c2dd0d4554 added dcache_enable()
to board_init_r(). This enables d-cache for all ARM boards.
As a result some of the arm boards that are not cache-ready
are broken. Revert this change and allow platform code to
take the decision on d-cache enabling.
Also add some documentation for cache usage in ARM.
Signed-off-by: Aneesh V <aneesh@ti.com>
This patch adds support for software I2C for GONI and Universal C210 reference targets.
It adds support for access to GPIOs by number, not as it is present,
by bank and offset.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
These functions provide access to the high resolution microsecond timer
and tidy up a global variable in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
There was already a command to show the processor clocks
for PowerPC (clocks). For i.MX, the "clockinfo" command
was introduce. The patch sets the same command name used on
PowerPC.
A nasty and not needed newline is also dropped in the help for
the command.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This is a port of the official PLL errata workaround from Freescale to
mainline u-boot.
The PLL's in the i.MX51 processor can go out of lock due to a metastable
condition in an analog flip-flop when used at high frequencies.
This workaround implements an undocumented feature in the PLL (dither
mode), which causes the effect of this failure to be much lower (in terms
of frequency deviation), avoiding system failure, or at least decreasing
the likelihood of system failure.
Signed-off-by: David Jander <david@protonic.nl>
This change is driven by need of general gpio_* functions,
which as their parameter are accepting the GPIO pin number, NOT
block and pin.
This makes the code alike to omap, and allows for using more
generic frameworks (e.g. software I2C).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
gd->bd pointer has been used prior been initialized.
Move the relevant code after the initialization.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This deletes the integrator split_by_variant.sh script and
defines a number of unique board types for the core modules
that are meaningful to support for the Integrator AP/CP, i.e.
the ones that did not just say "unsupported core module" in
split_by_variant.sh. If more core modules need to be supported
they are easy to add.
We delete all the old cruft in Makefile and MAKEALL that was
working around the old way of building boards. We create a
unique config file per board to satisfy the build system, but
they are just oneliners that include the existing
integratorap.h and integratorcp.h configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some cases (e.g. bootm with a elf payload which is already at the right
position) there is a in place copy of data to the same address. Catching this
saves some ms while booting.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This driver can be used for kirkwood SoCs by enabling CONFIG_RTC_MV. Tested on
Global Scale Technologies Dreamplug.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Rework for AT91SAM9263 SoC, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
Rework for AT91SAM9RL SoC, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: US->USART, cosmetics
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Bits 0..3 in cs_mask = CS0..CS3 in SPI mode require it to be peripheral
Bits 4..7 in cs_mask = CS0..CS3 in GPIO mode require it to be output
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
The CONFIG_AT91RM9200_USART is an remnant of
18ed5e9550 which deleted the
at91rm9200_usart driver.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The CONFIG_AT91_LEGACY warning became obsolete due to complete removal of
at91rm9200 arch code in arm920t.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The big "ARM: remove broken boards" series deletes all boards using
obsolete arm920t/at91rm9200 arch code. Therefore we can safely remove
this code now.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
TPS62361 is the new power supply used in OMAP4460 that
supplies vdd_mpu.
VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies
vdd_iva. VCORE3 is not used in OMAP4460.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Add mkimage support for OMAP boot image
- Add support for OMAP boot image(MLO) generation in the new
SPL framework
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Add MMC raw and FAT mode boot support for OMAP
- Provide a means by which parameters passed by ROM-code
can be saved in u-boot.
- Save boot mode related information passed by OMAP4 ROM-code
and use it to determine where to load the u-boot from
- Assumes that the image has a mkimage header. Gets the
payload size and load address from this header. If the
header is not detected assume u-boot.bin as payload
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Provide alternate implementations of board_init_f()
board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
it to board config header from config.mk
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Allow SPL to have .bss disjoint from rest of the image
- Allow for .bss setup in CONFIG_SPL_BUILD case too.
- Take care of the special case where relocation offset = 0.
- Compile out exception handling code and install a simpler
vector
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Identify SDRAM devices connected to EMIF automatically:
LPDDR2 devices have some Mode Registers that provide details
about the device such as the type, density, bus width
etc. EMIF has the capability to read these registers. If there
are no devices connected to a given chip-select reading mode
registers will return junk values. After reading as many such
registers as possible and matching with expected ranges of
values the driver can identify if there is a device connected
to the respective CS. If we identify that a device is connected
the values read give us complete details about the device.
This along with the base AC timings specified by JESD209-2
allows us to do a complete automatic initialization of
SDRAM that works on all boards.
Please note that the default AC timings specified by JESD209-2
will be safe for all devices but not necessarily optimal. However,
for the Elpida devices used on Panda and SDP the default timings
are both safe and optimal.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Calculate EMIF register values based on AC timing parameters
from the SDRAM datasheet and the DDR frequency rather than
using the hard-coded values.
For a new board the user doen't have to go through the tedious
process of calculating the register values. Instead, just
provide the AC timings from the device data sheet as input
and the driver will automatically calculate the register values.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add support for:
1. DPLL locking
2. Initialization of clock domains and clock modules
3. Setting up the right voltage on voltage rails
This work draws upon previous work done for x-loader by:
Santosh Shilimkar <santosh.shilimkar@ti.com>
Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
to SoC directory). Will help in having single SPL for all
boards.
- Non-essential part(the pins not essential for u-boot to function)
need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>