BSC9132 SOC is an integrated device that targets the evolving Microcell,
Picocell, and Enterprise-Femto base station market subsegments.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.

BSC9132QDS Overview
 --------------------
  2Gbyte DDR3 (on board DDR), Dual Ranki
  32Mbyte 16bit NOR flash
  128Mbyte 2K page size NAND Flash
  256 Kbit M24256 I2C EEPROM
  128 Mbit SPI Flash memory
  SD slot
  USB-ULPI
  eTSEC1: Connected to SGMII PHY
  eTSEC2: Connected to SGMII PHY
  PCIe
  CPRI
  SerDes
  I2C RTC
  DUART interface: supports one UARTs up to 115200 bps for console display

Apart from the above it also consists various peripherals to support DSP
functionalities.

This patch adds support for mainly Power side functionalities and peripherals

Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30 11:25:14 -06:00
York Sun
b5b06fb7b0 powerpc/b4860qds: Added Support for B4860QDS
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.

B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
  ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,  ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
  16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
  8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
  RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
  connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
  connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
  configuration reset source. The RCW source is set by appropriate
  DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
	- On-board eCWTAP controller with ETH and USB I/F
	- JTAG/COP 16-pin header for any external TAP controller
	- External JTAG source over AMC to support B2B configuration
	- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
	- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
  DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
  - total four refclk, including CPRI clock scheme

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30 11:25:11 -06:00
Otavio Salvador
81ca840976 mx23evk: Add initial board support
The following features are supported:
 * 128 MB DDR1 SDRAM
 * DUART
 * SD/MMC Card Socket

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-28 11:51:04 +01:00
Marek Vasut
64a9386080 mxs: Add MX23 olinuxino board support
This patch adds support for MX23-based Olinuxino board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:22 +01:00
Kim Phillips
a6187dccd8 Merge remote-tracking branch 'mpc83xx/next' 2013-01-16 18:34:09 -06:00
Tom Warren
f01b631f7d Tegra30: Add/enable Cardhu build (T30 reference board)
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.

include/configs/tegra-common.h now holds common config options
for Tegra SoCs.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-01-16 13:40:08 -07:00
Bo Shen
961ffc7759 arm: at91sam9x5: add dataflash boot support
Add dataflash boot support on at91sam9x5ek board

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-01-12 13:18:50 +01:00
Tom Rini
7a8e739cd5 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-01-11 14:38:24 -07:00
Albert ARIBAUD
7202e8ae51 ARM: lacie_kw: add support for WIRELESS_SPACE
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-01-09 04:12:10 +05:30
Tom Rini
da77a0e593 Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-12-22 05:55:19 -07:00
Tom Rini
42e1321874 Merge branch 'master' of git://git.denx.de/u-boot-sh 2012-12-20 10:53:20 -07:00
Yoshihiro Shimoda
1a2621bab8 sh: add support for sh7752evb board
The R0P7752C00000RZ board has SH7752, 512MB DDR3-SDRAM, SPI ROM,
Gigabit Ethernet, and eMMC.

This patch supports the following functions:
 - 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMC

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-12-20 13:20:17 +09:00
Scott Wood
22f4442d12 powerpc/mpc83xx: convert MPC8313ERDB to new-SPL
This converts MPC8313ERDB NAND boot to use the new SPL infrastructure.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-12-19 17:45:54 -06:00
Jens Scharsig (BuS Elektronik)
46dc5bcade coldfire: eb_cpu5282: fix: boot from internal flash
* By a sequence of unfavorable conditions in the config header file, the eb_cpu5282
  booting from  internal stopped after relocation. Blame it is a faulty value of
  CONFIG_SYS_MONITOR_BASE. This patch fix this by replace the wrong condition in
  config header with option in board.cfg

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2012-12-19 15:51:58 -07:00
Minkyu Kang
2c601c7208 Merge branch 'master' of git://git.denx.de/u-boot into resolve
Conflicts:
	README
	board/samsung/universal_c210/universal.c
	drivers/misc/Makefile
	drivers/power/power_fsl.c
	include/configs/mx35pdk.h
	include/configs/mx53loco.h
	include/configs/seaboard.h
2012-12-10 14:13:27 +09:00
Gabe Black
112a575e49 x86: Override calculate_relocation_address to use the e820 map
Because calculate_relocation_address now uses the e820 map, it will be able
to avoid addresses over 32 bits and regions that are at high addresses but
not big enough for U-Boot. It also means we can remove the hack which
limitted U-Boot's idea of the size of memory to less than 4GB.

Also take into account the space needed for the heap and stack, so we avoid
picking a very small region those areas might overlap with something it
shouldn't.

Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2012-12-06 14:30:42 -08:00
Stefan Roese
13b4f63949 mpc5200: Add a3m071 board support
This patch adds support for the a3m071 board based on the
MPC5200.

Signed-off-by: Stefan Roese <sr@denx.de>
2012-12-05 17:31:23 +01:00
Tom Rini
a86fcff695 Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xx 2012-11-28 08:30:21 -07:00
Timur Tabi
d31e53b42c powerpc/85xx: add support for the Freescale P5040DS Superhydra reference board
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:28:06 -06:00
Wu, Josh
b7e3129e55 mmc: at91sam9x5: support to save environment in mmc
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 17:26:47 -06:00
Jens Scharsig (BuS Elektronik)
d858c335bf M68K: eb_cpu5282: general update and enhanced board support
- update clock settings for higher perfomance
- change standard baud rate to 115200
- fix flash base address
- remove unused defines
- add I2C support
- switch form board dependent flash to cfi
- remove board dependent flash code
- use sdram bank 0 instead of bank 1 on boot
- enable on board frame buffer instead external
- remove fake mac address form config
- add watchdog support
- add status led support

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
[agust: fixed small style issues and build warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-11-14 12:16:50 +01:00
Stefano Babic
3e4d27b06d Merge git://git.denx.de/u-boot 2012-11-10 08:05:54 +01:00
Tom Rini
6acc7c3cbc Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-11-05 07:42:00 -07:00
Albert ARIBAUD
a42c87f9d8 Merge remote-tracking branch 'u-boot-ti/master' 2012-11-03 10:05:22 +01:00
Raphael Assenat
843a7ee8c4 eco5pk: Add new board and default config
Signed-off-by: Raphael Assenat <raph@8d.com>
[trini: Squash boards.cfg / MAINTAINERS change into main patch]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-30 15:28:06 -07:00
Pali Rohár
ed407be53e New board support: Nokia RX-51 aka N900
Based on previous work by: Alistair Buxton <a.j.buxton@gmail.com>

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Ивайло Димитров <freemangordon@abv.bg>
2012-10-30 15:28:06 -07:00
Lucas Stach
6bbda88384 tegra: add Colibri T20 board support
This adds board support for the Toradex Colibri T20 module.

Working functions:
- SD card boot
- USB boot
- Network
- NAND environment

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-29 09:07:04 -07:00
Wolfgang Denk
1b0757eced PPC: remove dead boards (AMX860, c2mon, ETX094, IAD210, LANTEC, SCM)
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years.  Get rid of the dead
weight.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
2012-10-28 20:17:25 +01:00
Stefano Babic
d81b27a245 MX35: add support for woodburn board
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.

The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash

In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:59 +02:00
Andrew Bradford
c3f8318f33 am335x_evm: Enable use of UART{1,2,3,4,5}
Add targets of am335x_evm_uart{1,2,3,4,5} to have serial input/output on
UART{1,2,3,4,5} for use with the Beaglebone RS232 cape, am335x_evm
daughterboard, and other custom configurations.

Modify target for am335x_evm to include SERIAL1 and CONS_INDEX=1
options in order to clarify UART selection requirements.

Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
2012-10-25 14:54:50 -07:00
Alison Wang
186fc4db26 ColdFire: Add Freescale MCF54418TWR ColdFire development board support
Add Freescale MCF54418TWR ColdFire development board support.

Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
2012-10-24 22:27:46 +08:00
Gerlando Falauto
c4d22de817 km83xx: add kmvect1 board
Add support for the new kmvect1 board powered by the mpc8309 processor.
As this board is very similar to the existing suvd3, instead of adding a
new config header file, just add a new config option to suvd3.h

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-10-23 15:23:26 -05:00
York Sun
ee52b188ca powerpc/t4qds: Add T4QDS board
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.

SERDES Connections
  32 lanes grouped into four 8-lane banks
  Two “front side” banks dedicated to Ethernet
  Two “back side” banks dedicated to other protocols
DDR Controllers
  Three independant 64-bit DDR3 controllers
  Supports rates up to 2133 MHz data-rate
  Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA

Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.

Detail information can be found in doc/README.t4qds

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 15:52:46 -05:00
Tom Rini
99070db0dc Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	drivers/serial/serial_lh7a40x.c

Signed-off-by: Tom Rini <trini@ti.com>
2012-10-19 18:23:38 -07:00
Paul Gortmaker
12c79a9578 powerpc: delete Wind River SBC8560/8540 support
The sbc8548/60 (both similar, just variations in UART hardware)
support has been removed from the linux kernel as of v3.6-rc1~132
so lets also now remove it from the u-boot tree as well.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-10-17 09:39:16 -07:00
Tom Rini
d1ff690612 Merge branch 'master' of git://git.denx.de/u-boot-mips 2012-10-17 08:57:13 -07:00
Stefan Roese
bfa5b71408 mpc82xx: Remove BMW board port
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: James F. Dougherty <jfd@broadcom.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2012-10-17 07:55:50 -07:00
Zhi-zhou Zhang
32afad783e MIPS: add board qemu-mips64 support
Both big-endian and little-endian are tested with below commands:
Rom version: (Default, Now we config it as rom version)
qemu-system-mips64el -M mips -bios u-boot.bin -cpu MIPS64R2-generic -nographic
qemu-system-mips64 -M mips -bios u-boot.bin -cpu MIPS64R2-generic -nographic
Ram version:
qemu-system-mips64el -M mips -cpu MIPS64R2-generic -kernel u-boot -nographic
qemu-system-mips64 -M mips -cpu MIPS64R2-generic -kernel u-boot -nographic

Signed-off-by: Zhizhou Zhang <etou.zh@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-10-16 15:02:08 +02:00