The STGEN is the clock source for the Cortex A7 arch timer.
So after modification of its frequency, CP15 cntfreq is updated
and a new timer init is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The patch set dpll settings for 300MHz to values used by binary
blob[1]. With new values dpll still generate 300MHz clock, but
EMAC work. Probably with new values dpll generate more stable clock.
dpll on rk3188 provide clocks to DDR and EMAC. With current
dpll settings EMAC doesn't work on radxa rock. EMAC sends packets
to network, but it doesn't receive anything. ifconfig shows a lot
of framing errors.
[1] https://github.com/linux-rockchip/u-boot-rockchip/blob/u-boot-rk3288/
tools/rk_tools/3188_LPDDR2_300MHz_DDR3_300MHz_20130830.bin
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch print pl clocks (pl0...pl3) and watchdog
clock using clk dump.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
watchdog clock is also connected to cpu 1X clocksource.
Zynq> clk dump
...
Before:
swdt 4294967290
After:
swdt 111111110
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add RCC clock driver for STMP32MP157
- base on driver model = UCLASS_CLK
- support ops to enable, disable and get rate
of all SOC clock needed by U-Boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As said in the SAMA5D2 datasheet, the PLLA clock must be divided
by 2 by writing the PLLADIV2 bit in PMC_MCKR, if the ratio between
PCK and MCK is 3 (MDIV = 3). This is the purpose of the driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add USB clock driver to configure the input clock and the divider
in the PMC_USB register to generate a 48MHz and a 12MHz signal to
the USB Host OHCI.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
DSI clock is available on STM32F769-disco and
STM32F469-disco board.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Implement set_rate() for LTDC clock only, set_rate for other
clocks will be added if needed. This is needed by future LTDC driver
improvements.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Configure SAI PLL configuration to generate LTDC pixel clock on
the PLLSAIR output.
PLLSAI is enabled only if CONFIG_VIDEO_STM32 flag is set.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Rework the way SDMMC clock get rate is done in a more
generic way :
_ Add stm32_clk_get_pllsai_rate() which give the PLLSAI
indicated output rate.
_ Add stm32_clk_get_pllsai_vco_rate() which give the VCO
internal rate.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Initially, 48Mhz for SDIO clock was generated from SAI pll for
STM32F469 and STM32F746 SoCs, but this solution was not suitable
for STM32F429 SoCs.
A generic solution is to used the PLL_Q output as 48Mhz clock
for all STM32F SOCs family.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Wrong parameter was passed to stm32_clk_pll48clk_rate().
sysclk (PLL_p output value) was passed instead of VCO value.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The device-tree node for the PMU clk controller assigns to its parent
(i.e. PLL_PPLL) even though this clock currently is set up statically
by an init-function.
In order to avoid unexpected failures, a simple implementation of
set_rate (which accepts requests, but notifies the caller of the
preset frequency in its return value) and get_rate (which always
returns the preset frequency) are added.
Note that this is required for the RK808 PMIC to probe successfully on
the RK3399-Q7, following the support for the assigned-clocks property.
References: commit f4fcba5c5b ("clk: implement clk_set_defaults()")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Since commit ba1f966725 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3368 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.
This change extends the RK3368 clk driver to:
(a) provide a enable op
(b) signals success to the caller when the clocks for the GMAC are
enabled (no actual action is necessary as the gates are open
after reset)
References: commit ba1f966725 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Since commit ba1f966725 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3399 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.
This change extends the enable-op of the rk3399 clk driver to signal
success to the caller when the clocks for the GMAC are enabled.
References: commit ba1f966725 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The SD driver calls clk_set_rate() before clk_enable(), yet clk_set_rate()
implementation in the clock driver does not set the SD-IF divider. Fix it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since 'commit f4fcba5c5b ("clk: implement clk_set_defaults()")'
STM32F4 family board can't boot.
Above patch calls clk_set_rate() for all nodes with assigned-clock-rates
property. Clock driver for STM32F family doesn't implement .set_rate
callback which make clk_set_defaults() exit on error and prevent board
to boot.
Fixes: f4fcba5c5b ("clk: implement clk_set_defaults()")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The set_parent implementations do not make sense when OF_PLATDATA is
enabled. We guard these against OF_PLATDATA and don't populate the
set_parent-op when this is the case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Implement the setting parent for gmac clock, and add internal
pll div set for mac clk.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3288 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3288 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
implement the gmac clock set parent, but simply ignore the
others' set_rate() operation and return 0 to signal success.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Assuming mac_clk is fed by an external clock, set clk_rmii_src
clock select control register from IO for rgmii interface.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The rk3328 soc has two gmac controllers, one is gmac2io,
the other is gmac2phy. We use the gmac2io rgmii interface
for 1000M phy here.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3399 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3399 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
simply ignore the set_rate() operation and return 0 to signal success.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Linux uses the properties 'assigned-clocks', 'assigned-clock-parents'
and 'assigned-clock-rates' to configure the clock subsystem for use
with various peripheral nodes.
This implements clk_set_defaults() and hooks it up with the general
device probibin in drivers/core/device.c: when a new device is probed,
clk_set_defaults() will be called for it and will process the
properties mentioned above.
Note that this functionality is designed to fail gracefully (i.e. if a
clock-driver does not implement set_parent(), we simply accept this
and ignore the error) as not to break existing board-support.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Series-version: 2
Cover-letter:
clk: support assigned-clock, assigned-clock-parents, assigned-clock-rates
For various peripherals on Rockchip SoCs (e.g. for the Ethernet GMAC),
the parent-clock needs to be set via the DTS. This adds the required
plumbing and implements the GMAC case for the RK3399.
END
This implements the (newly added) set_parent() operation for the
RK3399 with a focus on allowing the RGMII clock parent to be
configured via the assigned-clock-parents property of the GMAC node.
This implementation supports only the GMAC (in fact only the RGMII
clock parent) and allows to set this clock's parent either to the
internal SCLK_GMAC or to an external clock input (identifiable by it
providing a 'clock-output-name' of "gmac_clkin").
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
The logic in clk_get_by_index() may be useful for other properties
than 'clocks': e.g. 'assigned-clocks' and 'assigned-clock-parents'
follows the same model.
This commit refactors clk_get_by_index() by introducing an internal
function clk_get_by_indexed_prop() that allows to specify the name
of the property to process. The original clk_get_by_index() call
is simply directed through this helper function with the property
name fixed to "clocks".
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Clocks may support multiple parents: this change introduces an
optional operation on the clk-uclass to set a clock's parent.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
PLLSAIP divider uses 2 bits (bits 16 and 17) into RCC_PLLSAICFGR
register, available combination are :
00: PLLSAIP = 2
01: PLLSAIP = 4
10: PLLSAIP = 6
11: PLLSAIP = 8
Previously, the divider value was incorrectly set to 6.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.
As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.
Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Thanks to 'commit ba1f966725 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
All current STM32F4 supported boards uses a 8MHz external oscillator.
All current STM32F7 supported boards uses a 25MHz external oscillator.
In order to introduce the new stm32f429-evaluation board which uses a
25MHz external oscillator without creating a dedicated struct
stm32_clk_info for this board, retrieve the external oscillator
frequency from DT and set pll_m accordingly to obtain 1MHz for the VCO.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add macros for the DIV6P1 clock type, which is used on Gen2
and optionally also on Gen3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull code which is common for RCar Gen2 and RCar Gen3 into
separate source file. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entries for each SoC clock table, so they can be
compiled in or out at build time. This can reduce the size of
the binary if desired.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Gen2 requires setting RMSTPCR before booting, while on Gen3 this
is thus far always zero. Split the tables so the RMSTPCR can be set
too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Extract the macros specific to Gen3 clock into a separate header.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all SoCs have the same PLL configuration options,
so make those PLL configuraion tables per-SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all drivers use the same IDs, so make those IDs per-driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Split the massive driver into smaller per-SoC drivers and pull the
common code into a separate file. This would allow configuring out
unnecessary clock drivers once the Kconfig changes are in and also
allow adding more clock tables easily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Makefile entries in the clk driver directory were not alphabetically
sorted. Correct this.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The clk uclass was converted to support a live device tree recently,
hence the global data pointer declarations are no longer needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
checkpatch.pl complains that the clk_ops structures used in clk-uclass.c
ought to be const, so we mark them as const.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Update default AXI, TUN, ARC clock set options:
instead of changing only IDIV divider settings adjust also domain PLL
settings.
Add support of TUN_ROM and TUN_PWM clocks (subclocks of TUNN_PLL)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.
Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.
Enable also CLK flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Bind rockchip reset to clock-controller with rockchip_reset_bind().
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Synopsys HSDK clock controller generates and supplies clocks to various
controllers and peripherals within the SoC.
Each clock has assigned identifier and client device tree nodes can use
this identifier to specify the clock which they consume. All available
clocks are defined as preprocessor macros in the
dt-bindings/clock/snps,hsdk-cgu.h header and can be used in device
tree sources.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Fix a copy-paste typo in the clock table entry, s/7795/7796/.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add rk3128 clock driver and cru structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Differentiate the generic clock source selection value from the parent
clock index to fix the incorrect assignment of the generic clock
source selection.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
To get the same behavior as the Linux driver, instead of selecting
the closest inferior rate, select the closest inferior or superior
rate
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
What the AT91_UTMI depends on SPL_DM isn't right. AT91_UTMI is not
only used in SPL, also in other place, even if SPL_DM isn't enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Like STM32H7, now STM32F4/F7 clock drivers are binded by
MFD stm32_rcc driver.
This also allows to add reset support to STM32F4/F7 SoCs family.
As Reset driver is not part of SPL supported drivers, don't bind it
in case of SPL to avoid that stm32_rcc_bind() returns an error.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Now that clk_stm32f7.c manages clocks for both STM32F4 and F7 SoCs
rename it to a more generic clk_stm32f.c
Fix also some checkpatch errors/warnings.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 and STM32F7 RCC clock IP are very similar.
Same driver can be used to managed RCC clock for
these 2 SoCs.
Differences between STM32F4 and F7 will be managed using
different compatible string :
_ overdrive clock is only supported by STM32F7
_ different sys_pll_psc parameters can be used between STM32F4
and STM32F7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Add a dedicated stm32f7 compatible string to use clk_stm32f7
driver with both STM32F4 and STM32F7 SoCs.
It will be needed to manage differences between these 2 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Add xHCI entry into the clock tables, so that the xHCI USB driver
can enable the clock for the xHCI block via clock framework.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The MSTP registers were poked in boards/renesas/rcar-common/common.c
in arch_preboot_os hook thus far to shut down the clock before Linux
takes over. With DM, this is no longer needed and we can do the same
in the clock driver .remove callback. This patch adds such a .remove
callback for R8A7795 and R8A7796.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The RK3399 clk driver still has a left-over use of extract_bits, which
can be replaced by using bitfield_extract from include/bitfield.h.
This rewrites the invocation to use the shared function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Using priv for new sysreset driver binding.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fix clock division factor initialization for RCC_PLLCFGR
registers.
PLLR bits (bit 31-28) in RCC_PLLCFGR must not be cleared,
it's a forbidden value. So update RCC_PLLCFGR using
clrsetbits_le32() to set only necessary bits fields.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Init the CPU and its buses to speed up the boot time.
Move rkclk_init() to a place after rk3399_configure_cpu has defined
at the same time, or else there will be a warning.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fix bit 2 name of PWR_CR3 register to match with the
last STM32H7 reference manual available here :
http://www.st.com/content/st_com/en/support/resources/
resource-selector.html?querycriteria=productId=SS1951$$
resourceCategory=technical_literature$$resourceType=reference_manual
Update also comment about voltage scaling 1 values
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
CLK() macro is a residue of a previously reworked patch,
remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>