This patch adds OMAP3 cpu type auto detection based on OMAP3 register
and removes hardcoded values.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
With BeagleBoard revision C some HW changes are introduced (e.g. PinMUX)
which might need different software handling. For this, GPIO pin 171 (GPIO
module 6, offset 11) can be used to check for board revision. If this pin
is low, we have a rev C board. Else it must be a revision Ax or Bx board.
To handle board differences you can call function beagle_get_revision().
E.g.:
if (beagle_get_revision()) {
/* do special revision C stuff here */
}
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
The current MMC infrastructure relies on the existence of an
arch-specific header file. This isn't necessary, and a couple
drivers were forced to implement dummy files to meet this requirement.
Instead, we move the stuff in those header files into a more appropriate
place, and eliminate the stubs and the #include of asm/arch/mmc.h
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have common defines that we duplicate in various ways. Having an
arch specific config.h gives us a common location for those defines.
Eventually we should be able to replace this when we have proper
Kconfig support.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
virt_to_phys() returns the physical address given a virtual. In most
cases this will be just the input value as the vast majority of
systems run in a 1:1 mode.
However in systems that are not running this way it should report the
physical address or ~0 if no mapping exists for the given virtual
address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
AT91_BASE_EMAC is never used outside the board specific files,
so replace its usage by the board specific AT91xxx_BASE_EMAC.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
atmel_lcdfb doesn't actually need anything from asm/arch/hardware.h. It
includes a file that does, asm/arch/gpio.h, but this file doesn't
include <asm/arch/hardware.h> like it's supposed to.
Add the missing include to asm/arch/gpio.h and remove the workaround
from the atmel_lcdfb driver. This makes the driver compile on avr32.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Added new CONFIG_DISABLE_CONSOLE define and GD_FLG_DISABLE_CONSOLE.
When CONFIG_DISABLE_CONSOLE is defined, setting
GD_FLG_DISABLE_CONSOLE disables all console input and output.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Correct the mx31_gpio_mux() function to allow changing all i.MX31 IOMUX
contacts instead of only the first 256 ones as is the case prior to
this patch.
Add missing MUX_* macros and update board files to use the new macros.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Tried fixing NAND support for the at91rm9200dk board; untested.
Disabled NAND support in the csb637 board config file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for the Lyrtech SFF-SDR board,
based on the TI DaVinci architecture (ARM926EJS).
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Philip Balister <philip@balister.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This moves the MMC and SD Card command definitions from
include/asm/arch/mmc.h into include/mmc.h. These definitions are
given by the MMC and SD Card standards, not by any particular
architecture.
There's a lot more room for consolidation in the MMC drivers which
I'm hoping to get done eventually, but this patch is a start.
Compile-tested for all avr32 boards as well as lpc2292sodimm and
lubbock. This should cover all three mmc drivers in the tree.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Currently, both are defined as an unsigned long, but
should be phys_size_t. This should result in no real change,
since phys_size_t is currently an unsigned long for all the
default configs. Also add print_lnum to cmd_bdinfo to deal
with the potentially wider memsize.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
AVR32 and AT91SAM9 both have their own identical definitions of
container_of() taken from the Linux kernel. Move it to common.h so
that all architectures can use it.
container_of() is already used by some drivers, and will be used
extensively by the new and improved SPI API.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This way we become able to utilize the full post_log_word for POST
activities (overwise, POST ECC, which has 0x8000 ID, could be
erroneously treated as started in post_output_backlog() even if there
was actually no POST ECC run (because of OCM POST failure, for
example).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Don't run futher tests in case of a test fails that is marked as
POST_STOP.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
The AT91CAP9 revC CPU has a few differences over the previous,
revB CPU which was distributed in small quantities only (revA was
an internal Atmel product only).
The revC silicon needs a special initialisation sequence to
switch from the internal (imprecise) RC oscillator to the
external 32k clock.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the ATMEL LCDC driver which is used on some
AT91 and AVR platforms.
Is has been tested with the AT91CAP9ADK, AT91SAM9261EK, AT91SAM9263EK and
AT91SAM9RLEK boards. Adaptation for AVR32 should probably be easy.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9RL chip and the AT91SAM9RLEK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
When doing the AT91CAP9/AT91SAM9 port, a number of header files were
copied from the Linux kernel sources. This patch explicitly specifies
this origin for all the copied headers, and for those missing copyright
information, adds it.
Additionaly, the header file 'at91sam926x_mc.h' has been superceeded
in the latest kernel sources by 'at91sam9_smc.h'.
The copyright information has been confirmed by the AT91 Linux kernel
maintainer, Andrew Victor <avictor.za@gmail.com>.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
When applying the AT91CAP9 patches upstream, something transformed
the '@' character into the ' <at> ' sequence.
The patch below restores the original form in all the places where
it has been modified (the AT91CAP9 files, the AT91SAM9260 files which
were copied from AT91CAP9, and a couple of other files where the
' <at> ' sequence was present).
Signed-off-by: Stelian Pop <stelian@popies.net>
When doing the AT91CAP9/AT91SAM9 port, a number of header files were
copied from the Linux kernel sources. This patch explicitly specifies
this origin for all the copied headers, and for those missing copyright
information, adds it.
Additionaly, the header file 'at91sam926x_mc.h' has been superceeded
in the latest kernel sources by 'at91sam9_smc.h'.
The copyright information has been confirmed by the AT91 Linux kernel
maintainer, Andrew Victor <avictor.za@gmail.com>.
Signed-off-by: Stelian Pop <stelian@popies.net>
According to schematics and to RedBoot sources, the MX31ADS uses a 32768Hz
oscillator as a SKIL source. Fix previously wrongly assumed 32000Hz value.
Also fix a typo when verifying a jumper configuration. While at it, make
two needlessly global functions static.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
When applying the AT91CAP9 patches upstream, something transformed
the '@' character into the ' <at> ' sequence.
The patch below restores the original form in all the places where
it has been modified (the AT91CAP9 files, the AT91SAM9260 files which
were copied from AT91CAP9, and a couple of other files where the
' <at> ' sequence was present).
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by
Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This is an SPI driver for i.MX and MXC based SoCs from Freescale. So far
only implemented and tested on i.MX31, can with a modified register layout
and definitions be used for i.MX27, I think, MXC CPUs have similar SPI
controllers too.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Also add CONFIG_PHYS_64BIT on powerpc to deal with 32-bit ppc's
that have larger physical addresses like 44x, 85xx, and 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
