Tested with MTA72ASS8G72PSZ-2S6G1. This is 3DS RDIMM module with x4
DDR chips. LS2088ARDB needs to be modified to connect all DQS signals.
Some of them are grounded by default for x8 chips. Tested with RDIMM
MTA18ASF2G72PDZ on main memory controllers. DP-DDR doesn't support
RDIMM. Dropped related timing table.
Signed-off-by: York Sun <york.sun@nxp.com>
DDR controllers always use binding register to determine the memory
space to perform data initialization. In case of controller interleaving,
the space is doubled, resulting twice long wait. It wasn't too bad until
the memory capacity increases. To reduce the wait time, reduce the
binding space to half and restore it after data initialization.
Three-way interleaving is no longer used and is removed.
Signed-off-by: York Sun <york.sun@nxp.com>
DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.
Signed-off-by: York Sun <york.sun@nxp.com>
On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.
Signed-off-by: York Sun <york.sun@nxp.com>
For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.
Signed-off-by: York Sun <york.sun@nxp.com>
For for case of lazyapply method, API fdt_fixup_board_enet() gets
invoked before DPL being deployed. This leads to an issue that
fsl-mc fdt fixup status marked as fail and dprc driver didn't get
registered in linux boot.
Fixes this issue by calling fdt_fixup_board_enet() for case when
DPL is deployed successfully in lazyapply method.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
'select n' selects a constant symbol, which is meaningless and has no
effect. Maybe this was meant to be a 'default n', though bool and
tristate symbols already implicitly default to n.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which does more strict checking here:
kconfiglib.KconfigSyntaxError: board/google/Kconfig:34: Couldn't parse ' select n': expected nonconstant symbol
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The variable t_rfc is never used, so drop it. The variables ddr_wctl
and ddr_wcmd are only used in certain manual instances, so guard their
declaration by the same check as their use.
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
For debugging U-Boot in qemu-x86 the relocation address is needed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot on QEMU does not build ACPI table by ourself, instead it uses
the prebuilt ACPI table via the qfw interface. This implements the
qfw version of acpi_get_rsdp_addr() for setup_zimage().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At present the acpi_rsdp_addr variable is directly referenced in
setup_zimage(). This changes to use an API for better encapsulation
and extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no JTAG symbol in the "Boot mode" choice. JTAG_MODE was
probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection JTAG (undefined) of <choice> (defined at arch/arm/cpu/armv8/zynqmp/Kconfig:107) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of ZynqMP boards
to respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of Microblaze board to
respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of Zynq boards
to respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove SPL_BUILD dependency from zynqmp.c and move it to header file.
Use only one symbol for including psu_init.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Arasan NFC driver requires the self-init mode,
so it should select it.
Instead of having the config header define the macro,
it's cleaner to select the option at the Kconfig level.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrects the ecc address calculation before updating
to ecc register. The ecc address has to be calculated based on
page, oob and ecc sizes of the device.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for ondie ecc. As of now
this adds support for micron parts which supports
ondie ecc.
Didn't found any better way to detect ondie ecc
support by a device except sorting out with
manufacture and device id's.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move common part of ecc structure initialization to
arasan_nand_init() routine.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only emmc functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
emmc support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only nand functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
nand support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DDR less systems are possible for configuration like mini qspi
and making DDR region as normal memory may cause speculative
access which results u-boot hang if DDR is absent. So, this
patch fixes the issue by not making DDR memory region
entry into MMU table.
Future solution is to prepare MMU table per memory node in dts instead
of hard code DDR addresses.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Drop the space before/after '<' and '>'; and
separate the entries to be a bit more readable.
Reported-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
BOOTCOMMAND is composed with distro_bootcmd but this variable is not
present. Enabling distro defaults setting is fixing it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are two reasons for doing this change.
There is still !DM driver for xilinx soft gpio IP and especially it is
saving some space for memory constrained boards like cse (almost ~400B).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not enable DM_ETH/MMC if subsystems are not enabled.
This saves memory for memory constrained boards like cse.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to enable BLK by default for all boards which is just
increasing memory footprint for memory contrained boards like cse.
zc770s are also saving some space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet cable is not connected for xm011 that's why disable all
ethernet related configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is good to see this string to make sure that u-boot which runs on the
board is the same which should run there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the 8GB PCIe High area as device memory.
Also extend the DDR High area to cover the full 32GB range.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add check if boot_targets exists in environment and then
generate new_targets env accordingly. Performing strlen on
null address causes it to fail with exception if isolation
is enabled with DDR address zero as secure. It works with out
isolation enabled as zero is valid address but it may lead to
junk values in boot_targets.
This patch fixes the issue by checking return value of env_get
so that it generate boot_targets properly.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These are defined, but not referenced at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch is fixing the following Warning:
arch/arm/mach-zynq/ps7_spl_init.c:133:24: warning: comparison between
signed and unsigned integer expressions [-Wsign-compare]
while (ioread(addr) < delay)
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770-xm011 is x8 width configuration. This FMC card has also x16
variant which requires different ps7_init configuration. This patch adds
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
