- Initialize PLLs (SPL initializes only DPLL to save the precious
SPL memory footprint)
- Adjust CPLL/MPLL to the final tape-out frequency
- Set the Cortex-A53 clock to the maximum frequency since it is
running at 500MHz (SPLL/4) on startup
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Initialize the DPLL (PLL for DRAM) in SPL, and others in U-Boot
proper. Split the common code into pll-base-ld20.c for easier
re-use.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The PLL for the DRAM interface must be initialized in SPL, but the
others can be delayed until U-Boot proper. Move them from SPL to
U-Boot proper to save the precious SPL memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the last code in the mach-uniphier/pinctrl/ directory.
Push the remaining code out to delete the directory entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the pin-mux data in the pinctrl drivers by directly calling
pinctrl_generic_set_state().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The NAND subsystem has not supported the Driver Model yet, but the
NAND pin-mux data are already in the pinctrl drivers. Use them by
calling pinctrl_generic_set_state() directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Unfortunately, this SoC needs per-board adjustment between clock
and address/command lines. This flag will be passed to the DRAM
init function and used for compensating the difference of DRAM
timing parameters.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the UniPhier platform calls several init functions in the
following order:
[1] spl_board_init()
[2] board_early_init_f()
[3] board_init()
[4] board_early_init_r()
[5] board_late_init()
The serial console is not ready at the point of [2], so we want to
avoid using [2] from the view point of debuggability. Fortunately,
all of the initialization in [2] can be delayed until [3]. I see no
good reason to split into [3] and [4]. So, merge [2] through [4].
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I need to add more board attributes, so the "flags" member will be
handier than separate boolean ones.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The code in uniphier_sld3_sbc_init() is pin-muxing, so it would
be a better fit in uniphier_sld3_early_pin_init().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The System Bus is not available by default on the ROM boot mode of
PH1-LD20. To use devices connected to the System Bus, such as the
Micro Support Card, it is necessary to set up pin-muxing and some
System Bus Controller register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Eliminate the "ph1"_ prefixes from function names because "uniphier_"
describes the SoC familiy better.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is a bunch of duplication in the System Bus Controller init
code. Roughly, there are two types in the SBC mode: Adress/Data
Multiplex Mode and Save Pins Mode. Consolidate per-SoC functions
into the two, plus per-SoC optional init code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a field to distinguish DDR3+ from (standard) DDR3. It also
allows to delete CONFIG_DDR_STANDARD (this is not a software
configuration, but a board attribute).
Default DDR3 spec for each SoC:
PH1-LD4, PH1-sLD8: DDR3+
Others: DDR3
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This commit reworks "struct uniphier_board_data" with an array of
DRAM channel data in it. It will allow further cleanups by means of
"for" statements that iterate over the DDR channels.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As mentioned in the log of commit 019df879a9 (ARM: uniphier: add
ProXstream2 and PH1-LD6b support), the DRAM init code was missing
for a long time. Finally, here it is. SPL works now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These headers are only included locally in arch/arm/mach-uniphier/.
There is no reason to export them by putting in the mach/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
