Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.
Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000
=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With SPI flash moving to driver model, commit fbb0991 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.
This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a new member 'flags' in struct spi_flash to store the flash flags
during spi_flash_validate_params().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The timeout value is never reset during the transfer. This means that when
transferring more data we eventually trigger the timeout.
This was reported on the mailing list:
"Spansion SPI flash read timeout with AM335x"
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Stefan Roese <sr@denx.de>
CC: Andy Pont <andy.pont@sdcsystems.com>
Tested-by: David Dueck <davidcdueck@googlemail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This reverts commit 562f8df18d.
Note: Even un-reverting this patch couldn't works as expected, based
on the latest testing from Heiko Schocher.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
These methods should be passed a slave device, not a bus. This matches the
old SPI interface. It is important to know which device is claiming the bus
so passing a bus is not that useful.
Reported-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Need to check value of spi_setup_slave and spi_setup_slave_fdt.
If their return value 'bus' is NULL, there is no need to pass it
to following spi_flash_probe_tail.
If 'bus' is null, the original function flow is as following:
spi_flash_probe
|->spi_setup_slave
|->spi_probe_bus_tail
|->spi_flash_probe_slave
|->spi_free_slave
Alougth check the pointer in spi_free_slave is ok, checking the return value
of spi_setup_slave and spi_setup_slave_fdt is better.
Before this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
SF: Failed to set up slave
data abort
pc : [<fff66dcc>] lr : [<fff7628c>]
reloc pc : [<87814dcc>] lr : [<8782428c>]
sp : fdf4fcf0 ip : e630396c fp : fe0d0888
r10: fffa2538 r9 : fdf4feb8 r8 : 02625a00
r7 : 00000002 r6 : fff94ec0 r5 : 00000000 r4 : 9355553c
r3 : 1af0593c r2 : cb3fe030 r1 : fff94eb8 r0 : e59ff018
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
"
After this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
Failed to initialize SPI flash at 0:2
"
No data abort using this patch.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Removed the unnecessary error check from spi_xfer
as the bitlen zero is possible now to deassert the
chip select for which no data is required to be transfered.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Poll both the Read status and Flag status registers
for sucessful erase and program operations for the
Micron devices with E_FSR flag set in params table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
commit aed2fbef5e
"dm: serial: Tidy up the pl01x driver"
caused a regression on (real hardware) PL010 by omitting
to update the line control register when switching baudrate.
Fix this by inlining the missing write to the baud control
register.
Also renaming the set_line_control() function to
pl011_set_line_control() since this function is clearly
PL011-specific, and it won't suffice to call that to
set up line control.
Tested on the Integrator/AP hardware.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name "pch_gbe.%x" exceeds the limit of the name in the
'struct eth_device'. Rename it as just "pch_gbe".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
commit 3c6928fd7b "net: phy: fix warnings with W=1" caused
some PHYs(e.g. CS4315/CS4340) not working. This patch fixes the
warning and make those special PHYs working as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Turn ioaddr into an unsigned long rather than a sized 32-bit variable.
While at it, fix a couple of pointer to integer cast size mismatch
warnings by casting through unsigned long going from pointers to
integers and vice versa.
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some Realtek Ethernet PHYs, like RTL8211D(G/N) and RTL8211E(G), have
interrupts enabled by default. If the interrupt is not treated later by
the OS and the PHY's interrupt line is enabled and shared with other
interrupts, the system will get an interrupt storm. This patch disables
the interrupt for PHY devices that use one of the current Realtek
Ethernet PHY drivers. Some of Realtek Ethernet PHYs, such as RTL8211B(L)
have the interrupt masked. In this case, the functionality of the PHY
should not be afected since this patch brings INER and INSR registers to
their default values.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.
>From section 9.4.1.8 of that manual:
Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.
0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.
In addition, Freescale application note AN2805 is also very clear that
this bit must be set.
This patch reverts a change introduced by commit
457caecdbc.
Testing Done:
Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:
fff9b774: 65 29 80 00 oris r9,r9,32768
Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.
Booted an image on a MPC8541 based board successfully.
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
the ldb clock can be setup in board code (for example set through PLL5).
Update the ldb_clock rate also through board code.
This should be removed, if a clock framework is availiable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
make the ldb_clock configurable through the new define
CONFIG_SYS_LDB_CLOCK. This is needed as the ldb clock is not
always 650000000, for example on the aristainetos2 board,
where the ldb clock derives from PLL5 clock.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
Add driver model support to the designware driver. This reuses most of the
existing code except for some duplication in the probe() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust the error handling to use errno.h instead of returning -1. Change
leaf functions to pass in the arguments they require rather than struct
eth_device. Apart from simplifying the code it makes is easier to reuse
these functions for driver model, since mostly they actually only use
struct dw_eth_priv (which we can keep).
Create a stub for each Ethernet operation function. This will allow use to
share code with the driver model versions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.
Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Finish eliminating CamelCase from net.c and other failures
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within netconsole.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the names of internal packet buffer names that are
used within the network stack and the functions that use them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses use good naming instead of CamelCase. No functional change.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_SPI does not exist in Kconfig in the first place, so the
dependency "depends on DM && SPI" is never met, i.e., DM_SPI_FLASH
can never be enabled (unless you ignore the dependency in an illegal
way. See below.)
Actually, some defconfigs such as socfpga_*_defconfig define
CONFIG_DM_SPI_FLASH=y, but it never appears in the .config file
because of this wrong dependency.
On the other hand, all the Tegra boards enable DM_SPI_FLASH because
config DM_SPI_FLASH
default y
silently ignores the dependency.
Unfortunately, this style of CONFIG definition is abused everywhere
in U-Boot, so we easily miss such a wrong dependency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add driver model support in the XHCI support code so that it can be used by
XHCI USB drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Since driver model will want to use most of the same code for XHCI init
and uninit, put it in a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
