AXP818 supports VBUS drive function, even though the manual does not
mention it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS drive is supported on AXP221 and later PMICs. Rework the macros
so we can support this on later PMICs without too much work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
axp818_init() is declared, but never defined.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use a pointer to pass image address to fsl_secboot_validate(),
instead of using environmental variable "img_addr".
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case of fatal failure during secure boot execution (e.g. header
not found), reset is asserted to stop execution. If the RESET_REQ
is not tied to HRESET, this allows the execution to continue.
Add esbh_halt() after the reset to make sure execution stops.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For secure boot, currently we were using fixed bootargs for all SoCs.
This is not needed and we can use the bootargs which are used in
non-secure boot.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To unify steps for secure boot for xip (eg. NOR) and non-xip memories
(eg. NAND, SD), bootscipts and its header are copied to main memory.
Validation and execution are performed from there.
For other ARM Platforms (ls1043 and ls1020), to avoid disruption of
existing users, this copy step is not used for NOR boot.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sec_init has been called at the beginning to initialize SEC Block
(CAAM) which is used by secure boot validation later for both ls2080a
qds and rdb. 64-bit address in ESBC Header has been enabled. Secure
boot defconfigs are created for boards (NOR boot).
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For secure boot, a header is used to identify key table, signature
and image address. A new header structure is added for lsch3.
Currently key extension (IE) feature is not supported. Single key
feature is not supported. Keys must be in table format. Hence, SRK
(key table) must be present. Max key number has increase from 4 to
8. The 8th key is irrevocable. A new barker Code is used.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In LS2080, SFP has version 3.4. It is in little endian. The base
address is 0x01e80200. SFP is used in Secure Boot to read fuses.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The RPi3 typically uses the regular UART for high-speed communication with
the Bluetooth device, leaving us the mini UART to use for the serial
console. Add support for this UART so we can use it.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Some TI boards (e.g. IDK) have 4 to 6 ethernet ports and
this function is handy at board.c to configure the
MAC address of the ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, CONFIG_BCM2835 is defined for all BCM283x builds and _BCM2836
is defined when building for that SoC. That means there isn't a single
define that means "exactly BCM2835". This will complicate future patches
where BCM2835-vs-anything-else needs to be determined simply.
Modify the code to define one or the other of CONFIG_BCM2835/BCM2836 so
future patches are simpler.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have support for running with caches enabled in HYP mode,
opt in to that on the Raspberry Pi 2. This brings a significant performance
boost.
Signed-off-by: Alexander Graf <agraf@suse.de>
The EFI standard defines a simple boot protocol that an EFI payload can use
to access video output.
This patch adds support to expose exactly that one (and the mode already in
use) as possible graphical configuration to an EFI payload.
With this, I can successfully run grub2 with graphical output.
Signed-off-by: Alexander Graf <agraf@suse.de>
Same flash driver can be used by other stm32 families like stm32f7.
Better place for this driver would be mtd driver location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The description was borrowed from kernel. "tristate" type was changed
to "bool" (I believe we don't support modules for u-boot yet, right?).
CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along
as well.
Definitions were added to defconfig files in a way that
"make savedefconfig" generates exactly the same file as used defconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Add zynq_zc702 conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support for Altera StratixV bitstream programming. 2 FPGAs
are connected to the SPI busses. This patch uses board specific write
code to program the bitstream via SPI direct write mode.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for programming of the StratixV FPGAs. Programming
is done in this case (board theadorable) via SPI. The board may provide
board specific code for bitstream programming.
This StratixV support will be used by the theadorable board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 1e3d640316 (ARM: sheevaplug: redefine MTDPARTS) changed the partition
layout (without any description why), but didn't change the offset/size to
load the kernel from or the root=/dev/mtdblockX in the bootargs.
The 3MB forseen for a kernel is furthermore too little. A 4.4 build of
mvebu_v5_defconfig is 3.6MB:
-rw-r--r-- 1 peko peko 3.6M Jan 16 20:24 uImage.kirkwood-sheevaplug
When device tree support for sheevaplug was added to the kernel in commit
ee514b381e (ARM: Kirkwood: Add dts files for Sheevaplug and eSATA
Sheevaplug) a default flash partition layout (used if mtdparts= isn't passed
on the command line / CONFIG_MTD_CMDLINE_PARTS isn't enabled) with 1MB for
u-boot / environment, 4MB for the kernel and the rest for the rootfs, so use
that layout here and adjust the kernel loading to match.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable building of drivers/net/phy/realtek.c so that realtek phys
get properly initialized.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This commit syncs the dt-bindings/input/* headers with the kernel (v4.5)
and adds dt-bindings/clock/sun4i-a10-pll2.h, both are necessary for newer
sunxi dts files to build.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now everything is done to load a raw U-Boot proper image instead of
an mkimage-processed one (as far as I tested on NAND, eMMC, NOR).
The SPL already knows the load address of the U-Boot proper without
parsing its uImage header because the load address is defined by
CONFIG_SYS_TEXT_BASE, assuming that the two images are generated from
the same build.
My main motivation of this switch is to use u-boot-with-spl.bin, a
concatenation of u-boot-spl.bin and u-boot.bin. (I wish there were
a concatenation of u-boot-spl.bin and u-boot.img...) Anyway, this
commit would be useful for one-shot image burn.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This allows to boot from NOR flash (or SRAM) with help of an external
loader (NOR-loader).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too
long. It would not hurt to drop "PH1_" because "UNIPHIER_" already
well specifies the SoC family. Also, rename files for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This TODO is no longer useful. CONFIG_SYS_NS16550_SERIAL is just
ignored on DM serial.
If one wants to use the 16550A UART device on the UniPhier Micro
Support Card, it can be enabled by CONFIG_SYS_NS16550 via Kconfig.
Please notice CONFIG_SPL_OF_TRANSLATE must be enabled as well and
the device tree must be treaked in order to use the NS16550 serial
on SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Stephen Warren <swaren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
The license command isn't usually built and has a few problems:
- The rules to generate license.h haven't worked in a long time,
re-write these based on the bmp_logo.h rules.
- 'tok' is unused and the license text size has increased
- bin2header.c wasn't grabbing unistd.h to know the prototype for
read().
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
For Raspberry Pi, we had the input clock rate to the pl011 fixed in
the rpi.c file, but it may be changed by firmware due to user changes
to config.txt. Since the firmware always sets up the uart (default
115200 output unless the user changes it), we can just skip our own
uart init to simplify the boot process and more reliably get serial
output.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Some features are only useful or meaningful when the command line is
present. Ensure that these features are not compiled in when CONFIG_CMDLINE
is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
When CONFIG_CMDLINE is disabled we need to remove all the command-line
code. Most can be removed by dropping the appropriate linker lists from the
images, but sub-commands must be dealt with specially.
A simple mechanism is used to avoid 'unused static function' errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
After power cycle of a K2G EVM dhcp fails due to a auto-negotiation
timeout. This commit increases the timeout to fix the issue.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_CONSOLE_IS_IN_ENV needs to be enabled, so we could set stdout
environment variable to specify the vga for the console output when
LCD/HDMI is connected to the boards.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Put pci_get_hose_head() prototype in header so it is available to
external users, allowing them to find and iterate over all pci
controllers.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To use AQR405 PHY's interrupt, we need to invert the relative IRQ pins
polarity by setting IRQCR register, because AQR405 interrupt is low
active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch makes the following changes to the SR1500 board port:
- Update defconfig to support SPI NOR (use make savedefconfig).
- Increase SPI speed to a maximum of 100MHz for faster system
bootup.
- Change environment location, so that its not between SPL and
main U-Boot. This way the combined SPL / U-Boot image can
be used for updates.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
This patch makes it possible that boards can define a board-specific env
size. This is used by the SR1500 SoCFPGA board port.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Marek Vasut <marex@denx.de>
Move the inclusion of the common socfpga configuration file further
down in the sr1500 configuration, so that the socfpga_common.h can
check if environment is in SPI NOR and it's location is defined and
if it is not, define default location.
This fixes "arm: socfpga: Enabling U-Boot environment support in QSPI"
which introduced a minor warning.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling the support of storing U-Boot environment
within serial NOR flash. By default, its still
store into SDMMC
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
This patch changes the USB port scanning procedure and timeout
handling in the following ways:
a)
The power-on delay in usb_hub_power_on() is now reduced to a value of
max(100ms, "hub->desc.bPwrOn2PwrGood * 2"). The code does not wait
using mdelay, instead usb_hub_power_on() will wait before querying
the device in the scanning loop later. The total timeout for this
hub, which is 1 second + "hub->desc.bPwrOn2PwrGood * 2" is calculated
and will be used in the following per-port scanning loop as the timeout
to detect active USB devices on this hub.
b)
Don't delay the minimum delay (for power to stabilize) in
usb_hub_power_on(). Instead skip querying these devices in the scannig
loop until the delay time is reached.
c)
The ports are now scanned in a quasi parallel way. The current code did
wait for each (unconnected) port to reach its timeout and only then
continue with the next port. This patch now changes this to scan all
ports of all USB hubs quasi simultaneously. For this, all ports are added
to a scanning list. This list is scanned until all ports are ready
by either a) reaching the connection timeout (calculated earlier), or
by b) detecting a USB device. This results in a faster USB scan time as
the recursive scanning of USB hubs connected to the hub that's currently
being scanned will start earlier.
One small functional change to the original code is, that ports with
overcurrent detection will now get rescanned multiple times
(PORT_OVERCURRENT_MAX_SCAN_COUNT).
Without this patch:
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 20.163 seconds
With this patch:
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 1.822 seconds
So ~18.3 seconds of USB scanning time reduction.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Moved the new field to the end of the struct to avoid problems:
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for the congatec conga-QA3/E3845-4G eMMC8 SoM,
installed on the congatec Qseven 2.0 evaluation carrier board
(conga-QEVAL).
Its port is very similar to the MinnowboardMAX port and also uses
the Intel FSP as described in doc/README.x86.
Currently supported are the following interfaces / devices:
- UART (via Winbond legacy SuperIO chip on carrier board)
- Ethernet (PCIe Intel I210 / E1000)
- SPI including SPI NOR as boot-device
- USB 2.0
- SATA via U-Boot SCSI IF
- eMMC
- Video (HDMI output @ 800x600)
- PCIe
Not supported yet is:
- I2C
- USB 3.0
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds basic support for chromebook_samus. This is the 2015 Pixel and
is based on an Intel broadwell platform.
Supported so far are:
- Serial
- SPI flash
- SDRAM init (with MRC cache)
- SATA
- Video (on the internal LCD panel)
- Keyboard
Various less-visible drivers are provided to make the above work (e.g. PCH,
power control and LPC).
The platform requires various binary blobs which are documented in the
README. The major missing feature is USB3 since the existing U-Boot support
does not work correctly with Intel XHCI controllers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is not needed now that the memory controller driver has the SPD data
in its own node.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is an extra line in the comment in the header. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is a little easier on the eyes, particularly when the backlight is set
to maximum.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an address which can be used for loading and running the reference code
when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GPIO pins need to be set up on start-up. Add a driver to provide this,
configured from the device tree.
The binding is slightly different from the existing ICH6 binding, since that
is quite verbose. The new binding should be just as extensible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
We don't need this anymore - we can use device tree and the new pinconfig
driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add one more step into the init sequence. This fixes the keyboard on samus,
which otherwise does not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Two comments are missing a parameter and there is an extra blank line. Also
two of the region access macros are misnamed. Correct these problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is common to read a config register value, clear and set some bits, then
write back the updated value. Add functions to do this in one step, for
convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some functions do not change the struct gpio_desc parameter. Update these to
use const so this is clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We can use GPIOs as binary digits for reading 'strapping' values. Each GPIO
is assigned a single bit and can be set high or low on the circuit board. We
already have a legacy function for reading these values. Add one that
supports driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some CPUs use microcode and each core can have a different version of
microcode loaded. Also some CPUs support the concept of an integer ID used
for identification purposes. Add support for these in the CPU uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
NFS loading is similar to net loading except initial files are loaded
over NFS instead of TFTP, this removes the need for multiple different
protocol servers running on the host and allows the use of a single
network file system containing boot related files in their usual
in-filesystem directory. Add defaults for this boot style here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For k2l, k2e and k2hk, ubi is set to default boot in uboot
environment settings; while for k2g, mmc should be the
default boot. This patch is to set mmc as default for k2g-evm
Signed-off-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch updates the env script to include a initramfs with firmware
loaded and provided to kernel through second argument of bootz command
during boot. Defined DEFAULT_FW_INITRAMFS_BOOT_ENV to have all of the
required env variables and use it in evm specific config file.
The K2 linux drivers for PCIe and NetCP (1G, 10G) requires serdes
firmwares. These requires firmware to be available early through the boot
process in some cases to satisfy firmware requests from driver. Hence use
a small initramfs to provide the same and update boot env to accommodate
this in the boot flow. This method is used when rootfs is nfs and ubifs.
This fs contains just lib/firmware folder with all required firmware.
When rootfs is on initramfs, then the filesystem has the firmware under
lib/firmware and this early initramfs is not required and is not used.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding support to save env in MMC on k2g platforms, as it is the
preferred peripheral in saving env.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For development purposes, it is easier to use the env import command
and plain text or script files instead of script-images. So allow
u-boot to load env var from a text file or a script file.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Support for loading bootscript and text env file is duplicated in all TI
platforms. Add this information to DEFAULT_MMC_TI_ARGS so that it can be
reused in all TI platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With commit aee119bd70 ('am43xx_evm: add usb host boot support') usb
commands is removed from U-boot second stage and enbaled only on USB
boot config. Fixing this by enable USB commands for both USB boot and
in second stage u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_SPL_NET_VCI_STRING is available only with BOOTP. So if
CMD_DHCP is enabled for SPL in usb ether boot, it will not pass
the right vendor name and failing to download the right file.
Also all the net CMD_* are not required in SPL builds. So defining
these only for non-SPL builds.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
securedb.key.bin is not supported so it should not be loaded by
default init_ubi command.
Signed-off-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
UBI images created by OE does not contain boot partition by default,
instead kernel and dtb are placed in /boot directory inside rootfs
partition. So update env commands to load files from correct
location.
Signed-off-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add USB mass storage support so that kernel can be read from
connected usb storage.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
EFI payloads can query for the device they were booted from. Because
we have a disconnect between loading binaries and running binaries,
we passed in a dummy device path so far.
Unfortunately that breaks grub2's logic to find its configuration
file from the same device it was booted from.
This patch adds logic to have the "load" command call into our efi
code to set the device path to the one we last loaded a binary from.
With this grub2 properly detects where we got booted from and can
find its configuration file, even when searching by-partition.
Signed-off-by: Alexander Graf <agraf@suse.de>
The commonly defined environment variable to determine the device tree
file name is called fdtfile rather than fdt_name. Replace all occurences
of fdt_name with fdtfile.
Signed-off-by: Alexander Graf <agraf@suse.de>
UEFI defines a simple boot protocol for removable media. There we should look
at the EFI (first GPT FAT) partition and search for /efi/boot/bootXXX.efi with
XXX being different between different platforms (x86, x64, arm, aa64, ...).
This patch implements a simple version of that protocol for the default distro
boot script. With this we can automatically boot from valid UEFI enabled
removable media.
Because from all I could see U-Boot by default doesn't deliver device tree
blobs with its firmware, we also need to load the dtb from somewhere. Traverse
the same EFI partition for an fdt file that fits our current board so that
an OS receives a valid device tree when booted automatically.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EFI loader needs to maintain views of memory - general system memory
windows as well as used locations inside those and potential runtime service
MMIO windows.
To manage all of these, add a few helpers that maintain an internal
representation of the map the similar to how the EFI API later on reports
it to the application.
For allocations, the scheme is very simple. We basically allow allocations
to replace chunks of previously done maps, so that a new LOADER_DATA
allocation for example can remove a piece of the RAM map. When no specific
address is given, we just take the highest possible address in the lowest
RAM map that fits the allocation size.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Simon Glass <sjg@chromium.org>
A EFI applications usually want to access storage devices to load data from.
This patch adds support for EFI disk interfaces. It loops through all block
storage interfaces known to U-Boot and creates an EFI object for each existing
one. EFI applications can then through these objects call U-Boot's read and
write functions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
[trini: Update for various DM changes since posting]
Signed-off-by: Tom Rini <trini@konsulko.com>
After booting has finished, EFI allows firmware to still interact with the OS
using the "runtime services". These callbacks live in a separate address space,
since they are available long after U-Boot has been overwritten by the OS.
This patch adds enough framework for arbitrary code inside of U-Boot to become
a runtime service with the right section attributes set. For now, we don't make
use of it yet though.
We could maybe in the future map U-boot environment variables to EFI variables
here.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
One of the basic EFI interfaces is the console interface. Using it an EFI
application can interface with the user. This patch implements an EFI console
interface using getc() and putc().
Today, we only implement text based consoles. We also convert the EFI Unicode
characters to UTF-8 on the fly, hoping that everyone managed to jump on the
train by now.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
When an EFI application runs, it has access to a few descriptor and callback
tables to instruct the EFI compliant firmware to do things for it. The bulk
of those interfaces are "boot time services". They handle all object management,
and memory allocation.
This patch adds support for the boot time services and also exposes a system
table, which is the point of entry descriptor table for EFI payloads.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
EFI uses the PE binary format for its application images. Add support to EFI PE
binaries as well as all necessary bits for the "EFI image loader" interfaces.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The EFI API header is great, but missing a good chunk of function prototype,
GUID defines and enum declarations.
This patch extends it to cover more of the EFI API. It's still not 100%
complete, but sufficient enough for our EFI payload interface.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
We have a pretty nice and generic interface to ask for a specific block
device. However, that one is still based around the magic notion that
we know the driver name.
In order to be able to write fully generic disk access code, expose the
currently internal list to other source files so that they can scan through
all available block drivers.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>