U-Boot on this board grew a long time ago past the 384 KiB that
it reserves for the U-Boot image, before the environment. Thus,
saveenv overwrites the U-Boot image and bricks the board.
I tried to find out when U-Boot grew beyond this point, but there is a
long stretch in the history where this board did not build -- and
AFAICT when it did fit in 384 KiB, it was missing vital features such
as fdt support. Turning off CONFIG_VIDEO was not enough to make it
fit. Thus, I don't think we have any choice other than to move the
environment.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_PHY_AQ1202 is no longer needed, use CONFIG_PHY_AQUANTIA.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Support SODIMM D3XP12081XL10AA 1866MT/s on T2080RDB.
Enable CONFIG_CMD_MEMTEST as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Now cortina driver uses macro CONFIG_SYS_CORTINA_FW_IN_NOR
to define that firmware of cortina driver is stored in the
nor flash.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
QEMU 2.3 changes the address layout of the CCSR map in the PV ppce500 machine
to reside in higher address space.
Unfortunately, this exposed a glitch in u-boot for ppce500: While providing
a function to dynamically evaluate the CCSR region's position in physical
address space, we never used it. Plus we forgot to support 64bit physical
addresses.
This patch fixes that mishap, making u-boot work fine with latest QEMU again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Make the sandbox setup more generic/examplary by including
config_distro_defaults.h and config_distro_bootcmd.h.
Among other things this makes it easy to test whether images will boot
though with the standard distro bootcmds by running e.g:
u-boot -c 'host bind 0 myimage.img ; boot'
By default there are 2 target host devices to emulate device with
multiple storage devices (e.g. internal ("host 0") and external
("host 1") and verify that the prioritization and fallbacks do work
correctly.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
More net features enabled and supported on sandbox to allow more testing
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable USB emulation and associated features so that USB can be used in
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Convert this driver over to use driver model. Since all x86 platforms use
it, move x86 to use driver model for SPI and SPI flash. Adjust all dependent
code and remove the old x86 spi_init() function.
Note that this does not make full use of the new PCI uclass as yet. We still
scan the bus looking for the device. It should move to finding its details
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow network devices to be referred to as "eth0" instead of
"eth@12345678" when specified in ethact.
Add tests to verify this behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox driver will now generate response traffic to exercise the
ping command even when no network exists. This allows the basic data
pathways of the DM to be tested.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic network support to sandbox which includes a network driver.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support running U-Boot as a coreboot payload. Tested peripherals include:
- Video (HDMI and DisplayPort)
- SATA disk
- Gigabit Ethernet
- SPI flash
USB3 does not work. This may be a problem with the USB3 PCI driver or
something in the USB3 stack and has not been investigated So far this is
disabled. The SD card slot also does not work.
For video, coreboot will need to run the OPROM to set this up.
With this board, bare support (running without coreboot) is not available
as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since Chromebooks mostly have similar configuration, put it in a common
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms
even have up to 5. This adds support for every controller on each supported
platform, which is especially useful when using expansion ports on single-board-
computers.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI
controller. However, other platforms using MVTWSI may come with more: this is
the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found
on the same chip.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
This consolidates the flash settings for the Integrator
and activates the new ARM flash image support for them
so images can be loaded by name from flash.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This modifies the vexpress64 Juno configuration so that
it will by default load and boot a kernel and a device tree
from the images stored in the NOR flash. When we are
at it, also define the proper command line for the Juno and
indicate that the USB stick (/dev/sda1) is the default
root file system.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Work_92105 from Work Microwave is an LPC3250-
based board with the following features:
- 64MB or 128MB SDR DRAM
- 1 GB SLC NAND, managed through MLC controller.
- Ethernet
- Ethernet + PHY SMSC8710
- I2C:
- EEPROM (24M01-compatible)
- RTC (DS1374-compatible)
- Temperature sensor (DS620)
- DACs (2 x MAX518)
- SPI (through SSP interface)
- Port expander MAX6957
- LCD display (HD44780-compatible), controlled
through the port expander and DACs
This board has SPL support, and uses the LPC32XX boot
image format.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
There're 2 versions of motherboards that could be used in ARC SDP.
The only important difference for U-Boot is different NAND IC in use:
[1] v2 board (we used to support up until now) sports MT29F4G08ABADAWP
while
[2] v3 board sports MT29F4G16ABADAWP
They are almost the same except data bus width 8-bit in [1] and 16-bit
in [2]. And for proper support of 16-bit data bus we have to pass
NAND_BUSWIDTH_16 option to NAND driver core - which we do now knowing
board type we're running on.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
