Fix the problem that cannot access actual data when CPU data cache enabled.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
cs8900.c: In function 'eth_init':
cs8900.c:164: warning: passing argument 2 of 'eth_getenv_enetaddr' from incompatible pointer type
cs8900.c:165: error: invalid operands to binary <<
cs8900.c:166: error: invalid operands to binary <<
cs8900.c:167: error: invalid operands to binary <<
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Also, do not bother checking the EEPROM if the env is setup. This
simplifies the code greatly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Dnek <wd@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Rolf Offermanns <rof@sysgo.de>
CC: Erik Stahlman <erik@vt.edu>
CC: Daris A Nevil <dnevil@snmc.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The sh_eth driver can also be simplified a bit by using enetaddr member of
the eth_device structure.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Carlos Munoz <carlos@kenati.com>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The cs8900 driver also changes slightly in that the hardware is not
consulted if the mac address in the env is sane.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Marius Groeger <mgroeger@sysgo.de>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Since the address is in the PLM_DEVICE_BLOCK structure already, there is
no need to pass the NodeAddress as a second parameter. So drop the second
argument to the LM_SetMacAddress() function (and update the tigon3 driver
accordingly).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The drivers that get converted here:
3c589
4xx_enet
dc2114x
dm9000x
enc28j60
fsl_mcdmafec
ks8695eth
mcffec
rtl8019
rtl8169
s3c4510b_eth
xilinx_emac
xilinx_emaclite
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Rolf Offermanns <rof@sysgo.de>
CC: Stefan Roese <sr@denx.de>
CC: Sascha Hauer <saschahauer@web.de>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
CC: Greg Ungerer <greg.ungerer@opengear.com>
CC: Xue Ligong <lgxue@hotmail.com>
CC: Masami Komiya <mkomiya@sonare.it>
CC: Curt Brune <curt@cucy.com>
CC: Michal SIMEK <monstr@monstr.eu>
Since the on-chip MAC does not have an eeprom or similar interface, force
all Blackfin boards that use this driver to setup the board data with a
proper MAC.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
sh_eth_reset is function to reset Ether IP.
The MAC address is stored in IP, but it is initialized by this function.
OS (e.g. Linux Kernel) can not use this device when initialized.
This revises this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Commit af1c2b84 added a generic phy support, with an ID of zero
and a 32 bit mask; meaning that it will match on any PHY ID.
The problem is that there is a test that checked if a matching
PHY was found, and if not, it printed the non-matching ID.
But since there will always be a match (on the generic PHY,
worst case), this test will never trip.
In the case of a misconfigured PHY address, or of a PHY that
isn't explicitly supported outside of the generic support,
you will never see the ID of 0xffffffff, or the ID of the
real (but unsupported) chip. It will silently fall through
onto the generic support.
This change makes that test useful again, and ensures that
the selection of generic PHY support doesn't happen without
some sort of notice. It also makes it explicitly clear that
the generic PHY must be last in the PHY table.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The smc911x driver has a lot of useful defines/functions which can be used
by pieces of code (such as example eeprom programmers). Rather than
forcing each place to duplicate these defines/functions, split them out
of the smdc911x driver into a local header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Guennadi Liakhovetski <lg@denx.de>
CC: Magnus Lilja <lilja.magnus@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
Added the struct containing PHY settings for the Vitesse VSC8211 phy to
the phy_info list in tsec.c
Signed-off-by: Pieter Henning <phenning@vastech.co.za>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added new CONFIG options for the three type of MAC-PHY interconnect and
applied them all relevant board config files
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
SOFT_RESET must be asserted for at least 3 TX clocks. Usually, that's about 30
clock cycles, so it's been mostly working. But we had no guarantee, and at
slower bitrates, it's just over a microsecond (over 1000 clock cycles). This
enforces a 2 microsecond gap between assertion and deassertion.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
100Mbs ethernet does not work on sh7763 chips due to the wrong value being
used in the GECMR register. Following diff fixes the problem
Signed-off-by: Simon Munton <simon@nidoran.m5data.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Driver for Dave DNET ethernet controller (used on Dave/DENX
QongEVB-LITE board).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Modified mii_init to support boards with PHYs that are not set to
autonegotiate, but still want to use u-boot's mii commands to probe
the smi bus. Such PHYs will not set the Autonegotiate-done bit.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Redo how pointers are managed to get rid of ugly casts and strict pointer
aliasing issues that are highlighted by gcc 4.3.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
No point in having a Blackfin-specific define "CONFIG_BFIN_MAC_RMII" that
does exactly the same thing as common "CONFIG_RMII".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather then defining our own DEBUGF(), just use the common debug().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather than having the on-chip MAC hardcoded to phy address 1 and a speed
of 2.5mhz, use these as defaults if the board doesn't specify otherwise.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Cleanup and rewrite the MII/PHY related functions so that we can reuse the
existing common linux/miiphy.h code and hook into the `mii` command.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather than hardcoding MDCDIV to 24 (which is correct for ~125mhz SCLK),
use the real algorithm so it gets set correctly regardless of SCLK.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds support for searching through available PHY-addresses in
the macb-driver. This is needed for the ATEVK1100 evaluation board,
where the PHY-address will be initialized to either 1 or 7.
This patch adds a config option, CONFIG_MACB_SEARCH_PHY, which when
enabled tells the driver to search for the PHY address.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adjusts the LED control so that interrupt lines are not reading LEDs
and effectively causing indefinite interrupts to the controller.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
sh_eth used old network API. This patch changed new API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch changes the reg_read/_write to smc911x_reg_read/_write
and defines then as weak so that they can be overridden by board
specific version.
This will be used by the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch tries to ensure that phy interrupt pin
won't be asserted after booting. We experienced
following issues with current 88E1121R phy init:
Marvell 88E1121R phy can be hardware-configured
to share MDC/MDIO and interrupt pins for both ports
P0 and P1 (e.g. as configured on socrates board).
Port 0 interrupt pin will be shared by both ports
in such configuration. After booting Linux and
configuring eth0 interface, port 0 phy interrupts
are enabled. After rebooting without proper eth0
interface shutdown port 0 phy interrupts remain
enabled so any change on port 0 (link status, etc.)
cause assertion of the interrupt. Now booting Linux
and configuring eth1 interface will cause permanent
phy interrupt storm as the registered phy 1 interrupt
handler doesn't acknowledge phy 0 interrupts. This
of course should be fixed in Linux driver too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All CF platforms' mii.c are consolidated into one
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Also changed path in all linker scripts that reference this driver
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Patch to fix buffer allocation size and alignment. Buffer needs to be u32 aligned and
PKTSIZE_ALIGN bytes long.
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Currently VSC8601 doesn't link with 10/100M partners if the
EEPROM/Strapping is not set up.
Setting the auto-neg register fixes this.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
get_prom function was used __attriute__ , but it is not enable.
ax88796.o does not do link besides ne2000.o. When ld is carried
out, get_prom function of ax88796.c is ignored.
This problem is a thing by specifications of ld.
I checked and test this patch on SuperH and MIPS.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Fix TBI PHY accesses to use the proper offset in CPU register space. The
previous code would incorrectly access the TBI PHY by reading/writing to CPU
register space at the same location as would be used to access external PHYs.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
