Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
Set the board name appropriately for the board revision that
is detected.
Update the findfdt macro to load the a4 device tree binary.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
[trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and
formatting for that]
Signed-off-by: Tom Rini <trini@ti.com>
Update the EXTRA_ENV_SETTING for the dra7xx.
The console needs to be set to ttyO0 and the
findfdt needs to be updated to load the
dra7xx-evm.dtb file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Correct the console sys prompt to display the correct processor
and the corrent board
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
In the omap4, omap5 and am335x common files add a check to ensure that the fdtfile is
defined after the findfdt macro has run. If the file is not defined then warn the user that the
dtb file is not defined.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file
'exynos5-dt.c' meant for FDT support.
exynos5-dt.c: This file shall contain all code which supports FDT.
Any addition of FDT support for any module needs to be
added in this file.
smdk5250.c: This file shall contain the code which supports non-FDT.
version. Any addition of non-FDT support for any module
needs to be added in this file.
May be, the file smdk5250.c can be removed in near future
when non-FDT is not required.
The Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration.
NOTE:
Please note that all additions corresponding to FDT need to be added into the
file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding
updations into smdk5250.c.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
LP-8x4x is a programmable automation controller by ICP DAS. It is
shipped with outdated U-Boot v1.3.0
This patch adds enough supports to boot the board:
- 128M of 128M SDRAM
- 32M of 48M NOR Flash memory
- 1 of 4 Serial consoles (PXA FFUART)
- 2 of 2 Ethernet controllers (DM9000)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Series-to: u-boot
Series-cc: marex
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
Add MMC support for da830 boards in order to perform
mmc operations(read,write and erase).
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Add some useful functions, and the corresponding definitions.
Add support for powering on the dra7xx_evm SD/MMC LDO
(courtesy Lokesh Vutla <lokeshvutla@ti.com>).
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
The sys_clk on the dra evm board is 20MHZ.
Changing the configuration for the same.
And also moving V_SCLK, V_OSCK defines to
arch/clock.h for OMAP4+ boards.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The registers that are used for device identification
are changed from OMAP5 to DRA7xx.
Using the correct registers for DRA7xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When running the "save" command several times on a mx6qsabresd we see:
U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed
U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed
U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed
This issue is caused by the incorrect usage of CONFIG_SYS_MMC_ENV_PART.
CONFIG_SYS_MMC_ENV_PART should be used to specify the mmc partition that stores
the environment variables.
On some imx boards it is been incorrectly used to pass the partition of kernel
and dtb files for the 'mmcpart' script variable.
Remove the CONFIG_SYS_MMC_ENV_PART usage and configure the 'mmcpart' variable
directly.
Reported-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Prior to Sricharan's cleanup of the boot parameter saving code, we
did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a
problem that the address was pointing to the middle of our running SPL.
Correct to point to the base location of the download image area.
Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being
used. As part of correcting these tests, make use of the fact that
we've always been placing our stack outside of the download image area
(which is fine, once the downloaded image is run, ROM is gone) so
correct the max size test to be the ROM defined top of the download area
to where we link/load at.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Fix typo noted by Peter Korsgaard
Add minimal support (only boot from mmc device) for the Congatec
Conga-QEVAl Evaluation Carrier Board with conga-Qmx6q (i.MX6 Quad
processor) module.
Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
tzpc_init is common for all exynos5 boards, hence move it to
armv7/exynos so that all other boards can use it.
Also update the smdk5250 Makefile and config file.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add i2c2 and 3 to mx6qsabreauto board, i2c3 is multiplexed
use gpio to set steering.
Signed-off-by: Renato Frias <b13784@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
When the mx6slevk board support was added in U-boot there was no device tree
support for mx6sl, so only a FSL 3.0.35 was tested at that time.
Now that mx6slevk support is available we can boot a device tree kernel, by
adjusting CONFIG_LOADADDR into a proper location, so that a non-dt and a dt
kernels can be booted.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
VF610TWR is a board based on Vybrid VF610 SoC.
This patch adds basic support for Vybrid VF610TWR board.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Then we can get rid of the #ifdef CONFIG_TEGRA guard in cpu_init_crit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify
the defines.
- Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere.
- defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G.
Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
The PHY addresses of Teranetics PHY on XAUI riser card are assigned
based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
and slot2
- Configure MDIO for 10Gig Mac
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Provided a default RCW for P5040, then it can use PBL to build
ramboot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 is a subset of T4240. Merge them in config_mpc85xx.h to simplify
the defines. Also move CONFIG_E6500 out of t4qds.h into config_mpc85xx.h.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added a default RCW(1_28_6_12) and PBI configure file for T4240, so it can use
PBL tool to produce the ramboot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add Seagate GoFlex Home support
Start with dockstar configuration
define support for RTC, DATE, SATA and EXT4FS
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
This adds support for the Cortex-A15-TC2 core tile for the Versatile
Express board by ARM. This is mostly a copy of the A5 support file,
but will be extended later with A15 specific options.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
This patch creates a new config for the A5 dual core tile that includes the
generic config for the Versatile Express platform.
The generic config has been modified to provide support for the Extended
Memory Map, as used on the A5 core tile. A5 does not support the legacy
memory map.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
The current ca9x4_ct_vxp platform contains support for a Versatile
Express motherboard with a quad core A9 core tile.
This patch separates the Versatile Express motherboard code and the
A9 specific code, to ease supporting more core tiles in the next
patches.
Andre: merged the first two of Ryan's original patches and did some
checkpatch fixes.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Packed structure cfi_qry contains unaligned 16- and 32-bits members,
accessing which causes problems when cfi_flash driver is compiled with
-munaligned-access option: flash initialization hangs, probably
due to data error.
Since the structure is supposed to replicate the actual data layout
in CFI Flash chips, the alignment issue can't be fixed in the structure.
So, unaligned fields need using of explicit unaligned access macros.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-By: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Add sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch enables gigabyte device for SMDK5250.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
