The PMIC is configured such that its GPIOs have the correct configuration
at power-up, so no programming is required.
In fact, the current programming is actively wrong, since:
(a) the AS3722 driver configures the GPIO to be an output before setting
its output value, which causes a 0v glitch on the output.
(b) the AS3722 driver configures the GPIO to drive a high voltage from its
VSUP_GPIO power source rather than its VDD_GPIO_LV power source, so the pin
drives 5V not 1.8V as desired.
Solve these problems by removing the code which configures the PMIC GPIOs.
Note that this patch was tested directly on top of v2016.01; since then,
commit 96350f729c "dm: tegra: net: Convert tegra boards to driver model
for Ethernet" prevents PCIe from being initialized. Alternatively, simply
revert that commit to get PCIe Ethernet working again, then apply this
patch to test.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the U-Boot Driver Model(DM) to use the Freescale QSPI driver.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Set Board Configuration Register to select the lpuart pins of various
muxes.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case of error while executing esbc_validate command, SNVS
transition and issue of reset is required only for secure-boot.
If boot mode is non-secure, this is not required.
Similarly, esbc_halt command which puts the core in Spin Loop
is applicable only for Secure Boot.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Chain of Trust is enabled for ARM platforms (LS1021 and LS1043).
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
bootdelay = 0 (To disable Boot Prompt)
bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
A function is created to detrmine if the boot mode is secure
or non-secure for differnt SoC's.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the xparameters file contains a LL_TEMAC definition compile its
driver and the net commands.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
board_pre_init was not called because CONFIG_BOARD_EARLY_INIT_F was not
set. Remove unused function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
board_pre_init was not called because CONFIG_BOARD_EARLY_INIT_F was not
set. Remove unused function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Now that the specific boards have been removed there is no need to
maintain the weak functions.
Fix also CamelCase to make checkpatch happy
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Now that the specific boards have been removed there is no need to
maintain the weak functions.
Fix also CamelCase to make checkpatch happy
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Use space instead of tab in checkboard print to aligned
it with others boards.
Reported-by: David Glessner <david.glessner@rockwellcollins.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
When only sdhci1 IP is enabled and SD_MODE1 bootmode is selected
U-Boot using sdboot1 variable which refers to mmc dev 1.
But this device doesn't exist because only one controller is available.
This patch fix logic around sdboot mode with using sdbootdev internal
variable.
Reported-by: Chris Kohn <ckohn@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Show also EMMC bootmode if selected. There is difference compare to SD
bootmode. Use the same bootcommand till better boot command is created.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Showing information about bootmode is very useful to make sure
that correct bootmode is selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify the SD bootmode value to 0x3 as per latest
spec. Also add new boot mode QSPI 32 bit boot mode
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove SECURE_IOU option which is not needed. U-Boot itself can detect
which EL level it is on and based on that use do platform setup.
It also simplify usage because one Kconfig entry is gone.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_init() is in final elf file but it is not called at all.
Use board_init_late() instead and call gpio_init() from it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
-Remove UART address (It is now part of the dts).
-Include dummy ns16550 clock
-Fix address to last test
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
As a result of the specific board removal, the Makefiles can be
simplified.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
As a result of the specific board removal, the Makefiles can be
simplified.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
The old mail address will stop working soon.
Update it all the files
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
ml507 is just a specialized version of the xilinx-ppc440-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.
Two defconfigs are added:
theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.
theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously, AXP818 ALDO support was partially added to Kconfig, but
never enabled in the board file, nor properly set or configured in
Kconfig. The boards continue to work because the AXP818 is designed
to pair with the A83T/H8, and the default voltages match the reference
design's requirements.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add dts and defconfig for Banana-pi M3 board.
It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Different A83T boards have different DRAM types. Banapi M3 has LPDDR3,
Allwinner Homlet v1.2 has DDR3.
This adds groundwork to support for new DRAM type for A83T.
Introduce CONFIG_DRAM_TYPE, It'll be 3 for DDR3 and 7 for LPDDR3, must
be set in respective board defconfig.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we support PSCI and various security switches, we can let
U-boot boot Linux into non-secure and HYP mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
IR chip on all the boards are required to be used in Intel mode
to support VID. VDD will not be adjusted if IR chip is used in
other modes.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Users migrating Freescale's PowerPC SoC U-Boot code to their custom
board, often overlook the need to execute set_liodns() and
setup_portals() being called by platform files.
So Move set_liodns() and setup_portals() to common u-boot boot
sequence
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
