The patch is referred to at91 clock driver of Linux, to make
the clock node descriptions in DT aligned with the Linux's.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Linux stopped the use of keyword 'boolean' in Kconfig.
Refer to commit 6341e62b212a2541efb0160c470e90bd226d5496 ("kconfig:
use bool instead of boolean for type definition attributes")
in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a node for evm_3v3_sd using onboard PCF GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Create drivers/sysreset and move sysreset-uclass and all sysreset
drivers there.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Flush operations need to be cacheline aligned to take effect, make
sure to flush always complete cachelines. This avoids messages such
as:
CACHE: Misaligned operation at range [00900000, 009004d9]
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
This outer cache allows to control active ways independently for
each CPU, so this function will be useful to set up active ways
for a specific CPU.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move this option to Kconfig, renaming it into CONFIG_CACHE_UNIPHIER.
The new option name makes sense enough, and the same as Linux has.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, all of these macros are only used in cache-uniphier.c, so
there is no need to export them in a header file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DRAM is available at this point, so setup the temporary stack
and call the C function to reduce the code duplication a bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The System Cache (outer cache) is used not only as L2 cache,
but also as locked SRAM. The functions for turning on/off it
is necessary whether the L2 cache is enabled or not.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As the sLD3 Boot ROM has a complex page table, it is difficult to
set up the debug UART with enabling it. It will be much easier to
initialize the UART port after switching over to the straight-mapped
page table.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 4b50369fb5 ("ARM: uniphier: create early page table at
run-time") broke the ROM boot mode for PH1-sLD3 SoC, because the
run-time page table creation requires the outer cache register
access but the page table in the sLD3 Boot ROM does not straight-map
virtual/physical addresses.
The idea here is to check the current page table to determine if
it is a straight map table. If not, adjust the outer cache register
base.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Here, the ldr pseudo-instruction falls into the ldr + data set.
The register access by [r1, #offset] produces shorter code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_UNIPHIER_L2CACHE_ON is undefined, the L2 cache is never
enabled, so there is no need for v7_outer_cache_disable(). The weak
stub avoids the compile error anyway.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The UniPhier outer cache (L2 cache on ARMv7 SoCs) can be used as
SRAM by locking ways.
These functions will be used to transfer the trampoline code for SMP
into the locked SRAM.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Unify the range/all operation routines into the common function,
uniphier_cache_maint_common(), and sync code with Linux a bit more.
This reduces the code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit "ecc3066 Fix board init code to respect the C runtime environment"
broke platform support for ppc4xx.
start.S prepares a stackframe that is later rendered unusable by appending
the reserved space for global data.
Instead the reserved space has to be put first. Then the stackframe can
be pushed.
I can only test the 405EP OCM case. At least all other ppc4xx boards still
build.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate mode-gpios DT entry so that driver can select the required
slave.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-len
with 0 in PCF8575 DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We create 2 sets of page tables: One for normal operation, one for
emergency (used while modifying the former).
Because the page tables grow dynamically, we have code that checks
for overflow. Unfortunately we didn't adjust the available space
variable while creating the emergency tables, so potentially someone
might run into an overflow there (not seen in real world yet though!).
Fix it by properly adjusting the size as well as the base offset in
emergency page table creation.
Reported-by: York Sun <york.sun@nxp.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features. At this point in time they no longer serve a good purpose so
remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
rk3399 sdcard is using dwmmc controller, enable it for sdcard.
SCLK_SDMMC is the clock for controller operation clock, move it
to the first place.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add an extra byte so that this data is not byteswapped.
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the case of omap3 we have a number of platforms that are close to
exceeding SRAM limits, depending on compiler. Move to USE_TINY_PRINTF
to give them more room. OMAP4 will soon enough be in a similar place,
so enable that now.
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of testing booting Linux kernels on Rockchip devices, it was
discovered by Ziyuan Xu and Sandy Patterson that we had multiple and for
some cases incomplete isb definitions. This was causing a failure to
boot of the Linux kernel.
In order to solve this problem as well as cover any corner cases that we
may also have had a number of changes are made in order to consolidate
things. First, <asm/barriers.h> now becomes the source of isb/dsb/dmb
definitions. This however introduces another complexity. Due to
needing to build SPL for 32bit tegra with -march=armv4 we need to borrow
the __LINUX_ARM_ARCH__ logic from the Linux Kernel in a more complete
form. Move this from arch/arm/lib/Makefile to arch/arm/Makefile and add
a comment about it. Now that we can always know what the target CPU is
capable off we can get always do the correct thing for the barrier. The
final part of this is that need to be consistent everywhere and call
isb()/dsb()/dmb() and NOT call ISB/DSB/DMB in some cases and the
function names in others.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Sandy Patterson <apatterson@sightlogix.com>
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reported-by: Sandy Patterson <apatterson@sightlogix.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As of now we have 2 flavors of ARC SDP boards:
1) AXS101 - with ARC770 in ASIC
2) AXS103 - with ARC HS38 in FPGA
Both options share exactly the same base-board and only differ with
CPU-tiles in use. That means all peripherals are the same (they are
implemented in FPGA on the base-board) and so generic board could be
used for both.
While at it:
* Recreated defconfigs with savedefconfig
* In include/configs/axs10x.h numerical sizes replaced with
defines from linux/sizes.h for better readability.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ARCangel was one of the main development boards back in the day but
now it's gone and replaced by other boards like ARC SDP.
But we also used to have simulation platform very similar to ARCangel4
in terms of CPU settings as well as basic IO like UART. Even though
ARCangel4 is long gone now we have a replacement for simulation which is
a plain or stand-alone nSIM and Free nSIM.
Note Free nSIM is available for download here:
https://www.synopsys.com/cgi-bin/dwarcnsim/req1.cgi
And while at it:
* Finally switch hex numerical values in nsim.h to defines from
include/linux/sizes.h
* Add defconfigs with ARC HS38 cores
* Recreated all defconfigs with savedefconfig
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Starting from arc-2016.03 GNU tools linker properly works with
symbols defined in linker script and so external declarations
are no longer required, dump them.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Initially IVT for ARCv2 was simply copypasted from ARCompact
with some selected fixes so basic stuff works.
Now we update it with more ARCv2 specific vectors like
* Software Interrupt
* Division by zero
* Data cache consistency error
* Misaligned access
Also normal interrupts are now implemented properly and extened to
all possible 240 items.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This might be useful to make sure relocation fixups really
happen. And since this info gets printed only in DEBUG
build it doesn't really hurt normal execution.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Introduce tegra_board_init() and call it from board_init(). Tegra wil use
tegra_board_init() for board-specific initialization, and board_init() for
SoC-specific initialization.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 has 8 I2C controllers including BPMP I2C. This patch adds the
other 7 generic controllers to Tegra186's DT.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, fixed DT node sort order, tweak patch description)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra186 PCIe DT content is almost identical to previous chips, except
that the:
- There are 3 ports instead of 2.
- Some physical addresses have moved.
- PHY programming is handled by firmware, so CCPLEX DTs don't need to
reference any PHY.
- The power domain is explicitly represented in DT. This change is
mandatory for Tegra186 since standard power domain APIs are used, and
should be made to the DT for older SoCs, although we get away without
doing so since U-Boot currently uses custom APIs that hard-code power
domain IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This allows the BPMP I2C device to be instantiated, which makes it
available to other drivers and the user.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds the DT content that's needed to allow board DTs to enable use
of BPMP, clocks, resets, GPIOs, eMMC, and SD cards.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The DT binding for the Tegra186 HSP module apparently wasn't quite final
when I posted initial U-Boot support for it. Add the final DT binding doc
and adapt all code and DT files to match it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
