Give the CF/IDE code its own file to keep things cleanly separated. While
we're here, clean up the code to use common functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
While the initdram() function makes sense on some arches, it doesn't for
Blackfin systems as it's always implemented the same way.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
USB0_DRVVBUS pinmux configuration is required for USB functinality
in uboot.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Remove PCI reset, if there is a monarch PMC module.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
convert clrbits_be32 + setbits_be32 to clrsetbits_be32, use out_be32 to set gcr.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The caddy2 is a variant of the already supported vme8349. So we just
add the differences to this board port. To better support those two
boards we switched from fixed SDRAM configuration to usage of
spd_sdram(). This is done by providing a board specific SPD EEPROM
routine with different values for both boards.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
changed to use mkconfig -t option instead, plus misc codingstyle fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The core support for NAND booting is there already, so this patch
is pretty straightforward.
There is one trick though: top level Makefile expects nand_spl to
be in nand_spl/board/$(BOARDDIR), but we can fully reuse the code
from mpc8313erdb boards, and so to not duplicate the code we just
symlink nand_spl/board/freescale/mpc8315erdb to mpc8313erdb.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
o silence make during ln echo
o update documentation
o and avoid:
$ ./MAKEALL MPC8315ERDB_NAND
Configuring for MPC8315ERDB board...
sdram.o: In function `fixed_sdram':
/home/r1aaha/git/u-boot/nand_spl/board/freescale/mpc8313erdb/sdram.c:72: undefined reference to `udelay'
by renaming udelay -> __udelay in the spirit of commit
3eb90bad65 "Generic udelay() with watchdog
support".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Thanks to "Errata to MPC8569E PowerQUICC III Integrated Host Processor
Family Reference Manual, Rev. 0" document, which describes all eSDHC
pins, we can add 4-bits eSDHC support for MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We already map the page cache-inhibited. There is no reason we
shouldn't also be marking it guarded to prevent speculative accesses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than hard coding which TLB entry the FLASH is mapped with we can
use find_tlb_idx to determine the entry.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Davinci: Table driven pinmux configuration
Add code to allow pinmux_config tables to be grouped and configured
as a single resource. This removes multiple calls to the pinmux
configuration code from board_init and allows pinmuxes to be
individually configured and added by data manipulation only.
All related #ifdefs can the be removed from board_init code and
since the compiler optimises away statics, #ifdefs can be reduced in
the data definitions as well.
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
These regulators are not needed to start the kernel and only
cause "incomplete constraints" warnings from kernel, so don't
turn them on to save power.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().
Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
commit eb5eb2b0f7
ppc4xx: Cleanup PPC4xx I2C infrastructure
This patch cleans up the PPC4xx I2C intrastructure:
- Use C struct to describe the I2C registers instead of defines
- Coding style cleanup (braces, whitespace, comments, line length)
- Extract common code from i2c_read() and i2c_write()
- Remove unneeded IIC defines from ppc405.h & ppc440.h
breaks comiling for the KAREF and METROBOX boards.
This patch fixes this issue.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Prototype for gunzip/zunzip was only in lib_generic/gunzip.c and thus
repeated in every file using it. This patch moves the prototypes to
common.h and removes all prototypes distributed anywhere else.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
The preferred serial output comes from the debug board.
When the debug board is disconnected, fall back on using
usbtty from the usb connector on the Zoom2 board.
This shows up as /dev/ttyACM0 in a linux host.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
A previous Commit converted the LAN91C96 Ethernet driver to using the
CONFIG_NET_MULTI API, but did not include full board support. This patch
finishes the job.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This modification is NOT tested on any of the
platforms modified as I dont have them. please
help by testing+building+fixing
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Enable the NET MULTI option and remove build warning
Tested: SDP3430
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
u-boot updates, before starting Linux, the memory node in the
DTS. As this is a "standard" feature, move this functionality
to the cpu.c file for mpc5xxx and mpc512x processors.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch introduces a weak default function for post_hotkey_pressed(),
returning 0, for boards without hotkey support. The long-running tests
won't be started on those boards. This default function was implemented
in many board directories. By implementing this weak default we can
remove all those duplicate versions.
Boards with hotkey support, can override this weak default function
by defining one in their board specific code.
Signed-off-by: Stefan Roese <sr@denx.de>
To update the real memory size in the memory node on the
uc101 and mucmc52 boards call fdt_fixup_memory() in
ft_board_setup().
Signed-off-by: Heiko Schocher <hs@denx.de>
According to the PPC reference implementation the udelay() function is
responsible for resetting the watchdog timer as frequently as needed.
Most other architectures do not meet that requirement, so long-running
operations might result in a watchdog reset.
This patch adds a generic udelay() function which takes care of
resetting the watchdog before calling an architecture-specific
__udelay().
Signed-off-by: Ingo van Lil <inguin@gmx.de>
This patch adds support for A320 evaluation board from Faraday. This board
uses FA526 processor by default and has 512kB and 32MB NOR flash, 64M RAM.
FA526 is an ARMv4 processor and uses the ARM920T source in this patch.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Add new directory for da830evm board
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum
Digital EVM board. See http://www.spectrumdigital.com/
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
Creates a method allowing pin settings to be logically grouped into data
structure arrays and provides an API to configure the pinmux settings to
enable the relevant pin functions.
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
When the board is booted without serial cable attached (which
is how most of them will be used) UART RX is left floating and
sometimes picks noise, which interrupts countdown and enters
U-Boot prompt instead of booting the kernel.
Fix this by setting up internal pullup on UART RX pin. This
does not prevent serial from working as the internal pullup
is weak.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cleans up the s3c24x0 header files:
s4c24x0.h: removes the use of 'volatile' from the S3C24X0_REG8,
S3C24X0_REG16 and S3C24X0_REG32 register typedef's. Registers are always
accessed using the IO accessor functions which cast the register address
as 'volatile' anyway so it isn't required here.
s3c2400.h and s3c2410.h: insert a blank line between the static inline
functions
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
This patch moves the s3c24x0 header files from include/ to
include/asm-arm/arch-s3c24x0/.
checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due
to a non-UTF8 character in David M?ller's name:
ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8
#489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3:
+ * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch
As David's name correctly contains a non-UTF8 character I haven't fixed
these errors.
The 3 warnings were all because of the use of 'volatile' in s3c24x0.h:
WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
#673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35:
+typedef volatile u8 S3C24X0_REG8;
+typedef volatile u16 S3C24X0_REG16;
+typedef volatile u32 S3C24X0_REG32;
I'll fix these errors in another patch.
Tested by running MAKEALL for ARM8 targets and ensuring there were no new
errors or warnings.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
value
The SheevaPlug DevKit is shipped with 4x8 by 1Gb DDR devices in
two banks for a total of 512MB of RAM. Based on this configuration
the existing values for SDRAM address control register are incorrect
and result in random kernel oops as memory is incorrectly accessed
(while for example extracting a large tarball such as a rootfs).
Based on the hardware configuration along with the supporting
documentation from Marvell these are the correct values, as
well this change mimics values previously used in Marvell's own
u-boot git tree for the SheevaPlug.
Other variants of the hardware such as the PogoPlug and TonidoPlug
may have different memory configurations but to properly support
those additional board directories should be maintained or a better
system to support other kwb*.cfg is needed.
Tested on SheevaPlug DevKit.
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
The autoupdate feature is not used on PLU405 boards.
So remove it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
When the board is booted without serial cable attached (which
is how most of them will be used) UART RX is left floating and
sometimes picks noise, which interrupts countdown and enters
U-Boot prompt instead of booting the kernel.
Fix this by setting up internal pullup on UART RX pin. This
does not prevent serial from working as the internal pullup
is weak.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
This patch removes the duplicted implementations of the pci_master_init()
function by introducing a weak default function for it. It can be
overridden by a board specific version.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the duplicted implementations of the pci_pre_init()
function by introducing a weak default function for it. This weak default
has a different implementation for some PPC variants. It can be
overridden by a board specific version.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the duplicted implementations of the pci_target_init()
function by introducing a weak default function for it. This weak default
has a different implementation for 440EP(x)/GR(x) PPC's. It can be
overridden by a board specific version (e.g. PMC440, korat).
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
This patch fixes an ugly behavior of the IL712 magnetic coupler
as used on VOM405. These parts will remember their last state
over a power cycle which might cause unwanted behavior.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes an ugly behavior of the IL712 magnetic couplers
as used on PLU405. These parts will remember their last state
over a power cycle which might cause unwanted behavior.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Somehow I missed the NAND booting targets in the 4xx linker script
consolidation patchset. This patch fixes this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch introduces a weak default function for is_pci_host(),
returning 1. This is the default behaviour, since most boards only
implement PCI host functionality. This weak default can be overridden
by a board specific version if needed.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch consolidates the PPC4xx board specific PCIe configuration
code. This way the duplicated code is removed. Boards can implement a
special, non standard behaviour (e.g. number of PCIe slots, etc) by
overriding the weak default functions.
Signed-off-by: Stefan Roese <sr@denx.de>
The same code exists both inside an #ifdef and outside of it.
Remove the extra code for all the 86xx boards.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 70ed869ea5.
There isn't any need to modify the API for fsl_pci_init_port to pass the
status of host/agent(end-point) status. We can determine that
internally to fsl_pci_init_port. Revert the patch that makes the API
change.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
All these linker scripts can be removed since the new common ppc4xx
linker script should be able to handle all of those boards.
Please test and report problems. Thanks.
Signed-off-by: Stefan Roese <sr@denx.de>
These boards have special linker scripts right now. We can't use the
common 4xx linker script here. So overrride the linker script (LDSCRIPT)
in board/*/config.mk and choose the board specific version.
Signed-off-by: Stefan Roese <sr@denx.de>
Some 4xx Makefiles didn't add $(SOBJ) to their board library. This was
no till now problem, since those boards included this object (init.o
most of the time) directly from their linker scripts. This patch clean
this up, so that all objects are now collected in the board library. This
is in preparation for the upcoming PPC4xx linker script consolidation.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the board IPEK01 based on the MPC5200.
The Futjitsu Lime graphics controller is configured in 16 bpp mode.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
To avoid board-specific code accessing the mb862xx registers directly,
the public function mb862xx_probe() has been introduced. Furthermore,
the "Change of Clock Frequency" and "Set Memory I/F Mode" registers
are now defined by CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx__MMR,
respectively. The BSPs for the socrates and lwmon5 boards have been
adapted accordingly.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Setup QE pin multiplexing for USB function, configure needed BCSRs
and add some fdt fixups.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To make QE UART usable by Linux we should setup pin multiplexing
and turn UCC2 Ethernet node into UCC2 QE UART node.
Also, QE UART is mutually exclusive with UART0, so we can't enable
it if eSDHC is in 4-bits mode on pilot boards, or if it's a prototype
board with eSDHC in 1- or 4-bits mode.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SPI Flash (M25P40) is connected to the SPI1 bus, we need a few
qe_iop entries to actually enable SPI1 on these boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch sets memory window for Serial RapidIO on MPC8569E-MDS
boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add some defines, and adjust TLBe setup to include some
space for eLBC NAND.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
eSDHC is mutually exlusive with UART0 (in 4-bits mode) and I2C2
(in 1-bit mode). When eSDHC is used, we should switch u-boot console to
UART1, and make the proper device-tree fixups.
Because of an erratum in prototype boards it is impossible to use eSDHC
without disabling UART0 (which makes it quite easy to 'brick' the board
by simply issung 'setenv hwconfig esdhc', and not able to interact with
U-Boot anylonger).
So, but default we assume that the board is a prototype, which is a most
safe assumption. There is no way to determine board revision from a
register, so we use hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Originally written by Jason Jin and Mingkai Hu for mpc8536.
When QorIQ based board is configured as a PCIe agent, then unlock/enable
inbound PCI configuration cycles and init a 4K inbound memory window;
so that a PCIe host can access the PCIe agents SDRAM at address 0x0
* Supported in fsl_pci_init_port() after adding pcie_ep as a param
* Revamped copyright in drivers/pci/fsl_pci_init.c
* Mods in 85xx based board specific pci init after this change
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The data being modified was in NOR flash which caused the crash.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These files were autogenerated by EPSON configuration tools.
This patch replaces the autogenerated file headers by the GPL
license notice.
This change is done with the explicit permission
of Epson Research & Development / IC Software Development.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Start of support of
Texas Instruments Software Development Platform(SDP)
for OMAP3430 - SDP3430
Highlights of this platform are:
Flash Memory devices:
Sibley NOR, Micron 8bit NAND and OneNAND
Connectivity:
3 UARTs and expanded 4 UART ports + IrDA
Ethernet, USB
Other peripherals:
TWL5030 PMIC+Audio+Keypad
VGA display
Expansion ports:
Memory devices plugin boards (PISMO)
Connectivity board for GPS,WLAN etc.
Completely configurable boot sequence and device mapping
etc.
Support default jumpering and:
- UART1/ttyS0 console(legacy sdp3430 u-boot)
- UART3/ttyS2 console (matching other boards,
and SDP HW docs)
- Ethernet
- mmc0
- NOR boot
Currently the UART1 is enabled by default. for
compatibility with other OMAP3 u-boot platforms,
enable the #define of CONSOLE_J9.
Conflicts:
Makefile
Fixed the conflict with smdkc100_config by moving omap_sdp3430_config
to it is alphabetically sorted location above zoom1.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
We get a compliation warning when we enable the NAND driver
for DM355 leopard. The waring we get is that we have
an implicit declaration of davinci_nand_init.
It is fixed by including the asm/arch/nand_defs.h header file
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
gpmc_config should not be a variant as it is board specific
hence make it a const parameter
Fixes issues identified by Dirk:
- build issue for zoom2
- warnings for all other OMAP3 platforms using nand/onenand etc
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch removes the Sequoia "bootstrap" command and replaces it
with the now common command "chip_config".
Please note that the patches with the dynamic PCI sync clock
configuration have to be applied, before this one should go in.
This is because Sequoia has 2 different bootstrap EEPROMs, and
the old bootstrap command configured different values depending
on the detected PCI async clock (33 vs. 66MHz). With the PCI sync
clock patches, this is not necessary anymore. The PCI sync clock
will be configured correctly on-the-fly now.
Signed-off-by: Stefan Roese <sr@denx.de>
The offset to the chip select is incorrect.
The change 187af954cf,
omap3: embedd gpmc_cs into gpmc config struct
introduced a problem with the serial gpmc setup.
This patch reverts the chip select to its previous value.
The symptoms of this problem are that the Zoom2
currently hangs.
This was run tested on Zoom2.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch adds the initial support for DM6467 EVM.
Other features like NET and NAND support will be added as follow up patches.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
On Chip BootROM support for P1 and P2 series RDB platforms.
This patch is derived from latest On Chip BootROM support on MPC8536DS
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
NAND Boot support for P1 and P2 series RDB platforms.
This patch is derived from NAND Boot support on MPC8536DS.
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
All versions between now and since this commit:
commit bd76729bcb
MPC86xx: set CONFIG_MAX_MEM_MAPPED to 2G by default
will fail to allow the SBC8641D to get past DDR init, because the
LAW config was overlapping. Eventually this board will do SPD
EEPROM config, but for now this gets the board working again.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch re-formats the arm920t s3c24x0 driver files, excluding the nand
driver, in preparation for changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4 and 2/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds new board SMDKC100 that uses s5pc100 SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This patch implements several updates:
-disable CONFIG_ENV_OVERWRITE
-add new hardware style variants and set the arch numbers appropriate
-pass the serial# and hardware revision to the kernel
-removed unused macros from include/configs/meesc.h
-fixed multiline comment style
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.
This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Switch from space-based indentation to tab-based in mux configs, as pointed
out by WD at:
http://lists.denx.de/pipermail/u-boot/2009-September/061241.html
Nothing but whitespace changes in this patch (diff -w gives no output).
Signed-off-by: Olof Johansson <olof@lixom.net>
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
This patch adds kwbimage configuration file
(used by mkimage utility)
to support u-boot.kwb target on mv88f6281gtw_ge board.
To create Kirkwood boot image to be flashed on SPI Flash,
additional parameter u-boot.kwb need to be passed during make.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch adds kwbimage configuration file
(used by mkimage utility)
to support u-boot.kwb target on rd6281a platform.
To create Kirkwood boot image to be flashed on NAND,
additional parameter u-boot.kwb need to be passed during make.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR
flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII
mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The DaVinci DM365 EVM board specific code was including a header file
which does not exist. So removing this header file.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This fixes the code and the comment according to the original intent of
doing an intensive memory test when PSC6_3 is pulled low on the STK52xx.
Notably PORT_CONFIG will be overridden with this correct code now,
so beware.
The original code only worked by coincidence depending on the PORT_CONFIG
setting from the header file. The new code was tested to ensure that the
(undocumented) memory test still works on the STK52x.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Martin Krause <Martin.Krause@tqs.de>
Minor white-space cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 054197ba and later fixes used an array to initialize some of
the MDDRC parameters; however, the use of an array turned out to be a
bad idea as it was not possible to correlate structure entries to
array indices in readable and reliable way. Now we use a struct
instead, which makes this self-explanatory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This message is printed upon PCIe bus scan, not only upon error, but also
if no PCIe device is detected at all. Since this is not an error, let's
remove this message in this case. We already have the message
"link is not up." if there is no PCIe device present.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI
added
Also:
- changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111
- cleaned up line lengths
- modified all boards that override weak function in this driver
- modified all eeprom standalone apps to work with new driver
- updated blackfin standalone EEPROM app after testing
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
PPC boards are the only users of the current FPGA code which is littered
with manual relocation fixups. Now that proper relocation is supported
for PPC boards, remove FPGA manual relocation.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The following changes allow U-Boot to fully relocate from flash to
RAM:
- Remove linker scripts' .fixup sections from the .text section
- Add -mrelocatable to PLATFORM_RELFLAGS for all boards
- Define CONFIG_RELOC_FIXUP_WORKS for all boards
Previously, U-Boot would partially relocate, but statically initialized
pointers needed to be manually relocated.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch adds support to detect the amount of DDR2 SDRAM
on PMC440 modules. Detection is done by probing through
a list of available and supported hardware configurations
from 1GByte down to 256MB.
The static TLB entry is replaced by dynamically created entries.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The MPC8536E is capable of booting from the on-chip ROM - boot from
eSDHC and boot from eSPI. When power on, the porcessor excutes the
ROM code to initialize the eSPI/eSDHC controller, and loads the mian
U-Boot image from the memory device that interfaced to the controller,
such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or
L2SRAM, then boot from it.
The memory device should contain a specific data structure with control
word and config word at the fixed address. The config word direct the
process how to config the memory device, and the control word direct
the processor where to find the image on the memory device, or where
copy the main image to. The user can use any method to store the data
structure to the memory device, only if store it on the assigned address.
The on-chip ROM code will map the whole 4GB address space by setting
entry0 in the TLB1, so the main image need to switch to Address space 1
to disable this mapping and map the address space again.
This patch implements loading the mian U-Boot image into L2SRAM, so
the image can configure the system memory by using SPD EEPROM.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8536E can support booting from NAND flash which uses the
image u-boot-nand.bin. This image contains two parts: a 4K
NAND loader and a main U-Boot image. The former is appended
to the latter to produce u-boot-nand.bin. The 4K NAND loader
includes the corresponding nand_spl directory, along with the
code twisted by CONFIG_NAND_SPL. The main U-Boot image just
like a general U-Boot image except the parts that included by
CONFIG_SYS_RAMBOOT.
When power on, eLBC will automatically load from bank 0 the
4K NAND loader into the FCM buffer RAM where CPU can execute
the boot code directly. In the first stage, the NAND loader
copies itself to RAM or L2SRAM to free up the FCM buffer RAM,
then loads the main image from NAND flash to RAM or L2SRAM
and boot from it.
This patch implements the NAND loader to load the main image
into L2SRAM, so the main image can configure the RAM by using
SPD EEPROM. In the first stage, the NAND loader copies itself
to the second to last 4K address space, and uses the last 4K
address space as the initial RAM for stack.
Obviously, the size of L2SRAM shouldn't be less than the size
of the image used. If so, the workaround is to generate another
image that includes the code to configure the RAM by SPD and
load it to L2SRAM first, then relocate the main image to RAM
to boot up.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By nature of being based off the MPC8548CDS board, this
board inherited an ENV_SIZE setting of 256k. But since
it has a smaller flash device (8MB soldered on), it has
a native sector size of 128k, and hence the ENV_SIZE was
causing 2 sectors to be used for the environment.
By removing the unused sector, we can push TEXT_BASE up
closer to the end of address space and reclaim that
sector for any other application. This also fixes the
mismatch between TEXT_BASE and MONITOR_LEN reported by
Kumar earlier.
Since this board also supports the ability to boot off
the 64MB SODIMM flash, this change is forward looking
with that in mind; i.e. the settings for MONITOR_LEN
and ENV_SIZE will work when the 512k sectors of the
SODIMM flash are used for alternate boot in the future.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The commit ecad289fc6 (OneNAND: Remove
unused read_spareram and add unlock_all as kernel does) forgot to remove
a local reference to read_spareram in board/micronas/vct/ebi_onenand.c,
which causes the following build failure when configured with OneNAND:
ebi_onenand.c: In function 'onenand_board_init':
ebi_onenand.c:196: error: 'struct onenand_chip' has no member named 'read_spareram'
make[1]: *** [ebi_onenand.o] Error 1
make[1]: *** Waiting for unfinished jobs....
make: *** [board/micronas/vct/libvct.a] Error 2
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The latest PPC4xx register cleanup patch missed some SDRAM defines.
This patch now changes lower case UIC defines to upper case. Also
some names are changed to match the naming in the IBM/AMCC users
manuals (e.g. mem_mcopt1 -> SDRAM0_CFG).
Signed-off-by: Stefan Roese <sr@denx.de>
The latest PPC4xx register cleanup patch missed the UIC defines.
This patch now changes lower case UIC defines to upper case.
Signed-off-by: Stefan Roese <sr@denx.de>
With this patch we can change QE USB mode without need to hand-edit
the device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes various ethernet issues with gigabit links handling
in U-Boot. The workarounds originally implemented by Kim Phillips for
Linux kernel.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Since commit 5c2ff323a9 ("mpc8360emds:
rework LBC SDRAM setup"), LBC SDRAM is available for use in Linux.
Though, it appears that QE Ethernet in Gigabit mode can't transmit
large packets when it tries to work with a data in LBC SDRAM (memtest
didn't discover any issues, is LBC SDRAM just too slow?).
With this patch we can still use the board without DDR memory, but
if DDR is available, we don't use LBC SDRAM.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>